Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-BETA3 #1: Wed Aug 26 17:33:09 CEST 2009
    root@phenom.molkerei-ammerland.de:/usr/obj/usr/src/sys/OPTERON
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80df5000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2508379976 Hz
CPU: AMD Phenom(tm) II X4 905e Processor (2508.38-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x100f42  Stepping = 2
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x802009<SSE3,MON,CX16,POPCNT>
  AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x37ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT>
  TSC: P-state invariant
L1 2MB data TLB: 48 entries, fully associative
L1 2MB instruction TLB: 16 entries, fully associative
L1 4KB data TLB: 48 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB data TLB: 128 entries, 2-way associative
L2 2MB instruction TLB: 0 entries, 2-way associative
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
real memory  = 4294967296 (4096 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009afff, 630784 bytes (154 pages)
0x0000000000e1f000 - 0x00000000c7817fff, 3332345856 bytes (813561 pages)
0x0000000100000000 - 0x000000011ffeffff, 536805376 bytes (131056 pages)
avail memory = 3847962624 (3669 MB)
ACPI APIC Table: <080409 APIC2016>
INTR: Adding local APIC 1 as a target
INTR: Adding local APIC 2 as a target
INTR: Adding local APIC 3 as a target
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
APIC: CPU 2 has ACPI ID 3
APIC: CPU 3 has ACPI ID 4
ULE: setup cpu 0
ULE: setup cpu 1
ULE: setup cpu 2
ULE: setup cpu 3
ACPI: RSDP 0xfb4f0 00024 (v2 ACPIAM)
ACPI: XSDT 0xcff90100 0005C (v1 NEC             20090804 MSFT 00000097)
ACPI: FACP 0xcff90290 000F4 (v3 080409 FACP2016 20090804 MSFT 00000097)
ACPI Warning: Optional field Pm2ControlBlock has zero address or length:        0       0/1 20090521 tbfadt-655
ACPI: DSDT 0xcff905d0 0D0D9 (v1  A1391 A1391001 00000001 INTL 20060113)
ACPI: FACS 0xcffa8000 00040
ACPI: APIC 0xcff90390 0007C (v1 080409 APIC2016 20090804 MSFT 00000097)
ACPI: MCFG 0xcff90410 0003C (v1 080409 OEMMCFG  20090804 MSFT 00000097)
ACPI: SLIC 0xcff90450 00176 (v1 NEC             20090804 MSFT 00000097)
ACPI: OEMB 0xcffa8040 00072 (v1 080409 OEMB2016 20090804 MSFT 00000097)
ACPI: HPET 0xcff9f5d0 00038 (v1 080409 OEMHPET  20090804 MSFT 00000097)
ACPI: SSDT 0xcff9f610 0088C (v1 A M I  POWERNOW 00000001 AMD  00000001)
MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
ioapic0 <Version 2.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010400
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
acpi0: <NEC > on motherboard
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xffffff800000e000 pa 0x4000
AcpiOsDerivePciId: \\_SB_.PCI0.RS78.NB2_ -> bus 0 dev 0 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.SATA.SACS -> bus 0 dev 17 func 0
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fec10000, 20 (3) failed
acpi0: reservation of fed40000, 5000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cff00000 (3) failed
ACPI HPET table warning: Sequence is non-zero (2)
ACPI timer: 1/2 1/1 1/2 1/2 1/2 1/2 1/1 1/2 1/2 1/2 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  4 7 10 11 12 14 15
  Validation          0   11   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  4 7 10 11 12 14 15
  Validation          0   10   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  4 7 10 11 12 14 15
  Validation          0   11   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  4 7 10 11 12 14 15
  Validation          0   10   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  4 7 10 11 12 14 15
  Validation          0  255   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  4 7 10 11 12 14 15
  Validation          0  255   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  4 7 10 11 12 14 15
  Validation          0   10   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  4 7 10 11 12 14 15
  Validation          0  255   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route
acpi_hpet0: HPET never increments, disabling
device_attach: acpi_hpet0 attach returned 6
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x1022, dev=0x9601, revid=0x00
	domain=0, bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1043, dev=0x9602, revid=0x00
	domain=0, bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x1a (6500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x9607, revid=0x00
	domain=0, bus=0, slot=7, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.7.INTA
pcib0: slot 7 INTA hardwired to IRQ 19
found->	vendor=0x1022, dev=0x9609, revid=0x00
	domain=0, bus=0, slot=10, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.10.INTA
pcib0: slot 10 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x4391, revid=0x00
	domain=0, bus=0, slot=17, func=0
	class=01-06-01, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0230, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	map[10]: type I/O Port, range 32, base 0xc000, size  3, enabled
	map[14]: type I/O Port, range 32, base 0xb000, size  2, enabled
	map[18]: type I/O Port, range 32, base 0xa000, size  3, enabled
	map[1c]: type I/O Port, range 32, base 0x9000, size  2, enabled
	map[20]: type I/O Port, range 32, base 0x8000, size  4, enabled
	map[24]: type Memory, range 32, base 0xfe7ffc00, size 10, enabled
pcib0: matched entry for 0.17.INTA
pcib0: slot 17 INTA hardwired to IRQ 22
found->	vendor=0x1002, dev=0x4397, revid=0x00
	domain=0, bus=0, slot=18, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0102, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[10]: type Memory, range 32, base 0xfe7fe000, size 12, enabled
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4398, revid=0x00
	domain=0, bus=0, slot=18, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[10]: type Memory, range 32, base 0xfe7fd000, size 12, enabled
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4396, revid=0x00
	domain=0, bus=0, slot=18, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xfe7ff800, size  8, enabled
pcib0: matched entry for 0.18.INTB
pcib0: slot 18 INTB hardwired to IRQ 17
found->	vendor=0x1002, dev=0x4397, revid=0x00
	domain=0, bus=0, slot=19, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0102, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[10]: type Memory, range 32, base 0xfe7fc000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x4398, revid=0x00
	domain=0, bus=0, slot=19, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[10]: type Memory, range 32, base 0xfe7fb000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x4396, revid=0x00
	domain=0, bus=0, slot=19, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xfe7ff400, size  8, enabled
pcib0: matched entry for 0.19.INTB
pcib0: slot 19 INTB hardwired to IRQ 19
found->	vendor=0x1002, dev=0x4385, revid=0x3c
	domain=0, bus=0, slot=20, func=0
	class=0c-05-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x439c, revid=0x00
	domain=0, bus=0, slot=20, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	MSI supports 1 message
	map[20]: type I/O Port, range 32, base 0xff00, size  4, enabled
found->	vendor=0x1002, dev=0x4383, revid=0x00
	domain=0, bus=0, slot=20, func=2
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type Memory, range 64, base 0xfe7f4000, size 14, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x439d, revid=0x00
	domain=0, bus=0, slot=20, func=3
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x4384, revid=0x00
	domain=0, bus=0, slot=20, func=4
	class=06-04-01, hdrtype=0x01, mfdev=1
	cmdreg=0x0105, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x4399, revid=0x00
	domain=0, bus=0, slot=20, func=5
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0102, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=11
	map[10]: type Memory, range 32, base 0xfe7fa000, size 12, enabled
pcib0: matched entry for 0.20.INTC
pcib0: slot 20 INTC hardwired to IRQ 18
found->	vendor=0x1022, dev=0x1200, revid=0x00
	domain=0, bus=0, slot=24, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1201, revid=0x00
	domain=0, bus=0, slot=24, func=1
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1202, revid=0x00
	domain=0, bus=0, slot=24, func=2
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1203, revid=0x00
	domain=0, bus=0, slot=24, func=3
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1204, revid=0x00
	domain=0, bus=0, slot=24, func=4
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xd000-0xdfff
pcib1:   memory decode     0xfe800000-0xfe9fffff
pcib1:   prefetched decode 0xd0000000-0xdfffffff
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found->	vendor=0x1002, dev=0x9710, revid=0x00
	domain=0, bus=1, slot=5, func=0
	class=03-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Prefetchable Memory, range 32, base 0xd0000000, size 28, enabled
pcib1: requested memory range 0xd0000000-0xdfffffff: good
	map[14]: type I/O Port, range 32, base 0xd000, size  8, enabled
pcib1: requested I/O range 0xd000-0xd0ff: in range
	map[18]: type Memory, range 32, base 0xfe9f0000, size 16, enabled
pcib1: requested memory range 0xfe9f0000-0xfe9fffff: good
	map[24]: type Memory, range 32, base 0xfe800000, size 20, enabled
pcib1: requested memory range 0xfe800000-0xfe8fffff: good
pcib1: matched entry for 1.5.INTA
pcib1: slot 5 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x970f, revid=0x00
	domain=0, bus=1, slot=5, func=1
	class=04-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 32, base 0xfe9e8000, size 14, enabled
pcib1: requested memory range 0xfe9e8000-0xfe9ebfff: good
pcib1: matched entry for 1.5.INTB
pcib1: slot 5 INTB hardwired to IRQ 19
vgapci0: <VGA-compatible display> port 0xd000-0xd0ff mem 0xd0000000-0xdfffffff,0xfe9f0000-0xfe9fffff,0xfe800000-0xfe8fffff irq 18 at device 5.0 on pci1
pci1: <multimedia, HDA> at device 5.1 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 19 at device 7.0 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0x0-0x0
pcib2:   memory decode     0xfea00000-0xfeafffff
pcib2:   no prefetched decode
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
found->	vendor=0x197b, dev=0x2380, revid=0x00
	domain=0, bus=2, slot=0, func=0
	class=0c-00-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	map[10]: type Memory, range 32, base 0xfeaff800, size 11, enabled
pcib2: requested memory range 0xfeaff800-0xfeafffff: good
	map[14]: type Memory, range 32, base 0xfeaff400, size  7, enabled
pcib2: requested memory range 0xfeaff400-0xfeaff47f: good
	map[20]: type Memory, range 32, base 0xfeaff000, size  7, enabled
pcib2: requested memory range 0xfeaff000-0xfeaff07f: good
	map[24]: type Memory, range 32, base 0xfeafec00, size  7, enabled
pcib2: requested memory range 0xfeafec00-0xfeafec7f: good
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 19
pci2: <serial bus, FireWire> at device 0.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
pcib3:   domain            0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0xe000-0xefff
pcib3:   memory decode     0xfeb00000-0xfebfffff
pcib3:   prefetched decode 0xfdf00000-0xfdffffff
pci3: <ACPI PCI bus> on pcib3
pci3: domain=0, physical bus=3
found->	vendor=0x10ec, dev=0x8168, revid=0x03
	domain=0, bus=3, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	MSI-X supports 4 messages in map 0x20
	map[10]: type I/O Port, range 32, base 0xe800, size  8, enabled
pcib3: requested I/O range 0xe800-0xe8ff: in range
	map[18]: type Prefetchable Memory, range 64, base 0xfdfff000, size 12, enabled
pcib3: requested memory range 0xfdfff000-0xfdffffff: good
	map[20]: type Prefetchable Memory, range 64, base 0xfdff8000, size 14, enabled
pcib3: requested memory range 0xfdff8000-0xfdffbfff: good
pcib3: matched entry for 3.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 18
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfdfff000-0xfdffffff,0xfdff8000-0xfdffbfff irq 18 at device 0.0 on pci3
re0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xfdfff000
re0: MSI count : 1
re0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 49
re0: using IRQ 256 for MSI
re0: Using 1 MSI messages
re0: Chip rev. 0x28000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: bpf attached
re0: Ethernet address: 00:26:18:86:50:94
re0: [MPSAFE]
re0: [FILTER]
atapci0: <ATI IXP700/800 SATA300 controller> port 0xc000-0xc007,0xb000-0xb003,0xa000-0xa007,0x9000-0x9003,0x8000-0x800f mem 0xfe7ffc00-0xfe7fffff irq 22 at device 17.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8000
atapci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xfe7ffc00
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 0 vector 50
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: AHCI v1.10 controller with 6 3Gbps ports, PM supported
atapci0: Caps: 64bit NCQ SNTF MPS ALP AL CLO 3Gbps PM PMD SSC PSC 32cmd CCC 6ports
ata2: <ATA channel 0> on atapci0
ata2: AHCI reset...
ata2: hardware reset ...
ata2: SATA connect time=0ms status=00000123
ata2: ready wait time=27ms
ata2: software reset port 15...
ata2: ready wait time=0ms
ata2: SIGNATURE: 00000101
ata2: AHCI reset done: devices=00000001
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: AHCI reset...
ata3: hardware reset ...
ata3: SATA connect timeout status=00000000
ata3: AHCI reset done: phy reset found no device
ata3: [MPSAFE]
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: AHCI reset...
ata4: hardware reset ...
ata4: SATA connect time=0ms status=00000123
ata4: ready wait time=27ms
ata4: software reset port 15...
ata4: ready wait time=0ms
ata4: SIGNATURE: 00000101
ata4: AHCI reset done: devices=00000001
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: AHCI reset...
ata5: hardware reset ...
ata5: SATA connect timeout status=00000000
ata5: AHCI reset done: phy reset found no device
ata5: [MPSAFE]
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci0
ata6: AHCI reset...
ata6: hardware reset ...
ata6: SATA connect timeout status=00000000
ata6: AHCI reset done: phy reset found no device
ata6: [MPSAFE]
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci0
ata7: AHCI reset...
ata7: hardware reset ...
ata7: SATA connect timeout status=00000000
ata7: AHCI reset done: phy reset found no device
ata7: [MPSAFE]
ata7: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfe7fe000-0xfe7fefff irq 16 at device 18.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fe000
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 51
ohci0: [MPSAFE]
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xfe7fd000-0xfe7fdfff irq 16 at device 18.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fd000
ohci1: [MPSAFE]
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe7ff800-0xfe7ff8ff irq 17 at device 18.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfe7ff800
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 52
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci2: <OHCI (generic) USB controller> mem 0xfe7fc000-0xfe7fcfff irq 18 at device 19.0 on pci0
ohci2: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fc000
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 53
ohci2: [MPSAFE]
ohci2: [ITHREAD]
usbus3: <OHCI (generic) USB controller> on ohci2
ohci3: <OHCI (generic) USB controller> mem 0xfe7fb000-0xfe7fbfff irq 18 at device 19.1 on pci0
ohci3: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fb000
ohci3: [MPSAFE]
ohci3: [ITHREAD]
usbus4: <OHCI (generic) USB controller> on ohci3
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe7ff400-0xfe7ff4ff irq 19 at device 19.2 on pci0
ehci1: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfe7ff400
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 54
ehci1: [MPSAFE]
ehci1: [ITHREAD]
usbus5: EHCI version 1.0
usbus5: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700/800 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00
ata0: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=00 stat1=00 devices=0x10000
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 55
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 56
ata1: [MPSAFE]
ata1: [ITHREAD]
pci0: <multimedia, HDA> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pcib4:   domain            0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xf000-0xfff
pcib4:   no prefetched decode
pcib4:   Subtractively decoded bridge.
pci4: <ACPI PCI bus> on pcib4
pci4: domain=0, physical bus=4
ohci4: <OHCI (generic) USB controller> mem 0xfe7fa000-0xfe7fafff irq 18 at device 20.5 on pci0
ohci4: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fa000
ohci4: [MPSAFE]
ohci4: [ITHREAD]
usbus6: <OHCI (generic) USB controller> on ohci4
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 57
ppc0: [MPSAFE]
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
plip0: [MPSAFE]
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [MPSAFE]
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 58
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 59
uart0: [FILTER]
uart0: fast interrupt
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x810
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route
Timecounter "HPET" frequency 14318180 Hz quality 900
ahc_isa_probe 0: ioport 0xc00 alloc failed
ex_isa_identify()
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
isa_probe_children: probing non-PnP devices
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 242356 -> 100000
procfs registered
lapic: Divisor 2, Frequency 100335205 hz
Timecounter "TSC" frequency 2508379976 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00010000
ata0: New devices: 00010000
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
usbus6: 12Mbps Full Speed USB v1.0
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
acd0: setting PIO4 on IXP700/800 chip
acd0: setting UDMA66 on IXP700/800 chip
acd0: <HL-DT-STDVD-RAM GH22NP20/1.02> DVDR drive at ata0 as master
acd0: read 8269KB/s (8269KB/s) write 8269KB/s (8269KB/s), 2048KB buffer, UDMA66
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 476940MB <Seagate ST3500630NS 3.AEK> at ata2-master SATA300
ad4: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ugen0.1: <ATI> at usbus0
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
ugen6.1: <ATI> at usbus6
uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
GEOM: new disk ad4
ad4: Silicon Image check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: DDF pri_lba= 976768394 length= 939 blocks
ad4: FAILURE - oversized DMA transfer attempt 480768 > 258048
ad4: setting up DMA failed
ad4: DDF read full metadata failed
ad4: FreeBSD check1 failed
ata3: Identifying devices: 00000000
ata3: New devices: 00000000
ata4: Identifying devices: 00000001
ata4: New devices: 00000001
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad8: 476940MB <Seagate ST3500630NS 3.AEK> at ata4-master SATA300
ad8: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: ad4s1: geometry does not match label (255h,63s != 16h,63s).
ad8: Silicon Image check1 failed
ad8: Adaptec check1 failed
ad8: LSI (v3) check1 failed
ad8: LSI (v2) check1 failed
ad8: DDF pri_lba= 976768394 length= 939 blocks
ad8: FAILURE - oversized DMA transfer attempt 480768 > 258048
ad8: setting up DMA failed
ad8: DDF read full metadata failed
ad8: FreeBSD check1 failed
ata5: Identifying devices: 00000000
ata5: New devices: 00000000
ata6: Identifying devices: 00000000
ata6: New devices: 00000000
ata7: Identifying devices: 00000000
ata7: New devices: 00000000
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
SMP: AP CPU #2 Launched!
cpu2 AP:
     ID: 0x02000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
SMP: AP CPU #3 Launched!
cpu3 AP:
     ID: 0x03000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 1 vector 48
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 2 vector 48
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 3 vector 48
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 1 vector 49
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 2 vector 49
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 3 vector 49
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 1 vector 50
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 2 vector 50
msi: Assigning MSI IRQ 256 to local APIC 3 vector 50
GEOM: new disk ad8
GEOM: ad8s1: geometry does not match label (255h,63s != 16h,63s).
Root mount waiting for: usbus6 usbus5 usbus4 usbus3 usbus2 usbus1 usbus0
uhub6: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub4: 3 ports with 3 removable, self powered
Root mount waiting for: usbus5 usbus2
Root mount waiting for: usbus5 usbus2
uhub2: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
ugen5.2: <Generic> at usbus5
umass0: <Bulk-In, Bulk-Out, Interface> on usbus5
umass0:  SCSI over Bulk-Only; quirks = 0x0000
Root mount waiting for: usbus5
umass0:0:0:-1: Attached to scbus0
Trying to mount root from ufs:/dev/ad4s1a
(probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?
ct_to_ts([2009-08-26 15:42:32]) = 1251301352.000000000
start_init: trying /sbin/init
(probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:0): Medium not present
(probe0:umass-sim0:0:0:0): (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim0:0:0:0): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:0): Medium not present
Unretryable error
(probe0:umass-sim0:0:0:0): error 6
(probe0:umass-sim0:0:0:0): Unretryable Error
pass0 at umass-sim0 bus 0 target 0 lun 0
pass0: <Generic- Compact Flash 1.00> Removable Direct Access SCSI-0 device 
pass0: 40.000MB/s transfers
GEOM: new disk da0
(da0:umass-sim0:0:0:0): error 6
(da0:umass-sim0:0:0:0): Unretryable Error
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Generic- Compact Flash 1.00> Removable Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): error 6
(da0:umass-sim0:0:0:0): Unretryable Error
Opened disk da0 -> 6
(probe0:umass-sim0:0:0:1): Down reving Protocol Version from 2 to 0?
(da0:umass-sim0:0:0:0): error 6
(da0:umass-sim0:0:0:0): Unretryable Error
Opened disk da0 -> 6
(probe0:umass-sim0:0:0:1): TEST UNIT READY. CDB: 0 20 0 0 0 0 
(probe0:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:1): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:1): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:1): Medium not present
(probe0:umass-sim0:0:0:1): (probe0:umass-sim0:0:0:1): TEST UNIT READY. CDB: 0 20 0 0 0 0 
(probe0:umass-sim0:0:0:1): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:1): Medium not present
Unretryable error
(probe0:umass-sim0:0:0:1): error 6
(probe0:umass-sim0:0:0:1): Unretryable Error
pass1 at umass-sim0 bus 0 target 0 lun 1
pass1: <Generic- SM/xD-Picture 1.00> Removable Direct Access SCSI-0 device 
pass1: 40.000MB/s transfers
(da1:umass-sim0:0:0:1): error 6
(da1:umass-sim0:0:0:1): Unretryable Error
da1 at umass-sim0 bus 0 target 0 lun 1
da1: <Generic- SM/xD-Picture 1.00> Removable Direct Access SCSI-0 device 
da1: 40.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
(probe0:umass-sim0:0:0:2): Down reving Protocol Version from 2 to 0?
GEOM: new disk da1
(probe0:umass-sim0:0:0:2): TEST UNIT READY. CDB: 0 40 0 0 0 0 
(probe0:umass-sim0:0:0:2): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:2): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:2): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:2): Medium not present
(probe0:umass-sim0:0:0:2): (probe0:umass-sim0:0:0:2): TEST UNIT READY. CDB: 0 40 0 0 0 0 
(probe0:umass-sim0:0:0:2): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:2): Medium not present
Unretryable error
(probe0:umass-sim0:0:0:2): error 6
(probe0:umass-sim0:0:0:2): Unretryable Error
pass2 at umass-sim0 bus 0 target 0 lun 2
pass2: <Generic- SD/MMC 1.00> Removable Direct Access SCSI-0 device 
pass2: 40.000MB/s transfers
(da1:umass-sim0:0:0:1): error 6
(da1:umass-sim0:0:0:1): Unretryable Error
Opened disk da1 -> 6
(da2:umass-sim0:0:0:2): error 6
(da2:umass-sim0:0:0:2): Unretryable Error
da2 at umass-sim0 bus 0 target 0 lun 2
da2: <Generic- SD/MMC 1.00> Removable Direct Access SCSI-0 device 
da2: 40.000MB/s transfers
da2: Attempt to query device size failed: NOT READY, Medium not present
(da1:umass-sim0:0:0:1): error 6
(da1:umass-sim0:0:0:1): Unretryable Error
Opened disk da1 -> 6
GEOM: new disk da2
(da2:umass-sim0:0:0:2): error 6
(da2:umass-sim0:0:0:2): Unretryable Error
Opened disk da2 -> 6
(probe0:umass-sim0:0:0:3): Down reving Protocol Version from 2 to 0?
(da2:umass-sim0:0:0:2): error 6
(da2:umass-sim0:0:0:2): Unretryable Error
Opened disk da2 -> 6
(probe0:umass-sim0:0:0:3): TEST UNIT READY. CDB: 0 60 0 0 0 0 
(probe0:umass-sim0:0:0:3): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:3): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:3): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:3): Medium not present
(probe0:umass-sim0:0:0:3): (probe0:umass-sim0:0:0:3): TEST UNIT READY. CDB: 0 60 0 0 0 0 
(probe0:umass-sim0:0:0:3): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:3): Medium not present
Unretryable error
(probe0:umass-sim0:0:0:3): error 6
(probe0:umass-sim0:0:0:3): Unretryable Error
pass3 at umass-sim0 bus 0 target 0 lun 3
pass3: <Generic- MS/MS-Pro 1.00> Removable Direct Access SCSI-0 device 
pass3: 40.000MB/s transfers
GEOM: new disk da3
(da3:umass-sim0:0:0:3): error 6
(da3:umass-sim0:0:0:3): Unretryable Error
da3 at umass-sim0 bus 0 target 0 lun 3
da3: <Generic- MS/MS-Pro 1.00> Removable Direct Access SCSI-0 device 
da3: 40.000MB/s transfers
da3: Attempt to query device size failed: NOT READY, Medium not present
(da3:umass-sim0:0:0:3): error 6
(da3:umass-sim0:0:0:3): Unretryable Error
Opened disk da3 -> 6
(da3:umass-sim0:0:0:3): error 6
(da3:umass-sim0:0:0:3): Unretryable Error
Opened disk da3 -> 6
splash: image decoder found: green_saver
re0: link state changed to UP
re0: link state changed to DOWN
re0: link state changed to UP
re0: link state changed to DOWN
re0: link state changed to UP
pci0: driver added
found->	vendor=0x1002, dev=0x4385, revid=0x3c
	domain=0, bus=0, slot=20, func=0
	class=0c-05-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:20:0: reprobing on driver added
found->	vendor=0x1002, dev=0x4383, revid=0x00
	domain=0, bus=0, slot=20, func=2
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 2  supports D0 D3  current D0
pci0:0:20:2: reprobing on driver added
pci1: driver added
found->	vendor=0x1002, dev=0x970f, revid=0x00
	domain=0, bus=1, slot=5, func=1
	class=04-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
pci0:1:5:1: reprobing on driver added
pci2: driver added
found->	vendor=0x197b, dev=0x2380, revid=0x00
	domain=0, bus=2, slot=0, func=0
	class=0c-00-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=19
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
pci0:2:0:0: reprobing on driver added
fwohci0: vendor=197b, dev=2380
fwohci0: vendor=197b, dev=2380
fwohci0: <1394 Open Host Controller Interface> mem 0xfeaff800-0xfeafffff,0xfeaff400-0xfeaff47f,0xfeaff000-0xfeaff07f,0xfeafec00-0xfeafec7f irq 19 at device 0.0 on pci2
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xfeaff800
fwohci0: [MPSAFE]
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:1e:8c:00:01:fa:e5:d9
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata:: 0x5 loop=100, retry=100
fwohci0: fwphy_rddata:: 0x2 loop=100, retry=100
fwohci0: Link S400, max_rec 2048 bytes.
pci3: driver added
pci4: driver added
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata:: 0x1 loop=100, retry=100
fwohci0: fwphy_rddata:: 0x1 loop=100, retry=100
sbp0: <SBP-2/SCSI over FireWire> on firewire0