Re: bge(4), 5715S, IBM BladeCenter, no carrier

On Wed, Jan 13, 2010 at 10:38 AM, Oliver Fromme <olli_at_lurza.secnetix.de> wrote:
> Hi,
>
> I've got problems with the bge(4) interfaces on certain
> blades installed within an IBM BladeCenter.  AFAIK these
> are fiber PHYs connected to internal fiber-to-copper
> transceivers inside the blade chassis.
>
> Basically, the interfaces are recognized and attached,
> but I don't get a carrier detected.  The hardware is
> ok, and there is indeed a gigabit switch connected to
> the ports (under Linux, the carrier is detected and the
> interfaces work fine).
>
> ifconfig output:
>
> bge0: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> metric 0 mtu 1500
>        options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
>        ether 00:21:5e:4c:07:22
>        inet 10.2.13.42 netmask 0xffffff00 broadcast 10.2.13.255
>        media: Ethernet 1000baseT <full-duplex> (none)
>        status: no carrier
>
> Related pciconf -lv entries:
>
> pcib3_at_pci0:21:0:0:      class=0x060400 card=0x00000000 chip=0x01031166 rev=0xb5 hdr=0x01
>    vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
>    device     = 'Broadcom dual gigabit, pci bridge (BCM5715)'
>    class      = bridge
>    subclass   = PCI-PCI
> bge0_at_pci0:22:4:0:       class=0x020000 card=0x03671014 chip=0x167914e4 rev=0xa3 hdr=0x00
>    vendor     = 'Broadcom Corporation'
>    device     = 'NetXtreme 5715S Gigabit Ethernet'
>    class      = network
>    subclass   = ethernet
>
> (There are more interfaces; I list bge0 only for brevity.)
>
> Excerpt from dmesg -v:
>
> bge0: <Broadcom NetXtreme Gigabit Fiber Controller, ASIC rev. 0x009003> mem 0x97a00000-0x97a0ffff,0x97a10000-0x97a1ffff irq 24 at device 4.0 on pci22
> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0x97a00000
> bge0: attempting to allocate 1 MSI vectors (8 supported)
> msi: routing MSI IRQ 256 to local APIC 0 vector 56
> bge0: using IRQ 256 for MSI
> bge0: CHIP ID 0x00009003; ASIC REV 0x09; CHIP REV 0x90; PCI-X
> bge0: bpf attached
> bge0: Ethernet address: 00:21:5e:4c:07:22
> bge0: [MPSAFE]
> bge0: [ITHREAD]
>
> Actually this is an 8-stable snapshot from December, but
> with if_bge.c and if_bgereg.h from 9-current as of today,
> because I saw a bunch of commits to HEAD last week.
> (That's why I'm posting this to -current.)

Which PHY is attached to it?

e.g. dmesg | grep miibus?


-- 
Xin LI <delphij_at_delphij.net> http://www.delphij.net