On 8/14/2011 3:50 PM, C. P. Ghost wrote: > On Thu, Aug 4, 2011 at 2:21 PM, Patrick Lamaiziere > <patfbsd_at_davenulle.org> wrote: >> Hello, >> >> I've tried to update my net5501 running an old FreeBSD-current from >> october to 9.0 beta 1. Unfortunaly installworld crashed and the system >> is broken now : >> >> Instruction interdite(core dumped) >> (instruction interdite => illegal/forbidden instruction) >> >> The world and kernel were built with llvm/clang. > > [CC-ing freebsd-current_at_] > > Is this issue resolved? > > I'm having a bunch of net4801 in production here, > and I was planning to move them to 9.0 soon after > RELEASE. So thanks for the heads up. I'll be holding > back now, and will stay with 8.2-STABLE. > > Unfortunately, I have no spare net4801 (and no net5501) > at the moment, so I can't test BETA on them. :( > >> Could you tell me if it works for you on a net5501? >> Not sure about the 4801, I dont have one online right now. But I netbooted a 5501 and it seems fine. KERNEL is essentially GENERIC minus the debug stuff +option CPU_GEODE +option CPU_SOEKRIS +ident ipsec BTW, watchdog seems to work fine as I just tested that soekris3# cat /var/run/dmesg.boot Copyright (c) 1992-2011 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.0-BETA1 #2: Sun Aug 14 19:15:05 EDT 2011 mdtancsa_at_ich10.sentex.ca:/usr/HEAD/obj/usr/HEAD/src/sys/ipsec i386 ACPI Error: A valid RSDP was not found (20110527/tbxfroot-237) module_register: module pci/xhci already exists! Module pci/xhci failed to register: 17 CPU: Geode(TM) Integrated Processor by AMD PCS (433.26-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x5a2 Family = 5 Model = a Stepping = 2 Features=0x88a93d<FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CLFLUSH,MMX> AMD Features=0xc0400000<MMX+,3DNow!+,3DNow!> real memory = 268435456 (256 MB) avail memory = 247726080 (236 MB) K6-family MTRR support enabled (2 registers) kbd1 at kbdmux0 ACPI Error: A valid RSDP was not found (20110527/tbxfroot-237) ACPI: Table initialisation failed: AE_NOT_FOUND ACPI: Try disabling either ACPI or apic support. cryptosoft0: <software crypto> on motherboard pcib0: <Host to PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 Geode LX: Soekris net5501 comBIOS ver. 1.33 20070103 Copyright (C) 2000-2007 pci0: <encrypt/decrypt, entertainment crypto> at device 1.2 (no driver attached) vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0004000-0xa00040ff irq 11 at device 6.0 on pci0 vr0: Quirks: 0x2 vr0: Revision: 0x96 miibus0: <MII bus> on vr0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr0: Ethernet address: 00:00:24:c9:aa:9c vr1: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0004100-0xa00041ff irq 5 at device 7.0 on pci0 vr1: Quirks: 0x2 vr1: Revision: 0x96 miibus1: <MII bus> on vr1 ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1 ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr1: Ethernet address: 00:00:24:c9:aa:9d vr2: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe300-0xe3ff mem 0xa0004200-0xa00042ff irq 9 at device 8.0 on pci0 vr2: Quirks: 0x2 vr2: Revision: 0x96 miibus2: <MII bus> on vr2 ukphy2: <Generic IEEE 802.3u media interface> PHY 1 on miibus2 ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr2: Ethernet address: 00:00:24:c9:aa:9e vr3: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe400-0xe4ff mem 0xa0004300-0xa00043ff irq 12 at device 9.0 on pci0 vr3: Quirks: 0x2 vr3: Revision: 0x96 miibus3: <MII bus> on vr3 ukphy3: <Generic IEEE 802.3u media interface> PHY 1 on miibus3 ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr3: Ethernet address: 00:00:24:c9:aa:9f isab0: <PCI-ISA bridge> at device 20.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <AMD CS5536 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 20.2 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 ohci0: <OHCI (generic) USB controller> mem 0xa0005000-0xa0005fff irq 15 at device 21.0 on pci0 usbus0: <OHCI (generic) USB controller> on ohci0 ehci0: <AMD CS5536 (Geode) USB 2.0 controller> mem 0xa0006000-0xa0006fff irq 15 at device 21.1 on pci0 usbus1: EHCI version 1.0 usbus1: <AMD CS5536 (Geode) USB 2.0 controller> on ehci0 cpu0 on motherboard pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc8000-0xd27ff pnpid ORM0000 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atrtc0: <AT realtime clock> at port 0x70 irq 8 on isa0 Event timer "RTC" frequency 32768 Hz quality 0 ppc0: parallel port not found. uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 uart0: console (115200,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 Timecounters tick every 0.976 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <AMD> at usbus0 uhub0: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <AMD> at usbus1 uhub1: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 Timecounter "TSC" frequency 433257343 Hz quality 800 Root mount waiting for: usbus1 usbus0 uhub0: 4 ports with 4 removable, self powered Root mount waiting for: usbus1 uhub1: 4 ports with 4 removable, self powered Trying to mount root from nfs: []... NFS ROOT: 10.255.255.1:/home/pxe9 stray irq7 soekris3# -- ------------------- Mike Tancsa, tel +1 519 651 3400 Sentex Communications, mike_at_sentex.net Providing Internet services since 1994 www.sentex.net Cambridge, Ontario Canada http://www.tancsa.com/Received on Sun Aug 14 2011 - 21:27:44 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:16 UTC