Re: Annoying whitenoise sound coming from snd_hda enabled chipset

From: Yoshihiro Ota <ota_at_j.email.ne.jp>
Date: Sat, 28 Feb 2009 01:52:07 -0500
On Fri, 27 Feb 2009 13:42:58 +0200
Alexander Motin <mav_at_FreeBSD.org> wrote:

> Yoshihiro Ota wrote:
> > On Thu, 26 Feb 2009 22:05:29 +0200
> > Alexander Motin <mav_at_FreeBSD.org> wrote:
> > 
> >> Yoshihiro Ota wrote:
> >>> On Tue, 24 Feb 2009 21:57:27 +0200
> >>> Alexander Motin <mav_at_FreeBSD.org> wrote:
> >>>> Yoshihiro Ota wrote:
> >>>>> In my case, with hdac or pcm device, 8-CURRENT fails to boot very requentry.
> >>>>> It fails to prove a device and doesn't proceed farthar than that point.
> >>>>> Now it only boots once in 5 or 10 reboots.
> >>>>>
> >>>>> When it boots, it prints lots of following messages.
> >>>>>
> >>>>> hdac0: HDA Codec #0: Conexant CX20549 (Venice)
> >>>>> hdac0: unable to allocate widgets!
> >>>>> hdac0: unable to allocate widgets!
> >>>>> hdac0: unable to allocate widgets!
> >>>>> hdac0: unable to allocate widgets!
> >>>>> hdac0: unable to allocate widgets!
> >>>>> hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> >>>>> hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> >>>>> hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> >>>>> hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> >>>>> hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
> >>>>>
> >>>>> I think this started happening about a week ago or so, sometime between
> >>>>> 13 and 16th.
> >>>> The only significant change last time was enabling MSI by default. But I 
> >>>> don't think it should lead to such errors. I have tried even operation 
> >>>> completely without interrupts working and there is not such errors. Can 
> >>>> you send me complete verbose dmesg with the problem and `pciconf -lvc` 
> >>>> output?
> >>>>
> >>>> Also you may try to disable MSI by setting 'hint.hdac.0.msi=0' hint.
> >>> Once I disabled snd_hda_load="YES" in /boot/loader.conf, it comes up
> >>> all times.  However, when I run "kldload snd_hda", the system stops responding,
> >>> i.e. crashes.
> >>>
> >>> So, now I added 'hint.hdac.0.msi="0"' in the hint; then, system comes up fine.
> >>> I tried "kldload snd_hda" and got the following output.
> >>> System didn't crash after adding the hint so that I added snd_hda_load="YES"
> >>> back to /boot/loader.conf.
> >> I have committed a patch to the CURRENT that should disable MSI for your 
> >> HDA controller by default. Test it please.
> > 
> > That's r189086, isn't it?
> > 
> > So, for testing, I will remove hint.hdac.0.msi and add 'snd_hda_load="YES"' back.
> > Does that sound valid test?
> 
> Yes. 'snd_hda_load="YES"' is on your wish.

System comes up without problems now.

Thanks,
Hiro
Received on Sat Feb 28 2009 - 05:52:14 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:42 UTC