The only recent ATAPI change I recall is 270327, does it still occur if you revert that? Regards Steve ----- Original Message ----- From: "Mike." <the.lists_at_mgm51.com> > > > I'm starting to look at FreeBSD 11-current to see what's coming soon. > I have an older notebook that I use for test environments for > purposes such as this. Unfortunately, the notebook won't boot up > from the install CD, there's a loop it cannot seem to get out of. > > > > Details are: > > - The install CD was made from this image: > FreeBSD-11.0-CURRENT-i386-20140918-r271779-disc1 > > - The dmesg for the notebook is at the end of this message. The > dmesg was captured with FreeBSD 10.0. In the dmesg, you can see the > following lines: > > (aprobe0:ata1:0:1:0): ATAPI_IDENTIFY. ACB: a1 00 00 00 00 40 00 00 00 > 00 00 00 > (aprobe0:ata1:0:1:0): CAM status: Command timeout > (aprobe0:ata1:0:1:0): Error 5, Retry was blocked > run_interrupt_driven_hooks: still waiting after 60 seconds for > xpt_config > (aprobe0:ata1:0:1:0): ATAPI_IDENTIFY. ACB: a1 00 00 00 00 40 00 00 00 > 00 00 00 > (aprobe0:ata1:0:1:0): CAM status: Command timeout > (aprobe0:ata1:0:1:0): Error 5, Retry was blocked > > > which, while slowing down the boot process drastically, still allowed > the boot process to run to successful completion. > > > - When I try to boot using the FreeBSD 11-current install CD, that > loop seems to go on ad infinitum, or at least for the 5 minutes until > I gave up. I cannot post a dmesg from that boot-up because I never > got to a prompt. However, I did take a couple of pictures of the > offending screens. They are here: > http://archive.mgm51.com/cache/fbsd-11-current-01.jpg > http://archive.mgm51.com/cache/fbsd-11-current-02.jpg > The first image shows the start of the looping, and the second shows > the continuation. > > > While this notebook is used only for testing, it is important to me > in that aspect. How can I get around this looping issue? > > Please let me know if there's any additional info you need. > > Thanks. > > > > > > And now, the dmesg... > > Copyright (c) 1992-2014 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, > 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 10.0-RELEASE-p8 #1 r271323: Wed Sep 10 20:25:45 EDT 2014 > root_at_a31pf.245l.home:/usr/obj/usr/src/sys/GENERIC i386 > FreeBSD clang version 3.3 (tags/RELEASE_33/final 183502) 20130610 > CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.70GHz (1698.60-MHz 686-class > CPU) > Origin = "GenuineIntel" Id = 0xf24 Family = 0xf Model = 0x2 > Stepping = 4 > Features=0x3febf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE, > MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM> > real memory = 1073741824 (1024 MB) > avail memory = 1029230592 (981 MB) > kbd1 at kbdmux0 > random: <Software, Yarrow> initialized > acpi0: <IBM TP-1G> on motherboard > acpi_ec0: <Embedded Controller: GPE 0x1c, ECDT> port 0x62,0x66 on > acpi0 > acpi0: Power Button (fixed) > acpi0: reservation of 0, a0000 (3) failed > acpi0: reservation of 100000, 3ff00000 (3) failed > cpu0: <ACPI CPU> on acpi0 > attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 > Timecounter "i8254" frequency 1193182 Hz quality 0 > Event timer "i8254" frequency 1193182 Hz quality 100 > atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 > Event timer "RTC" frequency 32768 Hz quality 0 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on > acpi0 > acpi_lid0: <Control Method Lid Switch> on acpi0 > acpi_button0: <Sleep Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <Intel 82845 host to AGP bridge> on hostb0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem > 0xe8000000-0xefffffff,0xd0100000-0xd010ffff irq 11 at device 0.0 on > pci1 > vgapci0: Boot video device > uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port > 0x1800-0x181f irq 11 at device 29.0 on pci0 > usbus0 on uhci0 > uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port > 0x1820-0x183f irq 11 at device 29.1 on pci0 > usbus1 on uhci1 > uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port > 0x1840-0x185f irq 11 at device 29.2 on pci0 > usbus2 on uhci2 > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > cbb0: <RF5C476 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 11 > at device 0.0 on pci2 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > cbb1: <RF5C476 PCI-CardBus Bridge> mem 0x50100000-0x50100fff irq 11 > at device 0.1 on pci2 > cardbus1: <CardBus bus> on cbb1 > pccard1: <16-bit PCCard bus> on cbb1 > pci2: <serial bus, FireWire> at device 0.2 (no driver attached) > fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x8000-0x803f > mem 0xd0200000-0xd0200fff irq 11 at device 8.0 on pci2 > miibus0: <MII bus> on fxp0 > inphy0: <i82562ET 10/100 media interface> PHY 1 on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, > auto-flow > fxp0: Ethernet address: 00:0e:9b:2c:d3:f6 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH3 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on > pci0 > ata0: <ATA channel> at channel 0 on atapci0 > ata1: <ATA channel> at channel 1 on atapci0 > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > pcm0: <Intel ICH3 (82801CA)> port 0x1c00-0x1cff,0x18c0-0x18ff irq 11 > at device 31.5 on pci0 > pcm0: <Analog Devices AD1881A AC97 Codec> > pci0: <simple comms, generic modem> at device 31.6 (no driver > attached) > acpi_tz0: <Thermal Zone> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: [GIANT-LOCKED] > psm0: model Generic PS/2 mouse, device ID 0 > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on > acpi0 > battery0: <ACPI Control Method Battery> on acpi0 > acpi_acad0: <AC Adapter> on acpi0 > pmtimer0 on isa0 > orm0: <ISA Option ROMs> at iomem > 0xc0000-0xcffff,0xd0000-0xd0fff,0xd1000-0xd1fff,0xdc000-0xdffff,0xe000 > 0-0xeffff pnpid ORM0000 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on > isa0 > ppc0: parallel port not found. > acpi_perf0: <ACPI CPU Frequency Control> on cpu0 > p4tcc0: <CPU Frequency Thermal Control> on cpu0 > Timecounters tick every 1.000 msec > random: unblocking device. > usbus0: 12Mbps Full Speed USB v1.0 > usbus1: 12Mbps Full Speed USB v1.0 > usbus2: 12Mbps Full Speed USB v1.0 > ugen2.1: <Intel> at usbus2 > uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on > usbus2 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on > usbus1 > ugen0.1: <Intel> at usbus0 > uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on > usbus0 > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > uhub2: 2 ports with 2 removable, self powered > ath0: <Atheros 5212> irq 11 at device 0.0 on cardbus1 > ath0: AR5212 mac 5.6 RF5112 phy 4.1 > ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0036 > (aprobe0:ata1:0:1:0): ATAPI_IDENTIFY. ACB: a1 00 00 00 00 40 00 00 00 > 00 00 00 > (aprobe0:ata1:0:1:0): CAM status: Command timeout > (aprobe0:ata1:0:1:0): Error 5, Retry was blocked > run_interrupt_driven_hooks: still waiting after 60 seconds for > xpt_config > (aprobe0:ata1:0:1:0): ATAPI_IDENTIFY. ACB: a1 00 00 00 00 40 00 00 00 > 00 00 00 > (aprobe0:ata1:0:1:0): CAM status: Command timeout > (aprobe0:ata1:0:1:0): Error 5, Retry was blocked > ada0 at ata0 bus 0 scbus0 target 0 lun 0 > ada0: <HTS721080G9AT00 MC4OA51A> ATA-6 device > ada0: Serial Number MPC412Y4G6J1AE > ada0: 100.000MB/s transfers (UDMA5, PIO 8192bytes) > ada0: 76319MB (156301488 512 byte sectors: 16H 63S/T 16383C) > ada0: Previously was known as ad0 > cd0 at ata1 bus 0 scbus1 target 0 lun 0 > cd0: <MATSHITA UJDA720 DVD/CDRW 1.03> Removable CD-ROM SCSI-0 device > cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes) > cd0: Attempt to query device size failed: NOT READY, Medium not > present - tray closed > Trying to mount root from ufs:/dev/ada0p2 [rw]... > wlan0: Ethernet address: 00:04:e2:b6:d4:d6 > > > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org" >Received on Sun Sep 28 2014 - 14:01:59 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:52 UTC
