Re: Not work ATH (AR9285) after update

From: Adrian Chadd <adrian_at_freebsd.org>
Date: Tue, 23 Jul 2013 06:13:15 -0700
.. are two copies of wpa_supplicant running?



-adrian

On 23 July 2013 06:09, Andrey Fesenko <f0andrey_at_gmail.com> wrote:
> Hello,
> i'm horrible news, after update my notebook not nave wi-fi :(
> full update system, build and install world and kernel.
>
> # uname -a
> FreeBSD x220.local 10.0-CURRENT FreeBSD 10.0-CURRENT #0 r253562: Tue
> Jul 23 14:44:07 MSK 2013
> root_at_x220.local:/usr/obj/usr/src/sys/W_BOOK  amd64
>
> # grep ATH /usr/src/sys/amd64/conf/W_BOOK
> options         ATH_ENABLE_11N
> options         ATH_DEBUG
> options         ATH_DIAGAPI
>
> ath0_at_pci0:3:0:0:        class=0x028000 card=0x1a891a3b chip=0x002b168c
> rev=0x01 hdr=0x00
>     vendor     = 'Atheros Communications Inc.'
>     device     = 'AR9285 Wireless Network Adapter (PCI-Express)'
>     class      = network
>
> # ifconfig
> ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
>         ether 00:25:d3:7b:94:87
>         nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>         media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
>         status: associated
> wlan0: flags=8c43<UP,BROADCAST,RUNNING,OACTIVE,SIMPLEX,MULTICAST>
> metric 0 mtu 1500
>         ether 00:25:d3:7b:94:87
>         inet6 fe80::225:d3ff:fe7b:9487%wlan0 prefixlen 64 scopeid 0x4
>         nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
>         media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>         status: no carrier
>         ssid "" channel 8 (2447 MHz 11g)
>         regdomain 33411 country RU indoor ecm authmode WPA1+WPA2/802.11i
>         privacy MIXED deftxkey UNDEF txpower 20 bmiss 7 scanvalid 60
>         protmode CTS wme burst roaming MANUAL
> # ifconfig wlan0 list scan
> SSID/MESH ID    BSSID              CHAN RATE   S:N     INT CAPS
> APT-SPB2        b8:a3:86:4a:75:6a    6   54M -92:-96  100 EP   HTCAP
> WPA RSN WME WPS
> THD1   74:ea:3a:d1:37:46   10   54M -85:-96  100 EP   RSN HTCAP WME
> Balt1   00:90:4c:c1:00:00    1   54M -90:-96  100 EP   RSN
> TP-LINK_904D2A  64:70:02:90:4d:2a   11   54M -94:-96  100 EPS  RSN
> HTCAP WME ATH WPS
>
> /var/log/messages
> ...
> Jul 23 15:34:24 x220 wpa_supplicant[669]: wlan0: CTRL-EVENT-TERMINATING
> Jul 23 15:34:24 x220 kernel: wlan0: Ethernet address: 00:25:d3:7b:94:87
> Jul 23 15:34:24 x220 devd: Executing '/etc/pccard_ether wlan0 start'
> Jul 23 15:34:24 x220 wpa_supplicant[2563]: Successfully initialized
> wpa_supplicant
> Jul 23 15:34:24 x220 wpa_supplicant[2571]: Successfully initialized
> wpa_supplicant
> Jul 23 15:34:24 x220 wpa_supplicant[2571]: ctrl_iface exists and seems
> to be in use - cannot override it
> Jul 23 15:34:24 x220 wpa_supplicant[2571]: Delete
> '/var/run/wpa_supplicant/wlan0' manually if it is not used anymore
> Jul 23 15:34:24 x220 wpa_supplicant[2571]: Failed to initialize
> control interface '/var/run/wpa_supplicant'. You may have another
> wpa_supplicant process already running or the file was left by an
> unclean termination of wpa_supplicant in which case you will need to
> manually remove this file before starting wpa_supplicant again.
> Jul 23 15:34:24 x220 wpa_supplicant[2571]: ioctl[SIOCS80211, op=26,
> val=0, arg_len=0]: Operation not supported
> Jul 23 15:34:24 x220 wpa_supplicant[2571]: ioctl[SIOCS80211, op=26,
> val=0, arg_len=0]: Operation not supported
> Jul 23 15:34:24 x220 root: /etc/rc.d/wpa_supplicant: WARNING: failed
> to start wpa_supplicant
> Jul 23 15:34:24 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103,
> val=0, arg_len=128]: Operation now in progress
> Jul 23 15:34:24 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan
> Jul 23 15:34:25 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103,
> val=0, arg_len=128]: Operation now in progress
> Jul 23 15:34:25 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan
> Jul 23 15:34:26 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103,
> val=0, arg_len=128]: Operation now in progress
> Jul 23 15:34:26 x220 kernel: ath0: ath_reset_grablock: didn't finish
> after 10 iterations
> Jul 23 15:34:26 x220 kernel: ath0: ath_reset_grablock: warning,
> recursive reset path!
> Jul 23 15:34:26 x220 kernel: ath0: ath_reset: concurrent reset! Danger!
> Jul 23 15:34:26 x220 kernel: ath0: ath_raw_xmit: sc_inreset_cnt > 0; bailing
> Jul 23 15:34:26 x220 kernel: ath0: ath_raw_xmit: sc_inreset_cnt > 0; bailing
> Jul 23 15:34:26 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan
> Jul 23 15:34:27 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103,
> val=0, arg_len=128]: Operation now in progress
> Jul 23 15:34:27 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan
> Jul 23 15:34:29 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103,
> val=0, arg_len=128]: Operation now in progress
> Jul 23 15:34:29 x220 kernel: ath0: ath_reset_grablock: didn't finish
> after 10 iterations
> Jul 23 15:34:29 x220 kernel: ath0: ath_reset_grablock: warning,
> recursive reset path!
> _______________________________________________
> freebsd-current_at_freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"
Received on Tue Jul 23 2013 - 11:13:17 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:39 UTC