I'm running: FreeBSD 5.1-CURRENT #18: Sat Aug 9 16:53:59 EDT 2003 marcus_at_gyros.marcuscom.com:/usr/obj/usr/src/sys/GYROS And I just bought one of those 256 MB USB JumpDrives. The drive works fine under -STABLE and in USB 1.1 slots on -CURRENT: umass0: LEXAR MEDIA JUMPDRIVE PRO, rev 2.00/0.00, addr 2 da0 at umass-sim0 bus 0 target 0 lun 0 da0: <LEXAR JUMPDRIVE PRO 0> Removable Direct Access SCSI-2 device da0: 1.000MB/s transfers da0: 246MB (503808 512 byte sectors: 64H 32S/T 246C) However, if I have ehci compiled into my kernel (needed to get usbd to detect new devices), I see the following when I plug the drive in: usb3: unrecoverable error, controller halted usb3: blocking intrs 0x10 USB does work on this machine (as long as the device is a USB 1.x device). I have tested a USB mouse, a Sony camera, and a USB serial adapter. All work as expected. I have an Intel-based USB controller in this laptop: ehci0_at_pci0:29:7: class=0x0c0320 card=0x015f1028 chip=0x24cd8086 rev=0x03 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB (ICH4) USB EHCI Controller' class = serial bus subclass = USB But, of course, it's detected as a generic EHCI controller: ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd0000000-0xd00003ff irq 10 at device 29.7 on pci0 ehci_pci_attach: companion usb0 ehci_pci_attach: companion usb1 ehci_pci_attach: companion usb2 usb3: EHCI version 1.0 usb3: companion controllers, 2 ports each: usb0 usb1 usb2 usb3: <EHCI (generic) USB 2.0 controller> on ehci0 usb3: USB revision 2.0 uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub3: 6 ports with 6 removable, self powered I haven't tried applying the patch to get it detected as an actual Intel controller, but I'm not sure that would help. Any ideas? Full dmesg follows. Thanks. Joe Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-CURRENT #18: Sat Aug 9 16:53:59 EDT 2003 marcus_at_gyros.marcuscom.com:/usr/obj/usr/src/sys/GYROS Preloaded elf kernel "/boot/kernel/kernel" at 0xc0510000. Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc05102c8. Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0510374. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0510420. Timecounter "i8254" frequency 1193182 Hz CPU: Genuine Intel(R) CPU 3.06GHz (3056.50-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 1072562176 (1022 MB) avail memory = 1036513280 (988 MB) Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL MwoodNwd> on motherboard pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00fdf30 ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc61375a0), AE_NOT_EXIST acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc61375a0), AE_NOT_EXIST acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib0: slot 29 INTA is routed to irq 10 pcib0: slot 29 INTB is routed to irq 11 pcib0: slot 29 INTC is routed to irq 11 pcib0: slot 29 INTD is routed to irq 10 pcib0: slot 31 INTB is routed to irq 10 pcib0: slot 31 INTB is routed to irq 10 pcib0: slot 31 INTB is routed to irq 10 agp0: <Intel Generic host to PCI bridge> mem 0xe0000000-0xefffffff at device 0.0 on pci0 pci0: <base peripheral> at device 0.1 (no driver attached) pci0: <base peripheral> at device 0.3 (no driver attached) pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib1: slot 0 INTA is routed to irq 5 pci1: <display, VGA> at device 0.0 (no driver attached) uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 10 at device 29.0 on pci0 usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ums0: Microsoft Microsoft IntelliMouse® Explorer, rev 1.10/1.14, addr 2, iclass 3/1 ums0: 5 buttons and Z dir. uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 11 at device 29.1 on pci0 usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 11 at device 29.2 on pci0 usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd0000000-0xd00003ff irq 10 at device 29.7 on pci0 ehci_pci_attach: companion usb0 ehci_pci_attach: companion usb1 ehci_pci_attach: companion usb2 usb3: EHCI version 1.0 usb3: companion controllers, 2 ports each: usb0 usb1 usb2 usb3: <EHCI (generic) USB 2.0 controller> on ehci0 usb3: USB revision 2.0 uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub3: 6 ports with 6 removable, self powered pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pcib2: slot 1 INTA is routed to irq 10 pcib2: slot 4 INTA is routed to irq 10 pcib2: slot 4 INTA is routed to irq 10 pci2: <network, ethernet> at device 1.0 (no driver attached) cbb0: <TI4510 PCI-CardBus Bridge> irq 10 at device 4.0 on pci2 start (88000000) < sc->membase (d0200000) end (ffffffff) > sc->memlimit (d02fffff) cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 fwohci0: vendor=104c, dev=8029 fwohci0: <1394 Open Host Controller Interface> mem 0xd0200000-0xd0203fff,0xd0206000-0xd02067ff irq 10 at device 4.1 on pci2 fwohci0: OHCI version 1.10 (ROM=0) fwohci0: No. of Isochronous channel is 4. fwohci0: EUI64 00:c0:4f:34:0d:90:90:61 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 sbp0: <SBP2/SCSI over firewire> on firewire0 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0x1860-0x186f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pcm0: <Intel ICH4 (82801DB)> port 0x18c0-0x18ff,0x1c00-0x1cff mem 0xd0000800-0xd00008ff,0xd0000c00-0xd0000dff irq 10 at device 31.5 on pci0 pcm0: <SigmaTel STAC9750/51 AC97 Codec> pci0: <simple comms> at device 31.6 (no driver attached) acpi_ec0: <embedded controller: GPE 0x1c> port 0x66,0x62 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 acpi_acad0: <AC adapter> on acpi0 orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xdc000-0xdffff,0xd1000-0xd27ff,0xd0000-0xd0fff,0xc0000-0xcffff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 3056502372 Hz Timecounters tick every 10.000 msec acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% system power profile changed to 'economy' ad2: 57231MB <HITACHI_DK23FB-60> [116280/16/63] at ata1-master UDMA100 acd0: CD-RW <QSI CD-RW/DVD-ROM SBW-242> at ata0-master UDMA33 ums0: at uhub0 port 1 (addr 2) disconnected ums0: detached ums0: Microsoft Microsoft IntelliMouse® Explorer, rev 1.10/1.14, addr 2, iclass 3/1 ums0: 5 buttons and Z dir. Mounting root from ufs:/dev/ad2s3a cd0 at ata0 bus 0 target 0 lun 0 cd0: <QSI CDRW/DVD SBW-242 UD22> Removable CD-ROM SCSI-0 device cd0: 33.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present system power profile changed to 'performance' bcm0: <Broadcom 10/100 Base-T Ethernet> mem 0xd0204000-0xd0205fff irq 10 at device 1.0 on pci2 bcm0: Ethernet address: 00:0b:db:9c:4a:bd miibus0: <MII bus> on bcm0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto drm0: <ATI Radeon Lf R250 Mobility 9000 M9> port 0x3000-0x30ff mem 0xd0100000-0xd010ffff,0xd8000000-0xdfffffff irq 5 at device 0.0 on pci1 info: [drm] AGP at 0xe0000000 256MB info: [drm] Initialized radeon 1.8.0 20020828 on minor 0 info: [drm] Loading R200 Microcode stray irq 7 stray irq 7 ums0: at uhub0 port 1 (addr 2) disconnected ums0: detached usb3: unrecoverable error, controller halted usb3: blocking intrs 0x10 uhub3: device problem, disabling port 1 ums0: Microsoft Microsoft IntelliMouse® Explorer, rev 1.10/1.14, addr 2, iclass 3/1 ums0: 5 buttons and Z dir. -- PGP Key : http://www.marcuscom.com/pgp.asc
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:18 UTC