Andriy Gapon wrote: > on 12/11/2009 21:48 Gary Jennejohn said the following: >> On Thu, 12 Nov 2009 20:52:10 +0200 >> Andriy Gapon <avg_at_icyb.net.ua> wrote: >> >>> on 12/11/2009 19:28 Gary Jennejohn said the following: >>>> A safer way to test this is to enter >>>> set hw.mca.enabled="1" >>>> on the loader command line rather than putting it into loader.conf. >>>> >>>> I just did this on my "consumer" AMD64 board without ill effect. >>> What CPU do you have, could you provide its description from dmesg? >>> Did you stress-tested it enough (like parallel buildworld)? >>> >> I did about 1/2 of a parallel build world (-j3) and then stopped it. I >> figured, if it lasts that long, it should make it all the way through. >> >> CPU: AMD Athlon(tm) Dual Core Processor 4850e (2505.35-MHz K8-class CPU) >> Origin = "AuthenticAMD" Id = 0x60fb2 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> >> Features2=0x2001<SSE3,CX16> >> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> >> AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch> >> TSC: P-state invariant > > Hmm, all people, who do have the problem and who provided cpu information, seem > to have family 16 (0x10, 10h) AMD processors. You have a family 15 one. Maybe > it's that, maybe not. > > BTW, here is my info: > CPU: AMD Athlon(tm) II X2 250 Processor (3013.73-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0x100f62 Stepping = 2 > > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x802009<SSE3,MON,CX16,POPCNT> > AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!> > AMD > Features2=0x37ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT> > TSC: P-state invariant > > here's my dmesg output. No problem at all buildworld/installworld. I also didn't play much with any debugging options, this is the generic one... ;-) Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-RC2 #0: Sun Oct 25 07:27:19 UTC 2009 root_at_mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ (2613.41-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x40f32 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x2001<SSE3,CX16> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8> real memory = 536870912 (512 MB) avail memory = 499974144 (476 MB) ACPI APIC Table: <Nvidia ASUSACPI> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 4 ioapic0 <Version 1.1> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <Nvidia ASUSACPI> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 1fde0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_hpet0: <High Precision Event Timer> iomem 0xfefff000-0xfefff3ff on acpi0 Timecounter "HPET" frequency 25000000 Hz quality 900 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <memory> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, SMBus> at device 1.1 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xfe02f000-0xfe02ffff irq 21 at device 2.0 on pci0 ohci0: [ITHREAD] usbus0: <OHCI (generic) USB controller> on ohci0 ehci0: <NVIDIA nForce4 USB 2.0 controller> mem 0xfeb00000-0xfeb000ff irq 22 at device 2.1 on pci0 ehci0: [ITHREAD] usbus1: EHCI version 1.0 usbus1: <NVIDIA nForce4 USB 2.0 controller> on ehci0 atapci0: <nVidia nForce CK804 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe800-0xe80f at device 6.0 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] atapci1: <nVidia nForce CK804 SATA300 controller> port 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xd400-0xd40f mem 0xfe02c000-0xfe02cfff irq 23 at device 7.0 on pci0 atapci1: [ITHREAD] ata2: <ATA channel 0> on atapci1 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci1 ata3: [ITHREAD] atapci2: <nVidia nForce CK804 SATA300 controller> port 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xc000-0xc00f mem 0xfe02b000-0xfe02bfff irq 21 at device 8.0 on pci0 atapci2: [ITHREAD] ata4: <ATA channel 0> on atapci2 ata4: [ITHREAD] ata5: <ATA channel 1> on atapci2 ata5: [ITHREAD] pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pci1: <ACPI PCI bus> on pcib1 fwohci0: <VIA Fire II (VT6306)> port 0xac00-0xac7f mem 0xfdfff000-0xfdfff7ff irq 17 at device 1.0 on pci1 fwohci0: [ITHREAD] fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:1e:8c:00:00:22:dc:f8 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 dcons_crom0: <dcons configuration ROM> on firewire0 dcons_crom0: bus_addr 0x1ef1c000 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:1e:8c:22:dc:f8 fwe0: Ethernet address: 02:1e:8c:22:dc:f8 fwip0: <IP over FireWire> on firewire0 fwip0: Firewire address: 00:1e:8c:00:00:22:dc:f8 _at_ 0xfffe00000000, S400, maxrec 2048 sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: fwohci_intr_core: BUS reset fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode dc0: <ADMtek AN985 10/100BaseTX> port 0xa800-0xa8ff mem 0xfdffe000-0xfdffe3ff irq 16 at device 6.0 on pci1 miibus0: <MII bus> on dc0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto dc0: Ethernet address: 00:12:17:51:31:ac dc0: [ITHREAD] nfe0: <NVIDIA nForce4 CK804 MCP9 Networking Adapter> port 0xbc00-0xbc07 mem 0xfe02a000-0xfe02afff irq 22 at device 10.0 on pci0 miibus1: <MII bus> on nfe0 atphy0: <Atheros F1 10/100/1000 PHY> PHY 0 on miibus1 atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto nfe0: Ethernet address: 00:1f:c6:be:65:76 nfe0: [FILTER] pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> at device 12.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 13.0 on pci0 pci4: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> at device 14.0 on pci0 pci5: <ACPI PCI bus> on pcib5 vgapci0: <VGA-compatible display> port 0x9c00-0x9cff mem 0xd0000000-0xdfffffff,0xfdef0000-0xfdefffff irq 18 at device 0.0 on pci5 vgapci1: <VGA-compatible display> mem 0xfdee0000-0xfdeeffff at device 0.1 on pci5 acpi_tz0: <Thermal Zone> on acpi0 ACPI Warning: \\_TZ_.THRM._PSL: Return Package type mismatch at index 0 - found [NULL Object Descriptor], expected Reference 20090521 nspredef-1058 atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FILTER] uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppc0: [ITHREAD] ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: [ITHREAD] lpt0: <Printer> on ppbus0 lpt0: [ITHREAD] lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] cpu0: <ACPI CPU> on acpi0 powernow0: <PowerNow! K8> on cpu0 cpu1: <ACPI CPU> on acpi0 powernow1: <PowerNow! K8> on cpu1 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 1.000 msec firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me) firewire0: bus manager 0 usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <nVidia> at usbus0 uhub0: <nVidia OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <nVidia> at usbus1 uhub1: <nVidia EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 acd0: DMA limited to UDMA33, device found non-ATA66 cable acd0: DVDR <LITE-ON DVDRW LH-20A1P/KL0N> at ata0-slave UDMA33 ad8: 152627MB <WDC WD1600AAJS-22PSA0 05.06H05> at ata4-master SATA300 uhub0: 9 ports with 9 removable, self powered uhub1: 9 ports with 9 removable, self powered SMP: AP CPU #1 Launched! Trying to mount root from ufs:/dev/ad8s1a WARNING: / was not properly dismounted ugen0.2: <Dell> at usbus0 ums0: <Dell Dell USB Optical Mouse, class 0/0, rev 2.00/43.01, addr 2> on usbus0 ums0: 3 buttons and [XYZ] coordinates ID=0 ugen0.3: <vendor 0x0d8c> at usbus0 ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to deny, logging disabled nfe0: link state changed to UP hope this helps, Etienne -- Etienne Robillard <robillard.etienne_at_gmail.com> Green Tea Hackers Club <http://gthc.org/> Blog: <http://gthc.org/blog/> PGP Fingerprint: 178A BF04 23F0 2BF5 535D 4A57 FD53 FD31 98DC 4E57Received on Thu Nov 12 2009 - 22:10:46 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:57 UTC