The simple question is does the Atheros driver support the AR5001X adapter ? I am using a Toshiba A35 S159 Laptop with the built in AR5001X adapter that supports both 802.11 B and G with the Generic kernel. I haven't built a custom kernel since i noticed that there were if_ath.ko and ath_hal.ko modules in the kernel directory. I've tried the following after booting: kldload ath_hal which reports no errors kldload if_ath which reports the following errors: ath0: <Atheros 5212> mem 0xe0201000-0xe0210fff irq 22 at device 2.0 on Pci2 Pcib1 device ath0 requested decoded memory range 0xe0201000-0xe0210fff atho: unable to attach hardware; HAL status 3 device_probe_and_attach: ath0 attach returned 6 The module loads as reported by kldstat however the interface does not show up. The settings XP is using are: IRQ: 22 Memory Range: E0200000-E020FFFF Location: PCI bus 2, device 2, function 0 The obvious solution at the moment is to modify the driver to use the same memory range that windows uses. Any ideas/suggestions. ----------------dmesg---------- Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-BETA #0: Tue Nov 25 08:24:08 GMT 2003 root_at_wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a76000. ACPI APIC Table: <PTLTD APIC > Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Genuine Intel(R) CPU 2.30GHz (2298.06-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 502136832 (478 MB) avail memory = 478072832 (455 MB) ioapic0 <Version 2.0> irqs 0-23 on motherboard Pentium Pro MTRR support enabled acpi0: <TOSCPL RSDT > on motherboard pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00fdf30 acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_cpu1: Failed to attach throttling P_CNT acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <base peripheral> at device 0.1 (no driver attached) pci0: <base peripheral> at device 0.3 (no driver attached) agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0x1800-0x1807 mem 0xe0000000-0xe007ffff,0xe8000000-0xefffffff irq 16 at device 2.0 on pci0 agp0: detected 32636k stolen memory agp0: aperture size is 128M pci0: <display> at device 2.1 (no driver attached) uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1820-0x183f irq 16 at device 29.0 on pci0 usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1840-0x185f irq 19 at device 29.1 on pci0 usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhub2: Texas Instruments General Purpose USB Hub, class 9/0, rev 1.10/1.01, addr 2 uhub2: 2 ports with 0 removable, bus powered ums0: Logitech USB Receiver, rev 1.10/27.04, addr 3, iclass 3/1 ums0: 7 buttons and Z dir. uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1860-0x187f irq 18 at device 29.2 on pci0 usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib1 rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem 0xe0210000-0xe02100ff irq 21 at device 1.0 on pci2 rl0: Ethernet address: 00:02:3f:93:e5:97 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci2: <network, ethernet> at device 2.0 (no driver attached) cbb0: <ENE CB1410 PCI-CardBus Bridge> at device 4.0 on pci2 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb0: [MPSAFE] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0x1810-0x181f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pci0: <multimedia, audio> at device 31.5 (no driver attached) pci0: <simple comms> at device 31.6 (no driver attached) acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0 acpi_acad0: <AC Adapter> on acpi0 ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc447e340), AE_NO_HARDWARE_RESPONSE acpi_cmbat0: <Control Method Battery> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xdf000-0xdffff,0xcd000-0xcdfff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 2298060352 Hz quality 800 Timecounters tick every 10.000 msec acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% cbb0: Unsupported card type detected GEOM: create disk ad0 dp=0xc45d3860 ad0: 57231MB <HITACHI_DK23EA-60> [116280/16/63] at ata0-master UDMA100 acd0: CDRW <DW-224E-A> at ata1-master PIO4 Mounting root from ufs:/dev/ad0s2a Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-BETA #0: Tue Nov 25 08:24:08 GMT 2003 root_at_wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a76000. ACPI APIC Table: <PTLTD APIC > Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Genuine Intel(R) CPU 2.30GHz (2298.06-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 502136832 (478 MB) avail memory = 478072832 (455 MB) ioapic0 <Version 2.0> irqs 0-23 on motherboard Pentium Pro MTRR support enabled acpi0: <TOSCPL RSDT > on motherboard pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00fdf30 acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_cpu1: Failed to attach throttling P_CNT acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <base peripheral> at device 0.1 (no driver attached) pci0: <base peripheral> at device 0.3 (no driver attached) agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0x1800-0x1807 mem 0xe0000000-0xe007ffff,0xe8000000-0xefffffff irq 16 at device 2.0 on pci0 agp0: detected 32636k stolen memory agp0: aperture size is 128M pci0: <display> at device 2.1 (no driver attached) uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1820-0x183f irq 16 at device 29.0 on pci0 usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1840-0x185f irq 19 at device 29.1 on pci0 usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhub2: Texas Instruments General Purpose USB Hub, class 9/0, rev 1.10/1.01, addr 2 uhub2: 2 ports with 0 removable, bus powered ums0: Logitech USB Receiver, rev 1.10/27.04, addr 3, iclass 3/1 ums0: 7 buttons and Z dir. uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1860-0x187f irq 18 at device 29.2 on pci0 usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib1 rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem 0xe0210000-0xe02100ff irq 21 at device 1.0 on pci2 rl0: Ethernet address: 00:02:3f:93:e5:97 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci2: <network, ethernet> at device 2.0 (no driver attached) cbb0: <ENE CB1410 PCI-CardBus Bridge> at device 4.0 on pci2 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb0: [MPSAFE] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0x1810-0x181f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pci0: <multimedia, audio> at device 31.5 (no driver attached) pci0: <simple comms> at device 31.6 (no driver attached) acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0 acpi_acad0: <AC Adapter> on acpi0 ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc447e340), AE_NO_HARDWARE_RESPONSE acpi_cmbat0: <Control Method Battery> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xdf000-0xdffff,0xcd000-0xcdfff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 2298060352 Hz quality 800 Timecounters tick every 10.000 msec acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% cbb0: Unsupported card type detected GEOM: create disk ad0 dp=0xc45d3860 ad0: 57231MB <HITACHI_DK23EA-60> [116280/16/63] at ata0-master UDMA100 acd0: CDRW <DW-224E-A> at ata1-master PIO4 Mounting root from ufs:/dev/ad0s2aReceived on Sat Dec 06 2003 - 10:04:31 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:32 UTC