Re: RFC: ATA to CAM integration patch

From: Mike Tancsa <mike_at_sentex.net>
Date: Thu, 02 Jul 2009 15:02:10 -0400
At 03:44 AM 6/28/2009, Alexander Motin wrote:

>I see no any relation to the patch here. I would say it is some 
>BIOS/loader problem, as kernel wasn't yet booted. Have you been ever 
>able to boot this system with AHCI enabled before?

I re-installed the OS on a new drive with a 200906 snapshot, and can 
now boot with AHCI enabled in the BIOS.  The original image was a 
RELENG_7 box that I upgraded to HEAD some time ago. Is there 
something that needs to be manually updated that would not have been 
done as part of the normal buildworld/buildkernel ?  Re-install the 
boot blocks perhaps ?


ahci0: <AHCI controller> port 
0xc000-0xc007,0xbc00-0xbc03,0xb880-0xb887,0xb800-0xb803,0xb480-0xb49f 
mem 0xfadd6000-0xfadd67ff irq 19 at device 31.2 on pci0
ahci0: [ITHREAD]
ahci0: AHCI v1.20 controller with 6 3Gbps ports, PM not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich0: [ITHREAD]
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich1: [ITHREAD]
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich2: [ITHREAD]
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich3: [ITHREAD]
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich4: [ITHREAD]
ahcich5: <AHCI channel> at channel 5 on ahci0
ahcich5: [ITHREAD]

On the ich10 board, its trying to boot up now, but I am getting

uhub8: 4 ports with 4 removable, self powered
(probe2:ahcich2:0:0:0): SIGNATURE: eb14
run_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config
ahcich2: Timeout on slot 4
run_interrupt_driven_hooks: still waiting after 120 seconds for xpt_config
ahcich2: Timeout on slot 5
run_interrupt_driven_hooks: still waiting after 180 seconds for xpt_config
ahcich2: Timeout on slot 6
run_interrupt_driven_hooks: still waiting after 240 seconds for xpt_config
ahcich2: Timeout on slot 7
run_interrupt_driven_hooks: still waiting after 300 seconds for xpt_config
ahcich2: Timeout on slot 8
ada0 at ahcich1 bus 0 target 0 lun 0
ada0: <ST3500410AS CC34> ATA/ATAPI-8 SATA 2.x device
ada0: 300.000MB/s transfers
ada0: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
ada0: Native Command Queueing Enabled


mountroot> ufs:/dev/ada0s1
Trying to mount root from ufs:/dev/ada0s1
GEOM: ada0s1: geometry does not match label (255h,63s != 16h,63s).

And then it hangs there.

         ---Mike 
Received on Thu Jul 02 2009 - 17:02:11 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:51 UTC