Re: setting up wlan with vap - wlan0 doesn't appear

From: Gravisman <gravisman_at_gmail.com>
Date: Sun, 12 Jul 2009 19:39:32 -0700 (PDT)
Sam Leffler-2 wrote:
> 
> Gravisman wrote:
>> I just got an iogear usb wireless adapter to add to my machine which
>> previously only ran a wired interface. After poking around I now see that
>> wireless setup works significantly different in CURRENT than it did in
>> previous releases. I haven't found too terribly much on google, but the
>> basic idea seems to be that I have to setup a wlans interface in rc.conf.
>> So, the following is what I added to rc.conf, which is consistent with
>> the
>> examples I've found, including the one in /usr/src/UPDATING.
>>
>> wlans_zyd0="wlan0"
>> ifconfig_wlan0="WPA DHCP"
>>
>> I see zyd0 interface in ifconfig, but even with these lines added to
>> rc.conf, I'm not getting any wlan0 interface, and I can't list scanned
>> networks on zyd0. Any idea what I'm missing?
>>   
> zyd0 is not where you list networks; if you create wlan0 then you want
> 
> ifconfig wlan0 list scan
> 
> to see the set of ap's found during a scan.
> 
> Try showing the output of ifconfig for starters.  Since you've enabled 
> WPA I'd ask if you've created a wpa_supplicant.conf file for it?  w/o 
> that you won't get WPA setup.
> 
> 

My problem is that wlan0 doesn't show up as an interface. Despite having
added wlans_zyd0="wlan0" to my rc.conf file, my interfaces are as shown
below:

nassy# ifconfig
msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=118<VLAN_MTU,VLAN_HWTAGGING,TSO4>
        ether 00:13:d4:07:c7:2e
        inet 10.0.1.199 netmask 0xffffff00 broadcast 10.0.1.255
        media: Ethernet autoselect (1000baseT <full-duplex,flag0,flag1>)
        status: active
fwe0: flags=8902<BROADCAST,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=8<VLAN_MTU>
        ether 02:11:d8:37:35:aa
        ch 1 dma -1
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        lladdr 0.11.d8.0.0.37.35.aa.a.2.ff.fe.0.0.0.0
plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> metric 0 mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
        options=3<RXCSUM,TXCSUM>
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 
        inet6 ::1 prefixlen 128 
        inet 127.0.0.1 netmask 0xff000000 
zyd0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
        ether 00:21:79:c2:44:82
        media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
        status: no carrier

As you can see, there is no wlan0. So, what might I be missing to actually
get wlan0 setup? Everything I've found just mentions the rc.conf stuff,
which I've done.

-- 
View this message in context: http://www.nabble.com/setting-up-wlan-with-vap---wlan0-doesn%27t-appear-tp24453847p24455296.html
Sent from the freebsd-current mailing list archive at Nabble.com.
Received on Mon Jul 13 2009 - 00:39:33 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:51 UTC