Re: ZFS: can't read MOS of zpool...

From: Alexandre C. Guimarães <rigoletto_at_FreeBSD.org>
Date: Tue, 9 Apr 2019 16:02:31 -0300
Hello,

I don't get those messages when booting from the installation media, all
disks are apparently showing up correctly from `gpart list` from there, and
I updated the bootblocks:

---
# gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 1 ada0
---

however the error messages still do persist on the installed system.

Do I forgot and am not aware of anything?

Thank you.


On Tue, Apr 09, 2019 at 08:43:38PM +0300, Toomas Soome wrote:
> 
> When did you update the bootblocks last time?
> 
> You can grab iso/usb image with current and check if loader there can see your pools - and if yes, update the boot blocks on disk…
> 
> rgds,
> toomas
> 
> > On 9 Apr 2019, at 20:37, Alexandre C. Guimarães <rigoletto_at_FreeBSD.org> wrote:
> > 
> > Hello,
> > 
> > I can't say the precise point this started but I am convinced that was
> > right after running `zpool upgrade` after upgrading to 12-RELEASE:
> > 
> > ---
> > ZFS: i/o error - all block copies unavailable
> > ZFS: can't read MOS of pool zdata
> > ---
> > 
> > So, I got another disk to substitute that one, and now I have the same
> > message two times. :-(
> > 
> > https://ibb.co/G0sfv3p
> > 
> > I suppose that would be very unfortunate to have the same problem in two
> > completely unrelated disks at the same time; however, that error don't
> > occurs with the SSD.
> > 
> > Both disks pools were created raw, however I've tried to do using GPT, MBR,
> > and I got the same error messages.
> > 
> > ---
> > ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
> > ada0: <SanDisk SSD PLUS 120GB UE4500RL> ACS-2 ATA SATA 3.x device
> > ada0: Serial Number 1838DB806764
> > ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 512bytes)
> > ada0: Command Queueing enabled
> > ada0: 114480MB (234455040 512 byte sectors)
> > ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
> > ada1: <SAMSUNG HM320II 2AC101C4> ATA8-ACS SATA 2.x device
> > ada1: Serial Number S22KJ56S906708
> > ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> > ada1: Command Queueing enabled
> > ada1: 305245MB (625142448 512 byte sectors)
> > ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
> > ada2: <APPLE HDD HTS545050A7E362 GG2AB990> ATA8-ACS SATA 2.x device
> > ada2: Serial Number TNS519GY1G75LG
> > ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> > ada2: Command Queueing enabled
> > ada2: 476940MB (976773168 512 byte sectors)
> > ---
> > 
> > What more information would be useful? :-)
> > 
> > Thank you! :-)
> > 
> > -- 
> > Best Regards,
> > Alexandre C. Guimarães.
> > https://bitbucket.org/rigoletto-freebsd/
> 
> _______________________________________________
> freebsd-current_at_freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"

-- 
Best Regards,
Alexandre C. Guimarães.
https://bitbucket.org/rigoletto-freebsd/

Received on Tue Apr 09 2019 - 17:02:33 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:41:20 UTC