Hmmm, ok I'll look into it. Thanks Mike. Jack On Fri, Jan 22, 2010 at 5:40 AM, Mike Tancsa <mike_at_sentex.net> wrote: > Not sure how easy it is to repeat, but running HEAD from yesterday causes > the em0 do post a > em0: Watchdog timeout -- resetting > to the serial console on a new i3 system that we just got to test with. At > that point, the box's network is no longer responding. It netboots off em0 > so not sure if the hang after that is nfs not recovering or not, but it does > not respond to network traffic at all. > > em0_at_pci0:0:25:0: class=0x020000 card=0x00368086 chip=0x10f08086 > rev=0x06 hdr=0x00 > vendor = 'Intel Corporation' > class = network > subclass = ethernet > cap 01[c8] = powerspec 2 supports D0 D3 current D0 > cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message > cap 13[e0] = PCI Advanced Features: FLR TP > ehci0_at_pci0:0:26:0: class=0x0c0320 card=0x00368086 chip=0x3b3c8086 > rev=0x06 hdr=0x00 > > Copyright (c) 1992-2010 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 9.0-CURRENT #0: Thu Jan 21 15:14:14 EST 2010 > mdtancsa_at_ich10.sentex.ca:/usr/HEAD/obj/usr/HEAD/src/sys/alix i386 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Core(TM) i3 CPU 530 _at_ 2.93GHz (2926.02-MHz 686-class > CPU) > Origin = "GenuineIntel" Id = 0x20652 Stepping = 2 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x98e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT> > AMD Features=0x28100000<NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > TSC: P-state invariant > real memory = 1073741824 (1024 MB) > avail memory = 894119936 (852 MB) > ACPI APIC Table: <INTEL DH55TC > > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > FreeBSD/SMP: 1 package(s) x 2 core(s) > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 4 > ACPI Warning: 32/64X FACS address mismatch in FADT - 3762AE40/ > 03762AD40, using 32 (20091214/tbfadt-586) > ioapic0 <Version 2.0> irqs 0-23 on motherboard > kbd1 at kbdmux0 > cryptosoft0: <software crypto> on motherboard > acpi0: <INTEL DH55TC> on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on > acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 900 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf100-0xf107 mem > 0xfe000000-0xfe3fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0 > pci0: <simple comms> at device 22.0 (no driver attached) > atapci0: <Intel ATA controller> port > 0xf0f0-0xf0f7,0xf0e0-0xf0e3,0xf0d0-0xf0d7,0xf0c0-0xf0c3,0xf0b0-0xf0bf irq 18 > at device 22.2 on pci0 > atapci0: [ITHREAD] > ata2: <ATA channel 0> on atapci0 > ata2: [ITHREAD] > ata3: <ATA channel 1> on atapci0 > ata3: [ITHREAD] > pci0: <simple comms, UART> at device 22.3 (no driver attached) > em0: <Intel(R) PRO/1000 Network Connection 6.9.24> port 0xf040-0xf05f mem > 0xfe400000-0xfe41ffff,0xfe428000-0xfe428fff irq 20 at device 25.0 on pci0 > em0: Using MSI interrupt > em0: [FILTER] > em0: Ethernet address: 00:27:0e:09:5e:00 > ehci0: <Intel PCH USB 2.0 controller USB-B> mem 0xfe427000-0xfe4273ff irq > 16 at device 26.0 on pci0 > ehci0: [ITHREAD] > usbus0: EHCI version 1.0 > usbus0: <Intel PCH USB 2.0 controller USB-B> on ehci0 > pci0: <multimedia, HDA> at device 27.0 (no driver attached) > pcib1: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0 > pci2: <ACPI PCI bus> on pcib2 > ehci1: <Intel PCH USB 2.0 controller USB-A> mem 0xfe426000-0xfe4263ff irq > 23 at device 29.0 on pci0 > ehci1: [ITHREAD] > usbus1: EHCI version 1.0 > usbus1: <Intel PCH USB 2.0 controller USB-A> on ehci1 > pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci3: <ACPI PCI bus> on pcib3 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci1: <Intel AHCI controller> port > 0xf090-0xf097,0xf080-0xf083,0xf070-0xf077,0xf060-0xf063,0xf020-0xf03f mem > 0xfe425000-0xfe4257ff irq 19 at device 31.2 on pci0 > atapci1: [ITHREAD] > atapci1: AHCI v1.30 controller with 6 3Gbps ports, PM not supported > ata4: <ATA channel 0> on atapci1 > ata4: [ITHREAD] > ata5: <ATA channel 1> on atapci1 > ata5: [ITHREAD] > ata6: <ATA channel 2> on atapci1 > ata6: [ITHREAD] > ata7: <ATA channel 3> on atapci1 > ata7: [ITHREAD] > ata8: <ATA channel 4> on atapci1 > ata8: [ITHREAD] > ata9: <ATA channel 5> on atapci1 > ata9: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > acpi_button0: <Power Button> on acpi0 > atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > uart0: [FILTER] > uart0: console (9600,n,8,1) > cpu0: <ACPI CPU> on acpi0 > est0: <Enhanced SpeedStep Frequency Control> on cpu0 > p4tcc0: <CPU Frequency Thermal Control> on cpu0 > cpu1: <ACPI CPU> on acpi0 > est1: <Enhanced SpeedStep Frequency Control> on cpu1 > p4tcc1: <CPU Frequency Thermal Control> on cpu1 > pmtimer0 on isa0 > orm0: <ISA Option ROM> at iomem 0xcd000-0xcdfff pnpid ORM0000 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 > ata0: [ITHREAD] > ata1 at port 0x170-0x177,0x376 irq 15 on isa0 > ata1: [ITHREAD] > Timecounters tick every 1.000 msec > IPsec: Initialized Security Association Processing. > usbus0: 480Mbps High Speed USB v2.0 > usbus1: 480Mbps High Speed USB v2.0 > ad0: 76319MB <Seagate ST380811AS 3.AAE> at ata4-master UDMA100 SATA 1.5Gb/s > SMP: AP CPU #1 Launched! > ugen0.1: <Intel> at usbus0ugen1.1: <Intel> at usbus1 > uhub0: > <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > Root mount waiting for: usbus1 usbus0 > Root mount waiting for: usbus1 usbus0 > uhub0: 3 ports with 3 removable, self powered > uhub1: 3 ports with 3 removable, self powered > Root mount waiting for: usbus1 usbus0 > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on > usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > uhub2: 6 ports with 6 removable, self powered > Root mount waiting for: usbus1 > uhub3: 6 ports with 6 removable, self powered > Trying to mount root from nfs: > NFS ROOT: 10.255.255.1:/usr/home/pxe9/ > > -------------------------------------------------------------------- > Mike Tancsa, tel +1 519 651 3400 > Sentex Communications, mike_at_sentex.net > Providing Internet since 1994 www.sentex.net > Cambridge, Ontario Canada www.sentex.net/mike > >Received on Fri Jan 22 2010 - 16:44:01 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:00 UTC