Re: after update to r292778 no interface ath0 and wlan0

it's there; just not called ath0

sysctl net.wlan.devices

and just create it - ifconfig wlan0 create wlandev ath0

You need to update your /etc for it all to work again out of the box. :)


-a


On 6 January 2016 at 17:49, Matthias Apitz <guru_at_unixarea.de> wrote:
>
> Hello,
>
> I have updated my Acer C720 netbook (amd64) from r285885 to r292778 and
> now I do not see any network devices; the kernel is just GENERIC;
>
> the lines in /etc/rc.conf are
>
> wlans_ath0="wlan0"
> ifconfig_wlan0="WPA DHCP"
>
> (i.e. unchanged as they worked before); in dmesg the aht0 is shown as
> usual with:
>
> ath0: <Atheros AR946x/AR948x> mem 0xe0400000-0xe047ffff at device 0.0 on pci1
> ath0: [HT] enabling HT modes
> ath0: [HT] enabling short-GI in 20MHz mode
> ath0: [HT] 1 stream STBC receive enabled
> ath0: [HT] 1 stream STBC transmit enabled
> ath0: [HT] 2 RX streams; 2 TX streams
> ath0: AR9460 mac 640.2 RF5110 phy 48.10
> ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
>
> The full dmesg is attached. What do I missed as changes in CURRENT?
> Thanks
>
>         matthias
>
>
>
> Copyright (c) 1992-2015 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 11.0-CURRENT #0 r292778: Mon Dec 28 05:45:37 CET 2015
>     root_at_poudriere-amd64:/usr/local/r292778/obj/usr/local/r292778/src/sys/GENERIC amd64
> FreeBSD clang version 3.7.1 (tags/RELEASE_371/final 255217) 20151225
> WARNING: WITNESS option enabled, expect reduced performance.
> VT(vga): resolution 640x480
> CPU: Intel(R) Celeron(R) 2955U _at_ 1.40GHz (1396.80-MHz K8-class CPU)
>   Origin="GenuineIntel"  Id=0x40651  Family=0x6  Model=0x45  Stepping=1
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x4ddaebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,XSAVE,OSXSAVE,RDRAND>
>   AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
>   AMD Features2=0x21<LAHF,ABM>
>   Structured Extended Features=0x2603<FSGSBASE,TSCADJ,ERMS,INVPCID,NFPUSG>
>   XSAVE Features=0x1<XSAVEOPT>
>   VT-x: (disabled in BIOS) PAT,HLT,MTF,PAUSE,EPT,UG,VPID
>   TSC: P-state invariant, performance statistics
> real memory  = 4301258752 (4102 MB)
> avail memory = 1917681664 (1828 MB)
> Event timer "LAPIC" quality 600
> ACPI APIC Table: <CORE   COREBOOT>
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> FreeBSD/SMP: 1 package(s) x 2 core(s)
>  cpu0 (BSP): APIC ID:  0
>  cpu1 (AP): APIC ID:  2
> random: unblocking device.
> ioapic0 <Version 2.0> irqs 0-39 on motherboard
> random: entropy device external interface
> kbd1 at kbdmux0
> netmap: loaded module
> module_register_init: MOD_LOAD (vesa, 0xffffffff80ee1ed0, 0) error 19
> random: registering fast source Intel Secure Key RNG
> random: fast provider: "Intel Secure Key RNG"
> vtvga0: <VT VGA driver> on motherboard
> cryptosoft0: <software crypto> on motherboard
> acpi0: <CORE COREBOOT> on motherboard
> acpi0: Power Button (fixed)
> Timecounter "HPET" frequency 14318180 Hz quality 950
> Event timer "HPET" frequency 14318180 Hz quality 550
> Event timer "HPET1" frequency 14318180 Hz quality 440
> Event timer "HPET2" frequency 14318180 Hz quality 440
> Event timer "HPET3" frequency 14318180 Hz quality 440
> Event timer "HPET4" frequency 14318180 Hz quality 440
> Event timer "HPET5" frequency 14318180 Hz quality 440
> Event timer "HPET6" frequency 14318180 Hz quality 440
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
> Event timer "RTC" frequency 32768 Hz quality 0
> attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Event timer "i8254" frequency 1193182 Hz quality 100
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
> acpi_ec0: <Embedded Controller: GPE 0x24> port 0x62,0x66 on acpi0
> acpi_lid0: <Control Method Lid Switch> on acpi0
> acpi_button0: <Power Button> on acpi0
> acpi_button1: <Sleep Button> irq 37 on acpi0
> acpi_button2: <Sleep Button> irq 38 on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> vgapci0: <VGA-compatible display> port 0x1800-0x183f mem 0xe0000000-0xe03fffff,0xd0000000-0xdfffffff at device 2.0 on pci0
> vgapci0: Boot video device
> hdac0: <Intel Haswell HDA Controller> mem 0xe0510000-0xe0513fff at device 3.0 on pci0
> xhci0: <Intel Panther Point USB 3.0 controller> mem 0xe0500000-0xe050ffff at device 20.0 on pci0
> xhci0: 32 bytes context size, 64-bit DMA
> xhci0: Port routing mask set to 0xffffffff
> usbus0 on xhci0
> pci0: <base peripheral, DMA controller> at device 21.0 (no driver attached)
> ig4iic0: <Intel Lynx Point-LP I2C Controller-1> mem 0xe051a000-0xe051afff,0xe051b000-0xe051bfff at device 21.1 on pci0
> ig4iic0: Using MSI
> ig4iic1: <Intel Lynx Point-LP I2C Controller-2> mem 0xe051c000-0xe051cfff,0xe051d000-0xe051dfff at device 21.2 on pci0
> ig4iic1: Using MSI
> hdac1: <Intel Lynx Point-LP HDA Controller> mem 0xe0514000-0xe0517fff at device 27.0 on pci0
> pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> ath0: <Atheros AR946x/AR948x> mem 0xe0400000-0xe047ffff at device 0.0 on pci1
> ar9300_attach: calling ar9300_hw_attach
> ar9300_hw_attach: calling ar9300_eeprom_attach
> ar9300_flash_map: unimplemented for now
> Restoring Cal data from DRAM
> Restoring Cal data from EEPROM
> Restoring Cal data from Flash
> Restoring Cal data from Flash
> Restoring Cal data from OTP
> ar9300_hw_attach: ar9300_eeprom_attach returned 0
> ath0: [HT] enabling HT modes
> ath0: [HT] enabling short-GI in 20MHz mode
> ath0: [HT] 1 stream STBC receive enabled
> ath0: [HT] 1 stream STBC transmit enabled
> ath0: [HT] 2 RX streams; 2 TX streams
> ath0: AR9460 mac 640.2 RF5110 phy 48.10
> ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
> ehci0: <Intel Lynx Point LP USB 2.0 controller USB> mem 0xe051f800-0xe051fbff at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci0
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <Intel Lynx Point-LP AHCI SATA controller> port 0x1860-0x1867,0x1870-0x1873,0x1868-0x186f,0x1874-0x1877,0x1840-0x185f mem 0xe051f000-0xe051f7ff irq 22 at device 31.2 on pci0
> ahci0: AHCI v1.30 with 2 6Gbps ports, Port Multiplier not supported
> ahcich0: <AHCI channel> at channel 0 on ahci0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_acad0: <AC Adapter> on acpi0
> battery0: <ACPI Control Method Battery> on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> ppc0: cannot reserve I/O port range
> coretemp0: <CPU On-Die Thermal Sensors> on cpu0
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> coretemp1: <CPU On-Die Thermal Sensors> on cpu1
> est1: <Enhanced SpeedStep Frequency Control> on cpu1
> Timecounters tick every 1.000 msec
> IPsec: Initialized Security Association Processing.
> IP Filter: v5.1.2 initialized.  Default = pass all, Logging = enabled
> hdacc0: <Intel Haswell HDA CODEC> at cad 0 on hdac0
> hdaa0: <Intel Haswell Audio Function Group> at nid 1 on hdacc0
> pcm0: <Intel Haswell (HDMI/DP 8ch)> at nid 3 on hdaa0
> smbus0: <System Management Bus> on ig4iic0
> usbus0: 5.0Gbps Super Speed USB v3.0
> usbus1: 480Mbps High Speed USB v2.0
> ugen0.1: <0x8086> at usbus0
> uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> uhub0: 13 ports with 13 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <NC.21411.02440728772LM0001> at usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub2: <vendor 0x8087 product 0x8000, class 9/0, rev 2.00/0.04, addr 2> on usbus1
> cyapa0: <Cypress APA I2C Trackpad> at addr 0x67 on smbus0
> cyapa0: cyapa init status 8b
> cyapa0: CYTRA-103006-00 buttons=LM- res=870x470
> smbus1: <System Management Bus> on ig4iic1
> uhub2: 8 ports with 8 removable, self powered
> isl0: <ISL Digital Ambient Light Sensor> at addr 0x44 on smbus1
> hdacc1: <Realtek (0x0283) HDA CODEC> at cad 0 on hdac1
> hdaa1: <Realtek (0x0283) Audio Function Group> at nid 1 on hdacc1
> pcm1: <Realtek (0x0283) (Analog 2.0+HP/4ch)> at nid 20,33 and 25,26 on hdaa1
> usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT
> usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT
> ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
> ada0: <TS128GMTS400 N0815B> ACS-2 ATA SATA 3.x device
> ada0: Serial Number B862500493
> ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 1024bytes)
> ada0: Command Queueing enabled
> ada0: 122104MB (250069680 512 byte sectors)
> SMP: AP CPU #1 Launched!
> Timecounter "TSC" frequency 1396796212 Hz quality 1000
> WARNING: WITNESS option enabled, expect reduced performance.
> Trying to mount root from ufs:/dev/ada0p2 [rw,noatime]...
> usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT
> usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT
> usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT
> ugen0.3: <Unknown> at usbus0 (disconnected)
> uhub_reattach_port: could not allocate new device
> ugen0.3: <Generic> at usbus0
> umass0: <Generic Mass Storage, class 0/0, rev 2.00/1.06, addr 3> on usbus0
> umass0:  SCSI over Bulk-Only; quirks = 0x4101
> umass0:1:0: Attached to scbus1
> da0 at umass-sim0 bus 0 scbus1 target 0 lun 0
> da0: <Generic Flash Disk 8.07> Removable Direct Access SPC-2 SCSI device
> da0: Serial Number F82AEC82
> da0: 40.000MB/s transfers
> da0: 960MB (1966080 512 byte sectors)
> da0: quirks=0x2<NO_6_BYTE>
> GEOM_ELI: Device da0.eli created.
> GEOM_ELI: Encryption: AES-XTS 128
> GEOM_ELI:     Crypto: software
>
> --
> Matthias Apitz, ✉ guru_at_unixarea.de, 🌐 http://www.unixarea.de/  ☎ +49-176-38902045
> _______________________________________________
> freebsd-current_at_freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"