Hello, when upgrading this morning from a March 1 -current, if_bge stopped working (and irq256: bge0 not showing up in vmstat -i ). Setting hw.pci.enable_msi="0" makes it work again. Nothing noticeable in dmesg.boot : [root_at_siamesetwins /usr/temp]# diff dmesg.boot.OK dmesg.boot.KO 5c5 < FreeBSD 8.0-CURRENT #1: Sun Mar 1 23:38:34 CET 2009 --- > FreeBSD 8.0-CURRENT #0: Tue Mar 10 11:52:39 CET 2009 16,17c16,17 < usable memory = 8581632000 (8184 MB) < avail memory = 8280162304 (7896 MB) --- > usable memory = 8581603328 (8184 MB) > avail memory = 8278331392 (7894 MB) 128d127 < SMP: AP CPU #5 Launched! 129a129 > SMP: AP CPU #5 Launched! 205c205 < tap0: Ethernet address: 00:bd:35:04:00:00 --- > tap0: Ethernet address: 00:bd:29:04:00:00 Full dmesg.boot.OK below. Thanx, Arno ####### Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-CURRENT #1: Sun Mar 1 23:38:34 CET 2009 toor_at_siamesetwins:/usr/obj/raid1/bsd/src-current/sys/S3992 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Quad-Core AMD Opteron(tm) Processor 2354 (2194.52-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x100f23 Stepping = 3 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x802009<SSE3,MON,CX16,POPCNT> AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS> TSC: P-state invariant Cores per package: 4 usable memory = 8581632000 (8184 MB) avail memory = 8280162304 (7896 MB) ACPI APIC Table: <103007 APIC2012> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 cpu4 (AP): APIC ID: 4 cpu5 (AP): APIC ID: 5 cpu6 (AP): APIC ID: 6 cpu7 (AP): APIC ID: 7 MADT: Forcing active-low polarity and level trigger for SCI ioapic0 <Version 1.1> irqs 0-15 on motherboard ioapic1 <Version 1.1> irqs 16-31 on motherboard ioapic2 <Version 1.1> irqs 32-47 on motherboard kbd1 at kbdmux0 acpi0: <103007 XSDT2012> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: Sleep Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, bff00000 (3) failed Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 900 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> at device 13.0 on pci1 pci2: <ACPI PCI bus> on pcib2 atapci0: <ServerWorks HT1000 SATA150 controller> port 0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb807,0xb480-0xb483,0xb400-0xb41f mem 0xfeffe000-0xfeffffff irq 11 at device 14.0 on pci1 atapci0: [ITHREAD] ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: [ITHREAD] ata4: <ATA channel 2> on atapci0 ata4: [ITHREAD] ata5: <ATA channel 3> on atapci0 ata5: [ITHREAD] atapci1: <ServerWorks HT1000 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 2.1 on pci0 ata0: <ATA channel 0> on atapci1 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci1 ata1: [ITHREAD] isab0: <PCI-ISA bridge> at device 2.2 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, USB> at device 3.0 (no driver attached) pci0: <serial bus, USB> at device 3.1 (no driver attached) pci0: <serial bus, USB> at device 3.2 (no driver attached) pci0: <network, ethernet> at device 4.0 (no driver attached) pcib3: <ACPI PCI-PCI bridge> at device 6.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 7.0 on pci0 pci4: <ACPI PCI bus> on pcib4 pci4: <network, ethernet> at device 4.0 (no driver attached) pci4: <network, ethernet> at device 4.1 (no driver attached) pcib5: <ACPI PCI-PCI bridge> at device 8.0 on pci0 pci5: <ACPI PCI bus> on pcib5 pcib6: <PCI-PCI bridge> at device 0.0 on pci5 pci7: <PCI bus> on pcib6 aac0: <Adaptec RAID 3405> mem 0xff400000-0xff5fffff irq 28 at device 14.0 on pci7 aac0: Enabling 64-bit address support aac0: Enable Raw I/O aac0: Enable 64-bit array aac0: New comm. interface enabled aac0: [ITHREAD] aac0: Adaptec 3405, aac driver 2.0.0-1 pcib7: <PCI-PCI bridge> at device 0.2 on pci5 pci6: <PCI bus> on pcib7 pcib8: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pci8: <ACPI PCI bus> on pcib8 pcib9: <ACPI PCI-PCI bridge> at device 10.0 on pci0 pci9: <ACPI PCI bus> on pcib9 pcib10: <ACPI PCI-PCI bridge> at device 11.0 on pci0 pci10: <ACPI PCI bus> on pcib10 vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xd8000000-0xdfffffff,0xff6f0000-0xff6fffff irq 17 at device 12.0 on pci0 acpi_button0: <Power Button> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: [FILTER] cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 cpu4: <ACPI CPU> on acpi0 cpu5: <ACPI CPU> on acpi0 cpu6: <ACPI CPU> on acpi0 cpu7: <ACPI CPU> on acpi0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xce7ff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ppc0: cannot reserve I/O port range Timecounters tick every 1.000 msec ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to deny, logging disabled ad0: 194481MB <Maxtor 6Y200P0 YAR41BW0> at ata0-master UDMA100 aacd0: <Volume> on aac0 aacd0: 69890MB (143134720 sectors) SMP: AP CPU #2 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #7 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #5 Launched! Trying to mount root from ufs:/dev/aacd0s1a tap0: Ethernet address: 00:bd:19:04:00:00 bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x8100> mem 0xff0d0000-0xff0dffff,0xff0c0000-0xff0cffff irq 26 at device 4.0 on pci4 miibus0: <MII bus> on bge0 brgphy0: <BCM5780 10/100/1000baseTX PHY> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bge0: Ethernet address: 00:e0:81:4d:5d:b8 bge0: [ITHREAD] bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x8100> mem 0xff0f0000-0xff0fffff,0xff0e0000-0xff0effff irq 27 at device 4.1 on pci4 miibus1: <MII bus> on bge1 brgphy1: <BCM5780 10/100/1000baseTX PHY> PHY 1 on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bge1: Ethernet address: 00:e0:81:4d:5d:b9 bge1: [ITHREAD] fxp0: <Intel 82551 Pro/100 Ethernet> port 0xec00-0xec3f mem 0xff6eb000-0xff6ebfff,0xff6a0000-0xff6bffff irq 16 at device 4.0 on pci0 miibus2: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> PHY 1 on miibus2 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:e0:81:4d:78:a5 fxp0: [ITHREAD]Received on Tue Mar 10 2009 - 14:08:24 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:43 UTC