On Fri, Jul 30, 2010 at 03:05:34PM +0300, Andriy Gapon wrote: > on 30/07/2010 14:57 Anton Shterenlikht said the following: > > On Wed, Jul 28, 2010 at 08:17:47PM +0300, Andriy Gapon wrote: > >> Change it to if (1) { ...}. > > > > did that, and did a cold reboot: > > > > % dmesg | fgrep -i hda > > hdac0: <ATI SB600 High Definition Audio Controller> irq 16 at device 20.2 on pci0 > > hdac0: HDA Driver Revision: 20100226_0142 > > hdac0: [ITHREAD] > > hdac0: hdac_get_capabilities: Invalid corb size (0) > > hdac0: Resetting corb size to 256 > > hdac0: hdac_get_capabilities: Invalid rirb size (0) > > hdac0: Resetting rirb size to 256 > > % > > > > I don't think the device attached. > > No further interesting/related messages after those above? > Could you please try a verbose boot? from a verbose boot: % dmesg | fgrep -i hda hdac0: <ATI SB600 High Definition Audio Controller> irq 16 at device 20.2 on pci0 hdac0: HDA Driver Revision: 20100226_0142 hdac0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xb7fb0000 hdac0: [MPSAFE] hdac0: [ITHREAD] hdac0: hdac_get_capabilities: Invalid corb size (0) hdac0: Resetting corb size to 256 hdac0: hdac_get_capabilities: Invalid rirb size (0) hdac0: Resetting rirb size to 256 hdac0: Caps: OSS 0, ISS 0, BSS 0, NSDO 1, CORB 256, RIRB 256 hdac0: % here's the full /var/run/dmesg.boot from "boot -v": Copyright (c) 1992-2010 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.0-CURRENT #0 r210638M: Fri Jul 30 12:16:29 BST 2010 root_at_mech-aslap239.men.bris.ac.uk:/usr/obj/usr/src/sys/BUZI amd64 WARNING: WITNESS option enabled, expect reduced performance. Table 'FACP' at 0xb7fc8084 Table 'SLIC' at 0xb7fc8220 Table 'EPTH' at 0xb7fc8398 Table 'APIC' at 0xb7fc83d0 Table 'MCFG' at 0xb7fc8434 Table 'TCPA' at 0xb7fc8470 Table 'SSDT' at 0xb7fd98db Table 'SSDT' at 0xb7fd9934 ACPI: No SRAT table found Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff810a8000. Preloaded elf obj module "/boot/kernel/zfs.ko" at 0xffffffff810a8208. Preloaded elf obj module "/boot/kernel/opensolaris.ko" at 0xffffffff810a88b0. Preloaded elf obj module "/boot/kernel/krpc.ko" at 0xffffffff810a8ee0. Preloaded /boot/zfs/zpool.cache "/boot/zfs/zpool.cache" at 0xffffffff810a9508. Calibrating TSC clock ... TSC clock: 1994947870 Hz CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-60 (1994.95-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x60f82 Family = f Model = 68 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x2001<SSE3,CX16> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch> L1 2MB data TLB: 8 entries, fully associative L1 2MB instruction TLB: 8 entries, fully associative L1 4KB data TLB: 32 entries, fully associative L1 4KB instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 2MB unified TLB: 0 entries, disabled/not present L2 4KB data TLB: 512 entries, 4-way associative L2 4KB instruction TLB: 512 entries, 4-way associative L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative real memory = 3221225472 (3072 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages) 0x00000000010d7000 - 0x00000000b2903fff, 2978140160 bytes (727085 pages) avail memory = 2960908288 (2823 MB) Event timer "LAPIC" frequency 0 Hz quality 500 ACPI APIC Table: <HP 0944 > INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 x86bios: IVT 0x000000-0x0004ff at 0xffffff0000000000 x86bios: SSEG 0x010000-0x01ffff at 0xffffff8000010000 x86bios: EBDA 0x09f000-0x09ffff at 0xffffff000009f000 x86bios: ROM 0x0a0000-0x0effff at 0xffffff00000a0000 APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 ULE: setup cpu 0 ULE: setup cpu 1 ACPI: RSDP 0xfe0b0 00024 (v02 HP ) ACPI: XSDT 0xb7fc81bc 00064 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001) ACPI: FACP 0xb7fc8084 000F4 (v04 HP 0944 00000003 HP 00000001) ACPI Error: 32/64X address mismatch in Pm2ControlBlock: 0x00008800/0x0000000000008100, using 32 (20100702/tbfadt-526) ACPI: DSDT 0xb7fc84a4 11437 (v01 HP SB400 00010000 MSFT 03000001) ACPI: FACS 0xb7fe7d80 00040 ACPI: SLIC 0xb7fc8220 00176 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001) ACPI: EPTH 0xb7fc8398 00038 (v01 HP 0944 00000001 HP 00000001) ACPI: APIC 0xb7fc83d0 00062 (v01 HP 0944 00000001 HP 00000001) ACPI: MCFG 0xb7fc8434 0003C (v01 HP 0944 00000001 HP 00000001) ACPI: TCPA 0xb7fc8470 00032 (v02 HP 0944 00000001 HP 00000001) ACPI: SSDT 0xb7fd98db 00059 (v01 HP HPQNLP 00000001 MSFT 03000001) ACPI: SSDT 0xb7fd9934 00206 (v01 HP PSSTBLID 00000001 HP 00000001) MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Changing APIC ID to 2 ioapic0: Routing external 8259A's -> intpin 0 MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: low lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high ioapic0 <Version 2.1> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400 cmci: 0x00000000 firmware: 'iwn6050fw' version 0: 463692 bytes loaded at 0xffffffff80a42184 firmware: 'iwn1000fw' version 0: 335056 bytes loaded at 0xffffffff808aa884 firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xffffffff808fc634 firmware: 'iwn5000fw' version 0: 353240 bytes loaded at 0xffffffff8092a554 firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xffffffff80980a04 wlan: <802.11 Link Layer> firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xffffffff80abe8e4 firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xffffffff80ac09c4 firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xffffffff80ac2aa4 snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024] feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25 firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xffffffff80ac4b84 firmware: 'iwn6000fw' version 0: 454608 bytes loaded at 0xffffffff809d30d4 kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> io: <I/O> null: <null device, zero device> random: <entropy source, Software, Yarrow> CPU0: local APIC error 0x80 acpi0: <HPQOEM SLIC-MPC> on motherboard PCIe: Memory Mapped configuration base _at_ 0xe0000000 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: \\_SB_.C08B.C08C.C08D.C154 -> bus 1 dev 5 func 0 ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48 acpi0: [MPSAFE] acpi0: [ITHREAD] acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: \\_SB_.C08B.C093 -> bus 0 dev 0 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: \\_SB_.C08B.C090 -> bus 0 dev 0 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: \\_SB_.C08B.C09F.C0B2 -> bus 0 dev 20 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: \\_SB_.C08B.C275.C278 -> bus 0 dev 18 func 0 acpi0: Power Button (fixed) acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: \\_SB_.C08B.C096 -> bus 0 dev 0 func 0 unknown: I/O range not supported acpi0: reservation of 0, 8000000 (3) failed acpi0: reservation of 100000, fff00000 (3) failed ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu0: switching to generic Cx mode cpu1: <ACPI CPU> on acpi0 acpi_ec0: <Embedded Controller: GPE 0x11> port 0x62,0x66 on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 9 Validation 0 255 N 0 9 After Disable 0 255 N 0 9 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 10 11 Validation 0 255 N 0 10 11 After Disable 0 255 N 0 10 11 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x1002, dev=0x7910, revid=0x00 domain=0, bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2220, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x7912, revid=0x00 domain=0, bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x7914, revid=0x00 domain=0, bus=0, slot=4, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) powerspec 3 supports D0 D3 current D0 MSI supports 1 message found-> vendor=0x1002, dev=0x7915, revid=0x00 domain=0, bus=0, slot=5, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) powerspec 3 supports D0 D3 current D0 MSI supports 1 message found-> vendor=0x1002, dev=0x4380, revid=0x00 domain=0, bus=0, slot=18, func=0 class=01-01-8f, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0230, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type I/O Port, range 32, base 0x9000, size 3, enabled map[14]: type I/O Port, range 32, base 0x9008, size 2, enabled map[18]: type I/O Port, range 32, base 0x9010, size 3, enabled map[1c]: type I/O Port, range 32, base 0x5018, size 2, enabled map[20]: type I/O Port, range 32, base 0x5020, size 4, enabled map[24]: type Memory, range 32, base 0xcc409000, size 10, enabled pcib0: matched entry for 0.18.INTA pcib0: slot 18 INTA hardwired to IRQ 16 found-> vendor=0x1002, dev=0x4387, revid=0x00 domain=0, bus=0, slot=19, func=0 class=0c-03-10, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[10]: type Memory, range 32, base 0xcc401000, size 12, enabled pcib0: matched entry for 0.19.INTA pcib0: slot 19 INTA hardwired to IRQ 23 found-> vendor=0x1002, dev=0x4388, revid=0x00 domain=0, bus=0, slot=19, func=1 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=5 map[10]: type Memory, range 32, base 0xcc402000, size 12, enabled pcib0: matched entry for 0.19.INTB pcib0: slot 19 INTB hardwired to IRQ 17 found-> vendor=0x1002, dev=0x4389, revid=0x00 domain=0, bus=0, slot=19, func=2 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=5 map[10]: type Memory, range 32, base 0xcc403000, size 12, enabled pcib0: matched entry for 0.19.INTC pcib0: slot 19 INTC hardwired to IRQ 17 found-> vendor=0x1002, dev=0x438a, revid=0x00 domain=0, bus=0, slot=19, func=3 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=5 map[10]: type Memory, range 32, base 0xcc404000, size 12, enabled pcib0: matched entry for 0.19.INTB pcib0: slot 19 INTB hardwired to IRQ 17 found-> vendor=0x1002, dev=0x438b, revid=0x00 domain=0, bus=0, slot=19, func=4 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=5 map[10]: type Memory, range 32, base 0xcc405000, size 12, enabled pcib0: matched entry for 0.19.INTC pcib0: slot 19 INTC hardwired to IRQ 17 found-> vendor=0x1002, dev=0x4386, revid=0x00 domain=0, bus=0, slot=19, func=5 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xcc406000, size 8, enabled pcib0: matched entry for 0.19.INTD pcib0: slot 19 INTD hardwired to IRQ 23 found-> vendor=0x1002, dev=0x4385, revid=0x14 domain=0, bus=0, slot=20, func=0 class=0c-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0003, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type I/O Port, range 32, base 0x8200, size 4, enabled found-> vendor=0x1002, dev=0x438c, revid=0x00 domain=0, bus=0, slot=20, func=1 class=01-01-82, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0220, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 map[20]: type I/O Port, range 32, base 0x5040, size 4, enabled pcib0: matched entry for 0.20.INTA pcib0: slot 20 INTA hardwired to IRQ 16 found-> vendor=0x1002, dev=0x4383, revid=0x00 domain=0, bus=0, slot=20, func=2 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 64, base 0xcc408000, size 14, enabled pcib0: matched entry for 0.20.INTA pcib0: slot 20 INTA hardwired to IRQ 16 found-> vendor=0x1002, dev=0x438d, revid=0x00 domain=0, bus=0, slot=20, func=3 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x4384, revid=0x00 domain=0, bus=0, slot=20, func=4 class=06-04-01, hdrtype=0x01, mfdev=1 cmdreg=0x0027, statreg=0x02a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 domain=0, bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 domain=0, bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 domain=0, bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 domain=0, bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: domain 0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x4000-0x4fff pcib1: memory decode 0xcc200000-0xcc3fffff pcib1: prefetched decode 0xc0000000-0xc7ffffff pci1: <ACPI PCI bus> on pcib1 pci1: domain=0, physical bus=1 found-> vendor=0x1002, dev=0x791f, revid=0x00 domain=0, bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Prefetchable Memory, range 64, base 0xc0000000, size 27, enabled pcib1: requested memory range 0xc0000000-0xc7ffffff: good map[18]: type Memory, range 64, base 0xcc200000, size 16, enabled pcib1: requested memory range 0xcc200000-0xcc20ffff: good map[20]: type I/O Port, range 32, base 0x4000, size 8, enabled pcib1: requested I/O range 0x4000-0x40ff: in range map[24]: type Memory, range 32, base 0xcc300000, size 20, enabled pcib1: requested memory range 0xcc300000-0xcc3fffff: good pcib1: matched entry for 1.5.INTB pcib1: slot 5 INTB hardwired to IRQ 19 vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem 0xc0000000-0xc7ffffff,0xcc200000-0xcc20ffff,0xcc300000-0xcc3fffff irq 19 at device 5.0 on pci1 drm0: <ATI Radeon RS690 X1270 IGP> on vgapci0 vgapci0: attempting to allocate 1 MSI vectors (1 supported) msi: routing MSI IRQ 256 to local APIC 0 vector 49 vgapci0: using IRQ 256 for MSI info: [drm] MSI enabled 1 message(s) vgapci0: child drm0 requested pci_enable_busmaster info: [drm] Initialized radeon 1.31.0 20080613 pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0 pcib2: domain 0 pcib2: secondary bus 16 pcib2: subordinate bus 16 pcib2: I/O decode 0xf000-0xfff pcib2: memory decode 0xcc000000-0xcc0fffff pcib2: no prefetched decode pcib2: could not get PCI interrupt routing table for \\_SB_.C08B.C24F - AE_NOT_FOUND pci16: <ACPI PCI bus> on pcib2 pci16: domain=0, physical bus=16 found-> vendor=0x14e4, dev=0x1713, revid=0x02 domain=0, bus=16, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Memory, range 64, base 0xcc000000, size 16, enabled pcib2: requested memory range 0xcc000000-0xcc00ffff: good pcib0: matched entry for 0.4.INTA pcib0: slot 4 INTA hardwired to IRQ 16 pcib2: slot 0 INTA is routed to irq 16 bge0: <Broadcom BCM5906 A2, ASIC rev. 0x00c002> mem 0xcc000000-0xcc00ffff irq 16 at device 0.0 on pci16 bge0: attempting to allocate 1 MSI vectors (1 supported) msi: routing MSI IRQ 257 to local APIC 0 vector 50 bge0: using IRQ 257 for MSI bge0: CHIP ID 0x0000c002; ASIC REV 0x0c; CHIP REV 0xc0; PCI-E miibus0: <MII bus> on bge0 brgphy0: <BCM5906 10/100baseTX PHY> PHY 1 on miibus0 brgphy0: OUI 0x000af7, model 0x0004, rev. 0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto bge0: bpf attached bge0: Ethernet address: 00:1a:4b:89:4b:4e bge0: [MPSAFE] bge0: [ITHREAD] pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0 pcib3: domain 0 pcib3: secondary bus 32 pcib3: subordinate bus 32 pcib3: I/O decode 0x2000-0x3fff pcib3: memory decode 0xc8000000-0xcbffffff pcib3: no prefetched decode pcib3: could not get PCI interrupt routing table for \\_SB_.C08B.C254 - AE_NOT_FOUND pci32: <ACPI PCI bus> on pcib3 pci32: domain=0, physical bus=32 atapci0: <ATI IXP600 SATA300 controller> port 0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f mem 0xcc409000-0xcc4093ff irq 16 at device 18.0 on pci0 ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 51 atapci0: [MPSAFE] atapci0: [ITHREAD] atapci0: AHCI v1.10 controller with 4 3Gbps ports, PM not supported atapci0: Caps: 64bit NCQ SNTF MPS ALP AL CLO 3Gbps PMD SSC PSC 32cmd CCC 4ports ata2: <ATA channel 0> on atapci0 ata2: AHCI reset... ata2: hardware reset ... ata2: SATA connect time=10ms status=00000113 ata2: ready wait time=19ms ata2: software reset port 0... ata2: ready wait time=0ms ata2: SIGNATURE: 00000101 ata2: AHCI reset done: devices=00000001 ata2: [MPSAFE] ata2: [ITHREAD] ohci0: <OHCI (generic) USB controller> mem 0xcc401000-0xcc401fff irq 23 at device 19.0 on pci0 ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 52 ohci0: [MPSAFE] ohci0: [ITHREAD] usbus0: <OHCI (generic) USB controller> on ohci0 ohci1: <OHCI (generic) USB controller> mem 0xcc402000-0xcc402fff irq 17 at device 19.1 on pci0 ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 53 ohci1: [MPSAFE] ohci1: [ITHREAD] usbus1: <OHCI (generic) USB controller> on ohci1 ohci2: <OHCI (generic) USB controller> mem 0xcc403000-0xcc403fff irq 17 at device 19.2 on pci0 ohci2: [MPSAFE] ohci2: [ITHREAD] usbus2: <OHCI (generic) USB controller> on ohci2 ohci3: <OHCI (generic) USB controller> mem 0xcc404000-0xcc404fff irq 17 at device 19.3 on pci0 ohci3: [MPSAFE] ohci3: [ITHREAD] usbus3: <OHCI (generic) USB controller> on ohci3 ohci4: <OHCI (generic) USB controller> mem 0xcc405000-0xcc405fff irq 17 at device 19.4 on pci0 ohci4: [MPSAFE] ohci4: [ITHREAD] usbus4: <OHCI (generic) USB controller> on ohci4 ehci0: <EHCI (generic) USB 2.0 controller> mem 0xcc406000-0xcc4060ff irq 23 at device 19.5 on pci0 ehci0: [MPSAFE] ehci0: [ITHREAD] ehci0: AMD SB600/700 quirk applied ehci0: Dropped interrupts workaround enabled usbus5: EHCI version 1.0 usbus5: <EHCI (generic) USB 2.0 controller> on ehci0 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci1: <ATI IXP600 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5040-0x504f irq 16 at device 20.1 on pci0 ata0: <ATA channel 0> on atapci1 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=00 stat1=00 devices=0x10000 ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 54 ata0: [MPSAFE] ata0: [ITHREAD] hdac0: <ATI SB600 High Definition Audio Controller> irq 16 at device 20.2 on pci0 hdac0: HDA Driver Revision: 20100226_0142 hdac0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xb7fb0000 hdac0: [MPSAFE] hdac0: [ITHREAD] hdac0: hdac_get_capabilities: Invalid corb size (0) hdac0: Resetting corb size to 256 hdac0: hdac_get_capabilities: Invalid rirb size (0) hdac0: Resetting rirb size to 256 hdac0: Caps: OSS 0, ISS 0, BSS 0, NSDO 1, CORB 256, RIRB 256 isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pcib4: domain 0 pcib4: secondary bus 2 pcib4: subordinate bus 3 pcib4: I/O decode 0xf000-0xfff pcib4: memory decode 0xcc100000-0xcc1fffff pcib4: no prefetched decode pcib4: Subtractively decoded bridge. pci2: <ACPI PCI bus> on pcib4 pci2: domain=0, physical bus=2 found-> vendor=0x1180, dev=0x0476, revid=0xb6 domain=0, bus=2, slot=4, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x80 (32000 ns), maxlat=0x07 (1750 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xcc100000, size 12, enabled pcib4: requested memory range 0xcc100000-0xcc100fff: good pcib4: matched entry for 2.4.INTA pcib4: slot 4 INTA hardwired to IRQ 20 cbb0: <RF5C476 PCI-CardBus Bridge> mem 0xcc100000-0xcc100fff irq 20 at device 4.0 on pci2 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 0 vector 55 cbb0: [MPSAFE] cbb0: [FILTER] cbb0: PCI Configuration space: 0x00: 0x04761180 0x02100007 0x060700b6 0x00824000 0x10: 0xcc100000 0x020000dc 0x20030302 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x07000114 0x40: 0x30c2103c 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x30a00001 0x00000000 0x04630463 0x00000000 0x90: 0x00000000 0x00000000 0x00000000 0x00000000 0xa0: 0x00000008 0x00000000 0x00000000 0x00000000 0xb0: 0x00000000 0xbe000000 0x00003000 0x00000000 0xc0: 0x30c2103c 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0xfe0a0001 0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 battery0: <ACPI Control Method Battery> on acpi0 battery1: <ACPI Control Method Battery> on acpi0 acpi_acad0: <AC Adapter> on acpi0 acpi_button0: <Sleep Button> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 attimer0: [MPSAFE] attimer0: [FILTER] ioapic0: routing intpin 2 (ISA IRQ 0) to lapic 0 vector 56 Event timer "i8254" frequency 1193182 Hz quality 100 atrtc0: <AT realtime clock> port 0x70-0x71,0x72-0x73 irq 8 on acpi0 atrtc0: registered as a time-of-day clock (resolution 1000000us) ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 57 atrtc0: [MPSAFE] atrtc0: [FILTER] Event timer "RTC" frequency 32768 Hz quality 0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 58 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 59 psm0: [GIANT-LOCKED] psm0: [ITHREAD] psm0: model IntelliMouse, device ID 3-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 acpi0: wakeup code va 0xffffff80001f0000 pa 0x4000 isa_probe_children: disabling PnP devices atkbdc: atkbdc0 already exists; skipping it atrtc: atrtc0 already exists; skipping it sc: sc0 already exists; skipping it isa_probe_children: probing non-PnP devices orm0: <ISA Option ROM> at iomem 0xd0000-0xd0fff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: scteken (teken terminal) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0 ppc0 failed to probe at irq 7 on isa0 uart0: <ns8250> failed to probe at port 0x3f8-0x3ff irq 4 on isa0 uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0 isa_probe_children: probing PnP devices acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle0: P_CNT from P_BLK 0x8010 powernow0: <PowerNow! K8> on cpu0 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 powernow1: <PowerNow! K8> on cpu1 Device configuration finished. Reducing kern.maxvnodes 187974 -> 100000 procfs registered ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present; to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf. ZFS filesystem version 4 ZFS storage pool version 15 Timecounter "TSC" frequency 1994947870 Hz quality -100 Starting kernel event timers: LAPIC _at_ 1000Hz, i8254 _at_ 127Hz lapic: Divisor 2, Frequency 99747427 Hz Timecounters tick every 1.000 msec vlan: initialized, using hash tables with chaining IP Filter: v4.1.28 initialized. Default = block all, Logging = enabled lo0: bpf attached ata0: Identifying devices: 00010000 ata0: New devices: 00010000 usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 480Mbps High Speed USB v2.0 acpi_tz0: _AC3: temperature 52.0 >= setpoint 40.0 acpi_tz0: _AC2: temperature 52.0 >= setpoint 50.0 acpi_tz0: switched from NONE to _AC2: 52.0C battery0: battery initialization start ugen0.1: <ATI> at usbus0 uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <ATI> at usbus2 uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 ugen4.1: <ATI> at usbus4 uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <ATI> at usbus5 uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5 battery1: battery initialization start acpi_acad0: acline initialization start ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=80 wire acd0: setting PIO4 acd0: <MATSHITADVD-RAM UJ-861H/1.50> DVDR drive at ata0 as master acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc ata2: Identifying devices: 00000001 ata2: New devices: 00000001 ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire ad4: setting UDMA100 ad4: 152627MB <Seagate ST9160821AS 3.BHE> at ata2-master UDMA100 SATA 1.5Gb/s ad4: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue hdac0: SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400 cmci: 0x00000000 ioapic0: routing intpin 1 (CPU1: local APIC error 0x80ISA IRQ 1 ) to lapic 1 vector 48 ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 1 vector 49 ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 1 vector 50 ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 1 vector 51 msi: Assigning MSI IRQ 257 to local APIC 1 vector 52 WARNING: WITNESS option enabled, expect reduced performance. GEOM: new disk ad4 acpi_acad0: On Line acpi_acad0: acline initialization done, tried 1 times battery0: battery initialization done, tried 1 times acpi_tz0: _AC3: temperature 52.0 >= setpoint 40.0 acpi_tz0: _AC3: temperature 52.0 >= setpoint 40.0 acpi_tz0: switched from _AC2 to _AC3: 52.0C Root mount waiting for: usbus5 usbus4 usbus3 usbus2 usbus1 usbus0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered Event timer "i8254" is dead. Starting kernel event timers: LAPIC _at_ 1000Hz, RTC _at_ 128Hz Root mount waiting for: usbus5 Root mount waiting for: usbus5 Root mount waiting for: usbus5 acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 (probe0:ata0:0:0:0): SCSI status error (probe0:ata0:0:0:0): INQUIRY. CDB: 12 1 0 0 ff 0 (probe0:ata0:0:0:0): CAM status: SCSI Status Error (probe0:ata0:0:0:0): SCSI status: Check Condition (probe0:ata0:0:0:0): SCSI sense: ILLEGAL REQUEST asc:24,0 (Invalid field in CDB) (probe0:ata0:0:0:0): Error 22, Unretryable error (probe0:ata0:0:0:0): Down reving Protocol Version from 2 to 0? Root mount waiting for: usbus5 uhub5: 10 ports with 10 removable, self powered (probe0:ata0:0:0:0): SCSI status error (probe0:ata0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 (probe0:ata0:0:0:0): CAM status: SCSI Status Error (probe0:ata0:0:0:0): SCSI status: Check Condition (probe0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed) (probe0:ata0:0:0:0): Error 6, Unretryable error GEOM: new disk cd0 pass0 at ata0 bus 0 scbus0 target 0 lun 0 pass0: <MATSHITA DVD-RAM UJ-861H 1.50> Removable CD-ROM SCSI-0 device pass0: 16.000MB/s transfers (cd0:ata0:0:0:0): SCSI status error (cd0:ata0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 (cd0:ata0:0:0:0): CAM status: SCSI Status Error (cd0:ata0:0:0:0): SCSI status: Check Condition (cd0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed) (cd0:ata0:0:0:0): Error 6, Unretryable error cd0 at ata0 bus 0 scbus0 target 0 lun 0 cd0: <MATSHITA DVD-RAM UJ-861H 1.50> Removable CD-ROM SCSI-0 device cd0: 16.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed (cd0:ata0:0:0:0): SCSI status error (cd0:ata0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 (cd0:ata0:0:0:0): CAM status: SCSI Status Error (cd0:ata0:0:0:0): SCSI status: Check Condition (cd0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed) (cd0:ata0:0:0:0): Error 6, Unretryable error (cd0:ata0:0:0:0): SCSI status error (cd0:ata0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 (cd0:ata0:0:0:0): CAM status: SCSI Status Error (cd0:ata0:0:0:0): SCSI status: Check Condition (cd0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed) (cd0:ata0:0:0:0): Error 6, Unretryable error Trying to mount root from ufs:/dev/ad4s1a ct_to_ts([2010-07-30 13:57:23]) = 1280498243.000000000 start_init: trying /sbin/init ugen0.2: <Broadcom Corp> at usbus0 ugen1.2: <vendor 0x0430> at usbus1 ums0: <vendor 0x0430 product 0x0100, class 0/0, rev 2.00/1.07, addr 2> on usbus1 ums0: 3 buttons and [XY] coordinates ID=0 bge0: link UP bge0: link state changed to UP -- Anton Shterenlikht Room 2.6, Queen's Building Mech Eng Dept Bristol University University Walk, Bristol BS8 1TR, UK Tel: +44 (0)117 331 5944 Fax: +44 (0)117 929 4423Received on Fri Jul 30 2010 - 11:02:40 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:05 UTC