Hi, Today I have svn up my FreeBSD-8.0-CURRENT to r190389 but it is no longer able to boot, it panics at boot. Here is message I'm getting (I had to write it down to paper :( since I don't have serial attached to this machine: Fatal trap 12: page fault while in kernel mode cpuid =0, apic id = 00 fault virtual address = 0x3c Fault code = supervisor write data, page not present Instruction ponter = 0x8: 0xffffffff8056db9f Stack ponter = 0x10: 0xffffffff813bac70 Code segment = 0x10: 0xffffffff813baca0 = base 0x0, limit 0xfffff, type 0x1b DPL 0, pres 1, long 1, def32 0, gran 1 Processor eflags = resume, iopl = 0 Current process = 0 (swapper) [thread pio 0 tid 10000] stopped at devclass_find_interna+0x10f: orl $0x1, 0x3c(%rax) db> where tracing pid 0 tid 10000 td 0xffffffff80bb5ce0 dev_class_find_internal() at devclass_find_internal+0x10f driver_module_handler() at driver_module_handler+0xb9 module_register_init() at module_register_init+0x7d mi_startup() at mi_startup+0x59 btext() at btext+0x2c db> And here is dmesg from last working kernel I have: Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-CURRENT #0 r189900: Mon Mar 16 22:51:40 CET 2009 root_at_magarac:/usr/src/sys/amd64/compile/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Core(TM)2 Quad CPU Q8200 _at_ 2.33GHz (2333.08-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x10677 Stepping = 7 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x8e39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> TSC: P-state invariant Cores per package: 4 usable memory = 1056894976 (1007 MB) avail memory = 1018724352 (971 MB) ACPI APIC Table: <A_M_I_ OEMAPIC > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <A_M_I_ OEMRSDT> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 3ff00000 (3) failed Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 900 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 vgapci0: <VGA-compatible display> port 0xa000-0xa0ff mem 0xd0000000-0xdfffffff,0xfbae0000-0xfbaeffff irq 16 at device 0.0 on pci1 pci1: <multimedia, HDA> at device 0.1 (no driver attached) uhci0: <Intel 82801I (ICH9) USB controller> port 0x9800-0x981f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f30 usbus0: <Intel 82801I (ICH9) USB controller> on uhci0 uhci1: <Intel 82801I (ICH9) USB controller> port 0x9880-0x989f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f30 usbus1: <Intel 82801I (ICH9) USB controller> on uhci1 uhci2: <Intel 82801I (ICH9) USB controller> port 0x9c00-0x9c1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f30 usbus2: <Intel 82801I (ICH9) USB controller> on uhci2 ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfb9ffc00-0xfb9fffff irq 18 at device 26.7 on pci0 ehci0: [ITHREAD] usbus3: EHCI version 1.0 usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0 pci0: <multimedia, HDA> at device 27.0 (no driver attached) pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 pci5: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci5 pci7: <ACPI PCI bus> on pcib3 amr0: <LSILogic MegaRAID 1.53> mem 0xfaff0000-0xfaffffff irq 18 at device 2.0 on pci7 amr0: Using 64-bit DMA amr0: [ITHREAD] amr0: delete logical drives supported by controller amr0: <LSILogic PERC 4/SC> Firmware 352D, BIOS 1.10, 64MB RAM pcib4: <PCI-PCI bridge> mem 0xfbeffc00-0xfbeffc7f irq 16 at device 0.1 on pci5 pci6: <PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 pci4: <ACPI PCI bus> on pcib5 mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfbdfc000-0xfbdfffff irq 18 at device 0.0 on pci4 msk0: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> on mskc0 can't re-use a leaf (jabbers)! msk0: Ethernet address: 00:1d:60:c9:1a:3e miibus0: <MII bus> on msk0 e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0 e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto mskc0: [FILTER] pcib6: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0 pci3: <ACPI PCI bus> on pcib6 mskc1: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xc800-0xc8ff mem 0xfbcfc000-0xfbcfffff irq 19 at device 0.0 on pci3 msk1: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> on mskc1 can't re-use a leaf (jabbers)! msk1: Ethernet address: 00:1d:60:c9:17:a3 miibus1: <MII bus> on msk1 e1000phy1: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus1 e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto mskc1: [FILTER] pcib7: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0 pci2: <ACPI PCI bus> on pcib7 atapci0: <Marvell 88SX6145 UDMA133 controller> port 0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb807,0xb480-0xb483,0xb400-0xb40f mem 0xfbbffc00-0xfbbfffff irq 16 at device 0.0 on pci2 atapci0: [ITHREAD] ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: [ITHREAD] uhci3: <Intel 82801I (ICH9) USB controller> port 0x9080-0x909f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f30 usbus4: <Intel 82801I (ICH9) USB controller> on uhci3 uhci4: <Intel 82801I (ICH9) USB controller> port 0x9400-0x941f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f30 usbus5: <Intel 82801I (ICH9) USB controller> on uhci4 uhci5: <Intel 82801I (ICH9) USB controller> port 0x9480-0x949f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f30 usbus6: <Intel 82801I (ICH9) USB controller> on uhci5 ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfb9ff800-0xfb9ffbff irq 23 at device 29.7 on pci0 ehci1: [ITHREAD] usbus7: EHCI version 1.0 usbus7: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1 pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci8: <ACPI PCI bus> on pcib8 pci8: <multimedia, video> at device 0.0 (no driver attached) pci8: <multimedia> at device 0.2 (no driver attached) fwohci0: <VIA Fire II (VT6306)> port 0xec00-0xec7f mem 0xfebff800-0xfebfffff irq 19 at device 3.0 on pci8 fwohci0: [ITHREAD] fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:11:d8:00:01:8a:3e:e5 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 dcons_crom0: <dcons configuration ROM> on firewire0 dcons_crom0: bus_addr 0x3e210000 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:11:d8:8a:3e:e5 fwe0: Ethernet address: 02:11:d8:8a:3e:e5 fwip0: <IP over FireWire> on firewire0 fwip0: Firewire address: 00:11:d8:00:01:8a:3e:e5 _at_ 0xfffe00000000, S400, maxrec 2048 sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: fwohci_intr_core: BUS reset fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <Intel ICH9 SATA300 controller> port 0x8000-0x8007,0x7c00-0x7c03,0x7880-0x7887,0x7800-0x7803,0x7480-0x748f,0x7400-0x740f irq 22 at device 31.2 on pci0 atapci1: [ITHREAD] ata4: <ATA channel 0> on atapci1 ata4: [ITHREAD] ata5: <ATA channel 1> on atapci1 ata5: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) atapci2: <Intel ICH9 SATA300 controller> port 0x9000-0x9007,0x8c00-0x8c03,0x8880-0x8887,0x8800-0x8803,0x8480-0x848f,0x8400-0x840f irq 22 at device 31.5 on pci0 atapci2: [ITHREAD] ata6: <ATA channel 0> on atapci2 ata6: [ITHREAD] ata7: <ATA channel 1> on atapci2 ata7: [ITHREAD] acpi_button0: <Power Button> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FILTER] uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 on acpi0 uart0: [FILTER] atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] cpu0: <ACPI CPU> on acpi0 ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] - D, should be 4 [20070320] est0: <Enhanced SpeedStep Frequency Control> on cpu0 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 p4tcc1: <CPU Frequency Thermal Control> on cpu1 cpu2: <ACPI CPU> on acpi0 est2: <Enhanced SpeedStep Frequency Control> on cpu2 p4tcc2: <CPU Frequency Thermal Control> on cpu2 cpu3: <ACPI CPU> on acpi0 est3: <Enhanced SpeedStep Frequency Control> on cpu3 p4tcc3: <CPU Frequency Thermal Control> on cpu3 orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata0: [ITHREAD] ata1 at port 0x170-0x177,0x376 irq 15 on isa0 ata1: [ITHREAD] ppc0: cannot reserve I/O port range Timecounters tick every 1.000 msec firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me) firewire0: bus manager 0 usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 acd0: DVDR <NEC DVD RW ND-4550A/1.09> at ata2-master UDMA33 amr0: delete logical drives supported by controller amrd0: <LSILogic MegaRAID logical drive> on amr0 amrd0: 209640MB (429342720 sectors) RAID 0 (optimal) ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 ugen4.1: <Intel> at usbus4 uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <Intel> at usbus5 uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 ugen6.1: <Intel> at usbus6 uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 ugen7.1: <Intel> at usbus7 uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen6.2: <Logitech> at usbus6 ums0: <Logitech USB-PS/2 Optical Mouse, class 0/0, rev 2.00/20.00, addr 2> on usbus6 ums0: 3 buttons and [XYZ] coordinates SMP: AP CPU #1 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #2 Launched! WARNING: WITNESS option enabled, expect reduced performance. Trying to mount root from ufs:/dev/amrd0s2a lock order reversal: 1st 0xfffffffe54a663d8 bufwait (bufwait) _at_ kern/vfs_bio.c:2549 2nd 0xffffff00019d0a00 dirhash (dirhash) _at_ ufs/ufs/ufs_dirhash.c:275 KDB: stack backtrace: db_trace_self_wrapper() at db_trace_self_wrapper+0x2a _witness_debugger() at _witness_debugger+0x2e witness_checkorder() at witness_checkorder+0x81e _sx_xlock() at _sx_xlock+0x55 ufsdirhash_acquire() at ufsdirhash_acquire+0x33 ufsdirhash_add() at ufsdirhash_add+0x19 ufs_direnter() at ufs_direnter+0x88b ufs_mkdir() at ufs_mkdir+0x633 VOP_MKDIR_APV() at VOP_MKDIR_APV+0x93 kern_mkdirat() at kern_mkdirat+0x2b2 syscall() at syscall+0x1bf Xfast_syscall() at Xfast_syscall+0xab --- syscall (136, FreeBSD ELF64, mkdir), rip = 0x80071e85c, rsp = 0x7fffffffed18, rbp = 0x7fffffffef7e --- KLD snd_hda.ko: depends on kernel - not available linker_load_file: Unsupported file type KLD linux.ko: depends on kernel - not available linker_load_file: Unsupported file type msk0: link state changed to UP Regards, gg.Received on Tue Mar 24 2009 - 19:55:15 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:44 UTC