Re: LSI supported mps(4) driver available

From: Dennis Glatting <freebsd_at_penx.com>
Date: Thu, 02 Feb 2012 23:12:36 -0800
FYI. 

I just booted off a RAID1 array using this driver under RELENG_9 (below)
on a Tyan 8812's on-board LSI 2008 chip. I have a second FreeBSD system
with a LSI 9211-8i (IR) but it has a few more days of work before it can
do the same.




mc> dmesg
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-STABLE #1: Thu Feb  2 21:36:16 PST 2012
    root_at_mc:/sys/amd64/compile/SMUNI amd64
CPU: AMD Opteron(TM) Processor 6274                  (2200.07-MHz
K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x600f12  Family = 15  Model = 1
Stepping = 2

Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>

Features2=0x1698220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,AVX>
  AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
  AMD
Features2=0x1c9bfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,NodeId,Topology,<b23>,<b24>>
  TSC: P-state invariant, performance statistics
real memory  = 34359738368 (32768 MB)
avail memory = 33091493888 (31558 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <120911 APIC1027>
FreeBSD/SMP: Multiprocessor System Detected: 32 CPUs
FreeBSD/SMP: 2 package(s) x 16 core(s)
 cpu0 (BSP): APIC ID: 32
 cpu1 (AP): APIC ID: 33
 cpu2 (AP): APIC ID: 34
 cpu3 (AP): APIC ID: 35
 cpu4 (AP): APIC ID: 36
 cpu5 (AP): APIC ID: 37
 cpu6 (AP): APIC ID: 38
 cpu7 (AP): APIC ID: 39
 cpu8 (AP): APIC ID: 40
 cpu9 (AP): APIC ID: 41
 cpu10 (AP): APIC ID: 42
 cpu11 (AP): APIC ID: 43
 cpu12 (AP): APIC ID: 44
 cpu13 (AP): APIC ID: 45
 cpu14 (AP): APIC ID: 46
 cpu15 (AP): APIC ID: 47
 cpu16 (AP): APIC ID: 64
 cpu17 (AP): APIC ID: 65
 cpu18 (AP): APIC ID: 66
 cpu19 (AP): APIC ID: 67
 cpu20 (AP): APIC ID: 68
 cpu21 (AP): APIC ID: 69
 cpu22 (AP): APIC ID: 70
 cpu23 (AP): APIC ID: 71
 cpu24 (AP): APIC ID: 72
 cpu25 (AP): APIC ID: 73
 cpu26 (AP): APIC ID: 74
 cpu27 (AP): APIC ID: 75
 cpu28 (AP): APIC ID: 76
 cpu29 (AP): APIC ID: 77
 cpu30 (AP): APIC ID: 78
 cpu31 (AP): APIC ID: 79
ACPI Warning: Optional field Pm2ControlBlock has zero address or length:
0x0000000000000000/0x1 (20110527/tbfadt-586)
ioapic0 <Version 2.1> irqs 0-23 on motherboard
ioapic1 <Version 2.1> irqs 24-55 on motherboard
kbd1 at kbdmux0
acpi0: <120911 XSDT1027> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of ffffff00, 4000 (3) failed
acpi0: reservation of fec00000, 1000 (3) failed
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fec10000, 20 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, dff00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
cpu8: <ACPI CPU> on acpi0
cpu9: <ACPI CPU> on acpi0
cpu10: <ACPI CPU> on acpi0
cpu11: <ACPI CPU> on acpi0
cpu12: <ACPI CPU> on acpi0
cpu13: <ACPI CPU> on acpi0
cpu14: <ACPI CPU> on acpi0
cpu15: <ACPI CPU> on acpi0
cpu16: <ACPI CPU> on acpi0
cpu17: <ACPI CPU> on acpi0
cpu18: <ACPI CPU> on acpi0
cpu19: <ACPI CPU> on acpi0
cpu20: <ACPI CPU> on acpi0
cpu21: <ACPI CPU> on acpi0
cpu22: <ACPI CPU> on acpi0
cpu23: <ACPI CPU> on acpi0
cpu24: <ACPI CPU> on acpi0
cpu25: <ACPI CPU> on acpi0
cpu26: <ACPI CPU> on acpi0
cpu27: <ACPI CPU> on acpi0
cpu28: <ACPI CPU> on acpi0
cpu29: <ACPI CPU> on acpi0
cpu30: <ACPI CPU> on acpi0
cpu31: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 52 at device 4.0 on pci0
pci7: <ACPI PCI bus> on pcib1
igb0: <Intel(R) PRO/1000 Network Connection version - 2.2.5> port
0xe400-0xe41f mem
0xfeb60000-0xfeb7ffff,0xfeb40000-0xfeb5ffff,0xfeb1c000-0xfeb1ffff irq 44
at device 0.0 on pci7
igb0: Using MSIX interrupts with 9 vectors
igb0: Ethernet address: 00:e0:81:c8:ee:8a
igb1: <Intel(R) PRO/1000 Network Connection version - 2.2.5> port
0xe800-0xe81f mem
0xfebe0000-0xfebfffff,0xfebc0000-0xfebdffff,0xfeb9c000-0xfeb9ffff irq 45
at device 0.1 on pci7
igb1: Using MSIX interrupts with 9 vectors
igb1: Ethernet address: 00:e0:81:c8:ee:8b
pcib2: <ACPI PCI-PCI bridge> irq 53 at device 9.0 on pci0
pci6: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xd800-0xd81f mem
0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 48 at device 0.0 on pci6
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:e0:81:c8:ee:ff
pcib3: <ACPI PCI-PCI bridge> irq 54 at device 11.0 on pci0
pci5: <ACPI PCI bus> on pcib3
mps0: <LSI SAS2008> port 0xc000-0xc0ff mem
0xfe93c000-0xfe93ffff,0xfe940000-0xfe97ffff irq 32 at device 0.0 on pci5
mps0: Firmware: 10.00.02.00, Driver: 11.255.03.00-fbsd
mps0: IOCCapabilities:
1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
pcib4: <ACPI PCI-PCI bridge> irq 54 at device 12.0 on pci0
pci3: <ACPI PCI bus> on pcib4
pcib5: <PCI-PCI bridge> irq 36 at device 0.0 on pci3
pci4: <PCI bus> on pcib5
siis0: <SiI3124 SATA controller> port 0xb800-0xb80f mem
0xfe877c00-0xfe877c7f,0xfe878000-0xfe87ffff irq 36 at device 0.0 on pci4
siisch0: <SIIS channel> at channel 0 on siis0
siisch1: <SIIS channel> at channel 1 on siis0
siisch2: <SIIS channel> at channel 2 on siis0
siisch3: <SIIS channel> at channel 3 on siis0
pcib6: <ACPI PCI-PCI bridge> irq 54 at device 13.0 on pci0
pci2: <ACPI PCI bus> on pcib6
mps1: <LSI SAS2008> port 0xa000-0xa0ff mem
0xfe73c000-0xfe73ffff,0xfe740000-0xfe77ffff irq 40 at device 0.0 on pci2
mps1: Firmware: 10.00.00.00, Driver: 11.255.03.00-fbsd
mps1: IOCCapabilities:
185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
ahci0: <ATI IXP700 AHCI SATA controller> port
0x8000-0x8007,0x7000-0x7003,0x6000-0x6007,0x5000-0x5003,0x4000-0x400f
mem 0xfe6fa400-0xfe6fa7ff irq 22 at device 17.0 on pci0
ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ohci0: <OHCI (generic) USB controller> mem 0xfe6f6000-0xfe6f6fff irq 16
at device 18.0 on pci0
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xfe6f7000-0xfe6f7fff irq 16
at device 18.1 on pci0
usbus1: <OHCI (generic) USB controller> on ohci1
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe6fa800-0xfe6fa8ff irq
17 at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci2: <OHCI (generic) USB controller> mem 0xfe6f8000-0xfe6f8fff irq 18
at device 19.0 on pci0
usbus3: <OHCI (generic) USB controller> on ohci2
ohci3: <OHCI (generic) USB controller> mem 0xfe6f9000-0xfe6f9fff irq 18
at device 19.1 on pci0
usbus4: <OHCI (generic) USB controller> on ohci3
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe6fac00-0xfe6facff irq
19 at device 19.2 on pci0
usbus5: EHCI version 1.0
usbus5: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP700/800 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib7: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci1: <ACPI PCI bus> on pcib7
vgapci0: <VGA-compatible display> port 0x9800-0x987f mem
0xfd800000-0xfdffffff,0xfd7e0000-0xfd7fffff irq 23 at device 9.0 on pci1
ohci4: <OHCI (generic) USB controller> mem 0xfe6fb000-0xfe6fbfff irq 18
at device 20.5 on pci0
usbus6: <OHCI (generic) USB controller> on ohci4
acpi_button0: <Power Button> on acpi0
ipmi0: <IPMI System Interface> port 0xca8,0xcac on acpi0
ipmi0: KCS mode found at io 0xca8 on acpi
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart1: <Non-standard ns8250 class UART with FIFOs> port 0x2f8-0x2ff irq
3 on acpi0
ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xce000-0xcefff,0xcf000-0xcffff,0xd0000-0xd0fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: CGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3d0-0x3db iomem 0xb8000-0xbffff on
isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
AcpiOsExecute: failed to enqueue task, consider increasing the
debug.acpi.max_tasks tunable
acpi_throttle0: <ACPI CPU Throttling> on cpu0
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
(noperiph:siisch0:0:-1:-1): rescan already queued
(noperiph:siisch1:0:-1:-1): rescan already queued
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
usbus6: 12Mbps Full Speed USB v1.0
ugen0.1: <ATI> at usbus0
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
ugen6.1: <ATI> at usbus6
uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
uhub6: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub4: 3 ports with 3 removable, self powered
uhub2: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
ugen5.2: <American Megatrends Inc.> at usbus5
uhub7: <Hub Interface> on usbus5
ipmi0: Timed out waiting for GET_DEVICE_ID
ugen0.2: <BTC> at usbus0
ukbd0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
on usbus0
kbd2 at ukbd0
uhid0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
on usbus0
uhub7: 3 ports with 3 removable, self powered
ugen5.3: <American Megatrends Inc.> at usbus5
ukbd1: <Keyboard Interface> on usbus5
kbd3 at ukbd1
ums0: <Mouse Interface> on usbus5
ums0: 3 buttons and [Z] coordinates ID=0
ugen3.2: <CPS> at usbus3
(probe126:mps1:0:0:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0
(probe126:mps1:0:0:0): CAM status: SCSI Status Error
(probe126:mps1:0:0:0): SCSI status: Check Condition
(probe126:mps1:0:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid
command operation code)
(probe126:mps1:0:0:0): Command Specific Info: 0x5303c0
(probe126:mps1:0:0:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0
(probe126:mps1:0:0:0): CAM status: SCSI Status Error
(probe126:mps1:0:0:0): SCSI status: Check Condition
(probe126:mps1:0:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid
command operation code)
(probe126:mps1:0:0:0): Field Replaceable Unit: 56
(probe126:mps1:0:0:0): Command Specific Info: 0x33353839
da0 at mps1 bus 0 scbus5 target 0 lun 0
da0: <LSI Logical Volume 3000> Fixed Direct Access SCSI-6 device
da0: 150.000MB/s transfers
da0: Command Queueing enabled
da0: 68664MB (140623872 512 byte sectors: 255H 63S/T 8753C)
ada0 at siisch0 bus 0 scbus1 target 0 lun 0
ada0: <OCZ-REVODRIVE 1.20> ATA-8 SATA 2.x device
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
ada1 at siisch1 bus 0 scbus2 target 0 lun 0
ada1: <OCZ-REVODRIVE 1.20> ATA-8 SATA 2.x device
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad6
SMP: AP CPU #1 Launched!
cd0 at ahcich0 bus 0 scbus6 target 0 lun 0
cd0: <HL-DT-ST BD-RE  BH10LS30 1.00> Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SATA 1.x, UDMA6, ATAPI 12bytes, PIO
8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present
- tray closed
SMP: AP CPU #2 Launched!
SMP: AP CPU #12 Launched!
SMP: AP CPU #13 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #20 Launched!
SMP: AP CPU #21 Launched!
SMP: AP CPU #22 Launched!
SMP: AP CPU #23 Launched!
SMP: AP CPU #15 Launched!
SMP: AP CPU #14 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #11 Launched!
SMP: AP CPU #10 Launched!
SMP: AP CPU #9 Launched!
SMP: AP CPU #8 Launched!
SMP: AP CPU #16 Launched!
SMP: AP CPU #17 Launched!
SMP: AP CPU #19 Launched!
SMP: AP CPU #18 Launched!
SMP: AP CPU #31 Launched!
SMP: AP CPU #30 Launched!
SMP: AP CPU #24 Launched!
SMP: AP CPU #25 Launched!
SMP: AP CPU #27 Launched!
SMP: AP CPU #26 Launched!
SMP: AP CPU #29 Launched!
SMP: AP CPU #28 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #7 Launched!
GEOM: ada0: the secondary GPT table is corrupt or invalid.
GEOM: ada0: using the primary only -- recovery suggested.
Trying to mount root from ufs:/dev/da0p2 [rw]...
ZFS filesystem version 5
ZFS storage pool version 28
dragon_saver: the console does not support M_VGA_CG320
module_register_init: MOD_LOAD (dragon_saver, 0xffffffff81768140, 0)
error 19
Received on Fri Feb 03 2012 - 06:12:41 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:23 UTC