Re: problem on usb boot from mini itx

On Monday 02 March 2009, Nenhum_de_Nos wrote:
> On Mon, March 2, 2009 10:53, Hans Petter Selasky wrote:
> > On Monday 02 March 2009, Nenhum_de_Nos wrote:
> >> hail,
> >>
> >> I'm trying to make a router from a mini itx, but can't get it to boot
> >> from
> >> usb disk or stick. I can boot from usb cdrom and install ok, 7.1 and
> >> 7.0.
> >> but when I try to boot, I get to the point:
> >>
> >> F1 FreeBSD
> >>
> >> and press enter.
> >>
> >> then I get:
> >> Can't work out which disk we are booting from.
> >> Guessed BIOS device 0x80 not found by probes, defaulting to disk0:
> >>
> >> can't load 'kernel'
> >>
> >> Type '?' for a list of commands, 'help' for more detailed help.
> >> OK
> >>
> >> lsdev gives me:
> >>
> >> cd devices:
> >> disk devices:
> >> pxe devices:
> >>
> >> so, I got to the point it can't find my usb disk, but I don't know why
> >> as
> >> in boot cd it says the disk0 ok. so I copied all cd boot stuff
> >> (boot/cdboot/etc) to see if I can use that to again see my disk, but I
> >> got
> >> nowhere :(
> >>
> >> I used the usb disk on other pc and all went fine, even compiled current
> >> (my target branch) to see if most recent usb boot things (read some from
> >> two threads here, not got deep though) and also nothing :(
> >>
> >> is there anything I can do ?
> >>
> >> dmesg follows
> >>
> >> thanks,
> >>
> >> matheus
> >>
> >> the dmesg:
> >>
> >> Copyright (c) 1992-2009 The FreeBSD Project.
> >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> >> 	The Regents of the University of California. All rights reserved.
> >> FreeBSD is a registered trademark of The FreeBSD Foundation.
> >> FreeBSD 8.0-CURRENT #0: Sun Mar  1 22:52:45 BRT 2009
> >>     root_at_cygnus.apartnet:/usr/obj/usr/src/sys/Cygnus8
> >> Timecounter "i8254" frequency 1193182 Hz quality 0
> >> CPU: Transmeta(tm) Crusoe(tm) Processor TM5700 (798.13-MHz 586-class
> >> CPU)
> >>   Origin = "GenuineTMx86"  Id = 0x543  Stepping = 3
> >>   Features=0x84893f<FPU,VME,DE,PSE,TSC,MSR,CX8,SEP,CMOV,PN,MMX>
> >> real memory  = 117374976 (111 MB)
> >> avail memory = 100130816 (95 MB)
> >> kbd1 at kbdmux0
> >> pcib0: <Host to PCI bridge> pcibus 0 on motherboard
> >> pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
> >> pci0: <PCI bus> on pcib0
> >> pci0: <memory, RAM> at device 0.1 (no driver attached)
> >> pci0: <memory, RAM> at device 0.2 (no driver attached)
> >> pci0: <memory, RAM> at device 0.3 (no driver attached)
> >> uhci0: <VIA 83C572 USB controller> port 0xe000-0xe01f irq 15 at device
> >> 9.0
> >> on pci0
> >> uhci0: [ITHREAD]
> >> uhci0: LegSup = 0x201a
> >> usbus0: <VIA 83C572 USB controller> on uhci0
> >> uhci1: <VIA 83C572 USB controller> port 0xe100-0xe11f irq 5 at device
> >> 9.1
> >> on pci0
> >> uhci1: [ITHREAD]
> >> uhci1: LegSup = 0x2010
> >> usbus1: <VIA 83C572 USB controller> on uhci1
> >> ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe8131000-0xe81310ff irq 10
> >> at
> >> device 9.2 on pci0
> >> ehci0: [ITHREAD]
> >> usbus2: EHCI version 1.0
> >> usbus2: <VIA VT6202 USB 2.0 controller> on ehci0
> >> vgapci0: <VGA-compatible display> port 0xe200-0xe2ff mem
> >> 0xe0000000-0xe7ffffff,0xe8120000-0xe812ffff irq 11 at device 13.0 on
> >> pci0
> >> isab0: <PCI-ISA bridge> at device 17.0 on pci0
> >> isa0: <ISA bus> on isab0
> >> atapci0: <VIA 8231 UDMA100 controller> port
> >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe300-0xe30f at device 17.1 on pci0
> >> ata0: <ATA channel 0> on atapci0
> >> ata0: [ITHREAD]
> >> ata1: <ATA channel 1> on atapci0
> >> ata1: [ITHREAD]
> >> pci0: <bridge> at device 17.4 (no driver attached)
> >> vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xe600-0xe6ff mem
> >> 0xe8130000-0xe81300ff irq 15 at device 18.0 on pci0
> >> vr0: Quirks: 0x0
> >> vr0: Revision: 0x51
> >> miibus0: <MII bus> on vr0
> >> ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
> >> ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> >> vr0: Ethernet address: 00:13:21:ee:26:00
> >> vr0: [ITHREAD]
> >> cpu0 on motherboard
> >> pmtimer0 on isa0
> >> atrtc0: <AT realtime clock> at port 0x70-0x71 irq 8 pnpid PNP0b00 on
> >> isa0
> >> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 irq 1 pnpid
> >> PNP0303 on isa0
> >> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> >> kbd0 at atkbd0
> >> atkbd0: [GIANT-LOCKED]
> >> atkbd0: [ITHREAD]
> >> unknown: <PNP0c01> can't assign resources (memory)
> >> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xcc000-0xd5fff pnpid
> >> ORM0000 on isa0
> >> sc0: <System console> at flags 0x100 on isa0
> >> sc0: VGA <16 virtual consoles, flags=0x300>
> >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> >> isa0
> >> ppc0: parallel port not found.
> >> unknown: <PNP0c01> can't assign resources (memory)
> >> Timecounter "TSC" frequency 798131036 Hz quality 800
> >> Timecounters tick every 1.000 msec
> >> usbus0: 12Mbps Full Speed USB v1.0
> >> usbus1: 12Mbps Full Speed USB v1.0
> >> usbus2: 480Mbps High Speed USB v2.0
> >> ugen0.1: <VIA> at usbus0
> >> ushub0: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> >> ugen1.1: <VIA> at usbus1
> >> ushub1: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> >> ugen2.1: <VIA> at usbus2
> >> ushub2: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
> >> ad0: 6149MB <SAMSUNG SV0643D KT100> at ata0-master UDMA33
> >> GEOM: ad0s1: geometry does not match label (255h,63s != 15h,63s).
> >> ushub0: 2 ports with 2 removable, self powered
> >> ushub1: 2 ports with 2 removable, self powered
> >> Root mount waiting for: usbus2
> >> Root mount waiting for: usbus2
> >> ushub2: 4 ports with 4 removable, self powered
> >> Trying to mount root from ufs:/dev/ad0s1a
> >> usb2_alloc_device:1463: set address 2 failed (ignored)
> >> usb2_alloc_device:1499: getting device descriptor at addr 2 failed!
> >> usb2_req_re_enumerate:1414: addr=2, set address failed! (ignored)
> >> usb2_req_re_enumerate:1427: getting device descriptor at addr 2 failed!
> >> usb2_req_re_enumerate:1414: addr=2, set address failed! (ignored)
> >> usb2_req_re_enumerate:1427: getting device descriptor at addr 2 failed!
> >> ugen0.2: <> at usbus0 (disconnected)
> >> uhub_reattach_port:414: could not allocate new device!
> >
> > Hi,
> >
> > What happens if you put an external USB HUB in between ?
>
> nops, I'll try :)
>
> > There is also a ehci.no_hs sysctl which you can try setting to one.
>
> it passes info to loader, right ?
>
> > Also try enabling uhub debugging during boot.
> >
> > sysctl hw.usb2.uhub.debug=15
>
> will this take effect even if I can't get to where freebsd kernel takes
> command ?
>

Yes, you can add it to /boot/loader.conf

--HPS