Dear all, on a 11-current system I tried a VERBATIM usb drive which does not produce a /dev/da... entry. My question is whether this can be fixed by adding an entry in some array within the kernel source (header files?) or is this bad hardware for which a workaround implementation is needed. system is FreeBSD 11.0-CURRENT (VENUS) #0 r280370: Mon Mar 23 22:14:14 CET 2015 relevant dmesg entries when inserting the drive: umass0: <Verbatim STORE N GO, class 0/0, rev 2.10/1.00, addr 2> on usbus2 umass0: SCSI over Bulk-Only; quirks = 0x8100 umass0:4:0: Attached to scbus4 (probe0:umass-sim0:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe0:umass-sim0:0:0:0): CAM status: Auto-Sense Retrieval Failed (probe0:umass-sim0:0:0:0): Error 5, Unretryable error (da0:umass-sim0:0:0:0): got CAM status 0x50 (da0:umass-sim0:0:0:0): fatal error, failed to attach to device the device gets recognized as ugen2.2 as seen by the timestamp below # ls -ld ug* lrwxr-xr-x 1 root wheel 9 Mar 28 13:41 ugen0.1_at_ -> usb/0.1.0 lrwxr-xr-x 1 root wheel 9 Mar 28 13:41 ugen1.1_at_ -> usb/1.1.0 lrwxr-xr-x 1 root wheel 9 Mar 28 13:41 ugen2.1_at_ -> usb/2.1.0 lrwxr-xr-x 1 root wheel 9 Mar 28 13:44 ugen2.2_at_ -> usb/2.2.0 ... and of course usbconfig writes the ugen2.2 configuration ugen2.2: <STORE N GO Verbatim> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (2mA) what follows is the full dmesg output, and the complete usbconfig output what do you recommend? Best wishes Damian -------------------------------------------------- Copyright (c) 1992-2015 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.0-CURRENT #0 r280370: Mon Mar 23 22:14:14 CET 2015 root_at_venus.local:/usr/obj/usr/src/sys/VENUS amd64 FreeBSD clang version 3.6.0 (tags/RELEASE_360/final 230434) 20150225 WARNING: WITNESS option enabled, expect reduced performance. CPU: Intel(R) Core(TM)2 CPU 6300 _at_ 1.86GHz (1862.06-MHz K8-class CPU) Origin="GenuineIntel" Id=0x6f2 Family=0x6 Model=0xf Stepping=2 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> VT-x: HLT,PAUSE TSC: P-state invariant, performance statistics real memory = 2147483648 (2048 MB) avail memory = 2038140928 (1943 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <PTLTD APIC > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 2.0> irqs 0-23 on motherboard random: entropy device infrastructure driver random: selecting highest priority adaptor <Dummy> kbd1 at kbdmux0 netmap: loaded module random: SOFT: yarrow init() random: selecting highest priority adaptor <Yarrow> acpi0: <PTLTD RSDT> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 450 Event timer "HPET1" frequency 14318180 Hz quality 440 Event timer "HPET2" frequency 14318180 Hz quality 440 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 vgapci0: <VGA-compatible display> mem 0xd1000000-0xd1ffffff,0xc0000000-0xcfffffff,0xd0000000-0xd0ffffff irq 16 at device 0.0 on pci1 vgapci0: Boot video device uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x1820-0x183f irq 20 at device 26.0 on pci0 usbus0 on uhci0 uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x1840-0x185f irq 18 at device 26.1 on pci0 usbus1 on uhci1 ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xd2305000-0xd23053ff irq 18 at device 26.7 on pci0 usbus2: EHCI version 1.0 usbus2 on ehci0 hdac0: <Intel 82801H HDA Controller> mem 0xd2300000-0xd2303fff irq 20 at device 27.0 on pci0 pcib2: <ACPI PCI-PCI bridge> irq 23 at device 28.0 on pci0 pcib2: failed to allocate initial I/O port window: 0-0xfff pcib2: failed to allocate initial memory window: 0-0xfffff pcib2: failed to allocate initial prefetch window: 0-0xfffff pci3: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> irq 21 at device 28.5 on pci0 pci9: <ACPI PCI bus> on pcib3 bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x00a002> mem 0xd2000000-0xd200ffff irq 17 at device 0.0 on pci9 bge0: CHIP ID 0x0000a002; ASIC REV 0x0a; CHIP REV 0xa0; PCI-E miibus0: <MII bus> on bge0 brgphy0: <BCM5755 1000BASE-T media interface> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge0: Using defaults for TSO: 65518/35/2048 bge0: Ethernet address: 00:30:05:c2:d9:9e uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x1860-0x187f irq 23 at device 29.0 on pci0 usbus3 on uhci2 uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x1880-0x189f irq 22 at device 29.1 on pci0 usbus4 on uhci3 uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x18a0-0x18bf irq 21 at device 29.2 on pci0 usbus5 on uhci4 ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xd2305400-0xd23057ff irq 23 at device 29.7 on pci0 usbus6: EHCI version 1.0 usbus6 on ehci1 pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci12: <ACPI PCI bus> on pcib4 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH8 SATA300 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18f0-0x18ff,0x18e0-0x18ef at device 31.2 on pci0 ata0: <ATA channel> at channel 0 on atapci0 ata1: <ATA channel> at channel 1 on atapci0 atapci1: <Intel ICH8 SATA300 controller> port 0x1c48-0x1c4f,0x1c3c-0x1c3f,0x1c40-0x1c47,0x1c38-0x1c3b,0x1c10-0x1c1f,0x1c00-0x1c0f irq 22 at device 31.5 on pci0 ata2: <ATA channel> at channel 0 on atapci1 ata3: <ATA channel> at channel 1 on atapci1 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fd0: <1440-KB 3.5" drive> on fdc0 drive 0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xcefff,0xcf000-0xcffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] ppc0: cannot reserve I/O port range est0: <Enhanced SpeedStep Frequency Control> on cpu0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 usbus0: 12Mbps Full Speed USB v1.0 Timecounters tick every 1.000 msec hdacc0: <Realtek ALC260 HDA CODEC> at cad 2 on hdac0 hdaa0: <Realtek ALC260 Audio Function Group> at nid 1 on hdacc0 pcm0: <Realtek ALC260 (Analog 2.0+HP/2.0)> at nid 15,21 and 18,20,19 on hdaa0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 480Mbps High Speed USB v2.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 480Mbps High Speed USB v2.0 ugen2.1: <Intel> at usbus2 ugen1.1: <Intel> at usbus1 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen0.1: <Intel> at usbus0 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen5.1: <Intel> at usbus5 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 ugen4.1: <Intel> at usbus4 ugen3.1: <Intel> at usbus3 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 ugen6.1: <Intel> at usbus6 uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6 uhub5: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2 uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub5: 4 ports with 4 removable, self powered ada0 at ata0 bus 0 scbus0 target 0 lun 0 ada0: <ST3250820AS 3.AAC> ATA-7 SATA 2.x device ada0: Serial Number 9QE1G37L ada0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes) ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad0 random: unblocking device. SMP: AP CPU #1 Launched! Timecounter "TSC" frequency 1862059941 Hz quality 1000 WARNING: WITNESS option enabled, expect reduced performance. Root mount waiting for: usbus6 uhub4: 6 ports with 6 removable, self powered Trying to mount root from ufs:/dev/ada0p2 [rw]... ugen4.2: <Fujitsu Siemens Computers> at usbus4 ukbd0: <Fujitsu Siemens Computers Fujitsu Siemens Computers USB-Keyboard rf v1.0, class 0/0, rev 1.10/0.01, addr 2> on usbus4 kbd2 at ukbd0 uhid0: <Fujitsu Siemens Computers Fujitsu Siemens Computers USB-Keyboard rf v1.0, class 0/0, rev 1.10/0.01, addr 2> on usbus4 ugen2.2: <Verbatim> at usbus2 umass0: <Verbatim STORE N GO, class 0/0, rev 2.10/1.00, addr 2> on usbus2 umass0: SCSI over Bulk-Only; quirks = 0x8100 umass0:4:0: Attached to scbus4 (probe0:umass-sim0:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00 (probe0:umass-sim0:0:0:0): CAM status: Auto-Sense Retrieval Failed (probe0:umass-sim0:0:0:0): Error 5, Unretryable error (da0:umass-sim0:0:0:0): got CAM status 0x50 (da0:umass-sim0:0:0:0): fatal error, failed to attach to device usbconfig ugen2.1: <EHCI root HUB Intel> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.1: <UHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen0.1: <UHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen5.1: <UHCI root HUB Intel> at usbus5, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen4.1: <UHCI root HUB Intel> at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen3.1: <UHCI root HUB Intel> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen6.1: <EHCI root HUB Intel> at usbus6, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen4.2: <Fujitsu Siemens Computers USB-Keyboard rf v1.0 Fujitsu Siemens Computers> at usbus4, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA) ugen2.2: <STORE N GO Verbatim> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (2mA)Received on Sat Mar 28 2015 - 13:06:28 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:56 UTC