Hi, I try to use the iwn drivers on my Dell Latitude D630 laptop on a up-to-date current, but I can't. I've an Intel 4965AGN card, and here is the result of pciconf -lv : iwn0_at_pci0:12:0:0: class=0x028000 card=0x11218086 chip=0x42298086 rev=0x61 hdr=0x00 vendor = 'Intel Corporation' device = 'Intel 4965AGN Intel Wireless WiFi Link 4965AGN(supporting 802.11a/b/g/Draft-N)' class = network I've put on /boot/loader.conf the magics lines: legal.intel_iwn.license_ack=1 if_iwn_load="YES" my /etc/rc.conf is configured like that: wlans_iwn0="wlan0" ifconfig_wlan0="country FR WPA DHCP" and the /etc/wpa_supplicant.conf was tested using 2 others differents wirelles card (USB rum and PCMCIA ath) without problem. But I have this error message on dmesg: iwn0: need multicast update callback iwn0: error, INTR=2000000<SW_ERROR> STATUS=0x0 iwn0: error, INTR=2000000<SW_ERROR> STATUS=0x0 iwn0: iwn_config: configure command failed, error 35 iwn0: iwn_init_locked: could not configure device, error 35 iwn0: iwn_config: configure command failed, error 35 iwn0: iwn_init_locked: could not configure device, error 35 iwn0: iwn_transfer_firmware: timeout waiting for first alive notice, error 35 iwn0: iwn_init_locked: could not load firmware, error 35 (The wireless switch is on the ON position, and this wireless works when booting with Linux Ubuntu). And not association possible... Here are some other information: [root_at_d630]~#ifconfig wlan0 wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 00:1d:e0:72:10:01 inet6 fe80::21d:e0ff:fe72:1001%wlan0 prefixlen 64 scopeid 0x7 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier ssid "" channel 13 (2472 Mhz 11g) regdomain ETSI country F2 authmode WPA1+WPA2/802.11i privacy ON deftxkey UNDEF txpower 30 bmiss 10 scanvalid 60 protmode CTS wme roaming MANUAL [root_at_d630]~#ifconfig wlan0 list scan [root_at_d630]~#ifconfig wlan0 list caps drivercaps=581e001<STA,TXPMGT,SHSLOT,SHPREAMBLE,MONITOR,WPA1,WPA2,WME> [root_at_d630]~#uname -a FreeBSD d630.freenas.org 8.0-CURRENT FreeBSD 8.0-CURRENT #14: Thu Mar 12 14:17:22 CET 2009 root_at_d630.freenas.org:/usr/obj/usr/src/sys/DellD630 amd64 [root_at_d630]~#wpa_supplicant -d -i wlan0 -c /etc/wpa_supplicant.conf Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' update_config=1 ctrl_interface='/var/run/wpa_supplicant' ap_scan=1 Priority group 19 id=0 ssid='Gugus' Initializing interface (2) 'wlan0' Own MAC address: 00:1d:e0:72:10:01 wpa_driver_bsd_set_wpa: enabled=1 wpa_driver_bsd_set_wpa_internal: wpa=3 privacy=1 wpa_driver_bsd_del_key: keyidx=0 wpa_driver_bsd_del_key: keyidx=1 wpa_driver_bsd_del_key: keyidx=2 wpa_driver_bsd_del_key: keyidx=3 wpa_driver_bsd_set_countermeasures: enabled=0 wpa_driver_bsd_set_drop_unencrypted: enabled=1 RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED Added interface wlan0 State: DISCONNECTED -> SCANNING Starting AP scan (broadcast SSID) Trying to get current scan results first without requesting a new scan to speed up initial association Received 0 bytes of scan results (0 BSSes) Scan results: 0 Cached scan results are empty - not posting Selecting BSS from priority group 19 Try to find WPA-enabled AP Try to find non-WPA AP No suitable AP found. Setting scan request: 0 sec 0 usec Starting AP scan (broadcast SSID) ioctl[SIOCS80211, op 103, len 128]: Device not configured Failed to initiate AP scan. Does someone know where the problem is ? Thanks for your help, OlivierReceived on Fri Mar 13 2009 - 05:49:50 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:43 UTC