Re: Call for axe(4) testers.

From: Norikatsu Shigemura <nork_at_FreeBSD.org>
Date: Mon, 5 Jan 2009 01:35:01 +0900
Hi hps!

On Sun, 4 Jan 2009 17:15:05 +0100
Hans Petter Selasky <hselasky_at_c2i.net> wrote:
> > 	I tested on r186730 by alfred_at_.
> > 	1. When my all devices are detached, OS is freeze(not panic).
> When are all devices detached? Can you explain your cable setup and where you 
> unplug? Are there any USB HUBs involved?

	Ah, I did following steps:
	foreach (GU-1000T UE-200TX-G LUA-U2-KTX) {
		Plug
		Unplug -> Freeze
		No key accept
		reset
	}

On plug:
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
ugen1.2: <ASIX Electronics> at usbus1
axe0: <ASIX Electronics AX88772, rev 2.00/0.01, addr 2> on usbus1
miibus1: <MII bus> on axe0
ukphy0: <Generic IEEE 802.3u media interface> PHY 16 on miibus1
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
axe0: Ethernet address: 00:90:cc:e7:6b:20
axe0: link state changed to DOWN
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

devinfo -rv
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
        ehci0 pnpinfo vendor=0x8086 device=0x265c subvendor=0x10f7 subdevice=0x8338 class=0x0c0320 at slot=29 function=7 handle=\_SB_.PCI0.EHCI
            I/O memory addresses:
                0xb0040000-0xb00403ff
          usbus1
            ushub1
              axe0 pnpinfo vendor=0x0b95 product=0x7720 devclass=0xff devsubclass=0xff sernum="" intclass=0xff intsubclass=0xff at port=1 interface=0
                miibus1
                  ukphy0 pnpinfo oui=0xec6 model=0x1 rev=0x1 at phyno=16
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

	I have no USB HUBs, so I pluged into NOTE PC's USB port.

usbconfig list   
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
ugen0.1: <UHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen1.2: <AX88772 ASIX Electronics> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -


> > 	2. GU-1000T doesn't work, but UE-200TX-G works well.
> If your kernel is compiled with KDB, then try pressing CTRL+ALT+ESC to enter 
> the debugger after the freeze. Then dump the backtrace of all the threads. 
> Look for function names containing the word "axe".

	Any key(CTRL+ALT+DEL, etc..) didn't accept.  But I didn't hit
	CTRL+ALT+ESC.  So I'll try to hit it.
Received on Sun Jan 04 2009 - 15:35:11 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:40 UTC