Hello, -current members I have a similar problem with Centrino Wireless-N 1000. It operated until r257951 and have a trouble after r258030. I use r262433 kernel with sys/dev/iwn reverted to r257951 and changed from IEEE80211_FC1_WEP to EEE80211_FC1_PROTECTED. r262422 if_iwn module with IWN_DEBUG in opt_iwn.h and dev.iwn.0.debug=1 says: -- output of `dmesg -a` -- iwn0: <Intel Centrino Wireless-N 1000> mem 0xd2500000-0xd2501fff irq 19 at device 0.0 on pci2 wlan0: Ethernet address: 00:1e:64:45:f5:64 iwn0: iwn_setregdomain: invalid channel 8 freq 2447/0x20480 iwn_notif_intr: scanning channel 1 status 1 iwn_notif_intr: scanning channel 6 status 1 iwn_notif_intr: scanning channel 11 status 1 iwn_notif_intr: scanning channel 7 status 1 iwn_notif_intr: scanning channel 13 status 1 iwn_notif_intr: scanning channel 2 status 1 iwn_notif_intr: scanning channel 3 status 1 iwn_notif_intr: scanning channel 4 status 1 iwn_notif_intr: scanning channel 5 status 1 iwn_notif_intr: scanning channel 8 status 1 iwn_notif_intr: scanning channel 9 status 1 iwn_notif_intr: scanning channel 10 status 1 iwn_notif_intr: scanning channel 12 status 1 iwn_tx_data_raw: qid 3 idx 0 len 6 nsegs 1 iwn5000_tx_done: qid 3 idx 0 retries 0 nkill 0 rate 420a duration 778 status 201 iwn_tx_data_raw: qid 3 idx 1 len 86 nsegs 1 iwn5000_tx_done: qid 3 idx 1 retries 0 nkill 0 rate 420a duration 1418 status 201 iwn_set_link_quality: 1stream antenna=0x01, 2stream antenna=0x03, ntxstreams=1 iwn_set_link_quality: i=0, txrate=7, rate=0x87 iwn_set_link_quality: i=1, txrate=6, rate=0x86 iwn_set_link_quality: i=2, txrate=5, rate=0x85 iwn_set_link_quality: i=3, txrate=4, rate=0x84 iwn_set_link_quality: i=4, txrate=3, rate=0x83 iwn_set_link_quality: i=5, txrate=2, rate=0x82 iwn_set_link_quality: i=6, txrate=1, rate=0x81 iwn_set_link_quality: i=7, txrate=0, rate=0x80 iwn_set_link_quality: i=8, txrate=0, rate=0x80 iwn_set_link_quality: i=9, txrate=0, rate=0x80 iwn_set_link_quality: i=10, txrate=0, rate=0x80 iwn_set_link_quality: i=11, txrate=0, rate=0x80 iwn_set_link_quality: i=12, txrate=0, rate=0x80 iwn_set_link_quality: i=13, txrate=0, rate=0x80 iwn_set_link_quality: i=14, txrate=0, rate=0x80 iwn_set_link_quality: i=15, txrate=0, rate=0x80 wlan0: link state changed to UP iwn0: iwn_intr: fatal firmware error firmware error log: error type = "SYSASSERT" (0x00000005) program counter = 0x00018DBC source line = 0x00000032 error data = 0x0000000100000000 branch link = 0x00018D6E00018D6E interrupt link = 0x0000082600000000 time = 1043083265 driver status: tx ring 0: qid=0 cur=0 queued=0 tx ring 1: qid=1 cur=0 queued=0 tx ring 2: qid=2 cur=0 queued=0 tx ring 3: qid=3 cur=2 queued=0 tx ring 4: qid=4 cur=57 queued=0 tx ring 5: qid=5 cur=0 queued=0 tx ring 6: qid=6 cur=0 queued=0 tx ring 7: qid=7 cur=0 queued=0 tx ring 8: qid=8 cur=0 queued=0 tx ring 9: qid=9 cur=0 queued=0 tx ring 10: qid=10 cur=0 queued=0 tx ring 11: qid=11 cur=0 queued=0 tx ring 12: qid=12 cur=0 queued=0 tx ring 13: qid=13 cur=0 queued=0 tx ring 14: qid=14 cur=0 queued=0 tx ring 15: qid=15 cur=0 queued=0 tx ring 16: qid=16 cur=0 queued=0 tx ring 17: qid=17 cur=0 queued=0 tx ring 18: qid=18 cur=0 queued=0 tx ring 19: qid=19 cur=0 queued=0 rx ring: cur=55 -- output of `pciconf -lvcb` -- iwn0_at_pci0:2:0:0: class=0x028000 card=0x13058086 chip=0x00838086 rev=0x00 hdr=0x00 vendor = 'Intel Corporation' device = 'Centrino Wireless-N 1000 [Condor Peak]' class = network bar [10] = type Memory, range 64, base 0xd2500000, size 8192, enabled cap 01[c8] = powerspec 3 supports D0 D3 current D0 cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message cap 10[e0] = PCI-Express 1 endpoint max data 128(128) FLR link x1(x1) speed 2.5(2.5) ASPM L1(L0s/L1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 3 corrected ecap 0003[140] = Serial 1 001e64ffff45f564 -- Kaho ToshikazuReceived on Fri Feb 28 2014 - 00:48:04 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:47 UTC