El día Saturday, February 26, 2011 a las 01:52:02PM -0500, Eitan Adler escribió: > On Sat, Feb 26, 2011 at 11:58 AM, Matthias Apitz <guru_at_unixarea.de> wrote: > > Could someone please give me a hint how to get the speaker working again? > > Try changing sysctl hw.snd.default_unit=0/1/2 Thanks, but this was my first check as well and does not help. I started to play around with the device.hints(5) config and here is what I figured out: It took me some tine to realize that 'cad0' is the modem, while the real audio is 'cad1'. So I set in device.hints(5): # kenv | fgrep hdac hint.hdac.0.cad1.nid20.config="as=1 seq=15 device=Headphones" hint.hdac.0.cad1.nid28.config="as=2 seq=0 device=Speaker" which is to be seen in the verbose logging on boot as: # dmesg | fgrep hdac | more ... hdac0: Found modem FG nid=1 startnode=2 endnode=38 total=36 hdac0: Probing codec #1... hdac0: HDA Codec #1: Realtek ALC880 hdac0: HDA Codec ID: 0x10ec0880 hdac0: Vendor: 0x10ec hdac0: Device: 0x0880 hdac0: Revision: 0x08 hdac0: Stepping: 0x00 hdac0: PCI Subvendor: 0x107c1734 hdac0: Found audio FG nid=1 startnode=2 endnode=34 total=32 hdac0: hdac0: Processing modem FG cad=0 nid=1... hdac0: hdac0: Processing audio FG cad=1 nid=1... hdac0: GPIO: 0x40000002 NumGPIO=2 NumGPO=0 NumGPI=0 GPIWake=0 GPIUnsol=1 hdac0: nid 20 0x01014010 as 1 seq 0 Line-out Jack jack 1 loc 1 color Green misc 0 hdac0: Patching pin config nid=20 0x01014010 -> 0x0121401f ... hdac0: nid 28 0x411111f0 as 15 seq 0 Speaker None jack 1 loc 1 color Black misc 1 hdac0: Patching pin config nid=28 0x411111f0 -> 0x41111120 i.e. the above device.hints(5) are realized by snd_hda(4); but than it says: hdac0: Patched pins configuration: hdac0: nid 20 0x0121401f as 1 seq 15 Headphones Jack jack 1 loc 1 color Green misc 0 ... hdac0: nid 28 0x41111120 as 2 seq 0 Speaker None jack 1 loc 1 color Black misc 1 [DISABLED] why is 'nid 28' DISABLED? in the user-land the situation is like this: there are 3 mixer (/dev/mixer0..2) and of course I checked if they are all fully up, with one exeption: # mixer -f /dev/mixer2 Recording source: monitor i.e. the recording level can't be controlled, why? there are the following /dev/dsp* devices: # ls /dev/dsp* /dev/dsp0.0 /dev/dsp0.1 /dev/dsp1.0 /dev/dsp2.0 and with Skype (or also just with dd(1)) recording can be done from the device /dev/dsp2 and audio is coming out from /dev/dsp0 (but only through the headphone Jack). What can I do to make the Speaker of the laptop working? The Speaker itself works, for example without any application it just echoes back what from the internal microphone or from the headset micro is coming. Thanks in advance mattias -- Matthias Apitz t +49-89-61308 351 - f +49-89-61308 399 - m +49-170-4527211 e <guru_at_unixarea.de> - w http://www.unixarea.de/Received on Sun Feb 27 2011 - 14:15:29 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:11 UTC