Try adding to your /boot/loader.conf hw.pci.allow_unsupported_io_range="1" and reboot. kt On Sat, Dec 06, 2003 at 02:04:29PM -0500, tn wrote: > The simple question is does the Atheros driver support the AR5001X adapter ? > > I am using a Toshiba A35 S159 Laptop with the built in AR5001X adapter > that supports both 802.11 B and G with the Generic kernel. I haven't > built a custom kernel since i noticed that there were if_ath.ko and > ath_hal.ko modules in the kernel directory. > > I've tried the following after booting: > kldload ath_hal which reports no errors > kldload if_ath which reports the following errors: > ath0: <Atheros 5212> mem 0xe0201000-0xe0210fff irq 22 at device 2.0 > on Pci2 > Pcib1 device ath0 requested decoded memory range 0xe0201000-0xe0210fff > atho: unable to attach hardware; HAL status 3 > device_probe_and_attach: ath0 attach returned 6 > > The module loads as reported by kldstat however the interface does not > show up. > > The settings XP is using are: > IRQ: 22 > Memory Range: E0200000-E020FFFF > Location: PCI bus 2, device 2, function 0 > > The obvious solution at the moment is to modify the driver to use the > same memory range that windows uses. > > Any ideas/suggestions. > > ----------------dmesg---------- > > > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.2-BETA #0: Tue Nov 25 08:24:08 GMT 2003 > root_at_wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a76000. > ACPI APIC Table: <PTLTD APIC > > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Genuine Intel(R) CPU 2.30GHz (2298.06-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > real memory = 502136832 (478 MB) > avail memory = 478072832 (455 MB) > ioapic0 <Version 2.0> irqs 0-23 on motherboard > Pentium Pro MTRR support enabled > acpi0: <TOSCPL RSDT > on motherboard > pcibios: BIOS version 2.10 > Using $PIR table, 9 entries at 0xc00fdf30 > acpi0: Power Button (fixed) > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_cpu1: <CPU> on acpi0 > acpi_cpu1: Failed to attach throttling P_CNT > acpi_lid0: <Control Method Lid Switch> on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: <base peripheral> at device 0.1 (no driver attached) > pci0: <base peripheral> at device 0.3 (no driver attached) > agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0x1800-0x1807 mem > 0xe0000000-0xe007ffff,0xe8000000-0xefffffff irq 16 at device 2.0 on pci0 > agp0: detected 32636k stolen memory > agp0: aperture size is 128M > pci0: <display> at device 2.1 (no driver attached) > uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1820-0x183f > irq 16 at device 29.0 on pci0 > usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1840-0x185f > irq 19 at device 29.1 on pci0 > usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhub2: Texas Instruments General Purpose USB Hub, class 9/0, rev > 1.10/1.01, addr 2 > uhub2: 2 ports with 0 removable, bus powered > ums0: Logitech USB Receiver, rev 1.10/27.04, addr 3, iclass 3/1 > ums0: 7 buttons and Z dir. > uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1860-0x187f > irq 18 at device 29.2 on pci0 > usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 > usb2: USB revision 1.0 > uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub3: 2 ports with 2 removable, self powered > pci0: <serial bus, USB> at device 29.7 (no driver attached) > pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib1 > rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem > 0xe0210000-0xe02100ff irq 21 at device 1.0 on pci2 > rl0: Ethernet address: 00:02:3f:93:e5:97 > miibus0: <MII bus> on rl0 > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > pci2: <network, ethernet> at device 2.0 (no driver attached) > cbb0: <ENE CB1410 PCI-CardBus Bridge> at device 4.0 on pci2 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > cbb0: [MPSAFE] > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH4 UDMA100 controller> port > 0x1810-0x181f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata0: [MPSAFE] > ata1: at 0x170 irq 15 on atapci0 > ata1: [MPSAFE] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > pci0: <multimedia, audio> at device 31.5 (no driver attached) > pci0: <simple comms> at device 31.6 (no driver attached) > acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0 > acpi_acad0: <AC Adapter> on acpi0 > ACPI-0438: *** Error: Handler for [EmbeddedControl] returned > AE_NO_HARDWARE_RESPONSE > ACPI-1287: *** Error: Method execution failed > [\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc447e340), AE_NO_HARDWARE_RESPONSE > acpi_cmbat0: <Control Method Battery> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port > 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 > ppc0 port 0x378-0x37f irq 7 on acpi0 > ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > orm0: <Option ROMs> at iomem > 0xe0000-0xe3fff,0xdf000-0xdffff,0xcd000-0xcdfff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 or not responding > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 2298060352 Hz quality 800 > Timecounters tick every 10.000 msec > acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% > cbb0: Unsupported card type detected > GEOM: create disk ad0 dp=0xc45d3860 > ad0: 57231MB <HITACHI_DK23EA-60> [116280/16/63] at ata0-master UDMA100 > acd0: CDRW <DW-224E-A> at ata1-master PIO4 > Mounting root from ufs:/dev/ad0s2a > > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.2-BETA #0: Tue Nov 25 08:24:08 GMT 2003 > root_at_wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a76000. > ACPI APIC Table: <PTLTD APIC > > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Genuine Intel(R) CPU 2.30GHz (2298.06-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > real memory = 502136832 (478 MB) > avail memory = 478072832 (455 MB) > ioapic0 <Version 2.0> irqs 0-23 on motherboard > Pentium Pro MTRR support enabled > acpi0: <TOSCPL RSDT > on motherboard > pcibios: BIOS version 2.10 > Using $PIR table, 9 entries at 0xc00fdf30 > acpi0: Power Button (fixed) > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_cpu1: <CPU> on acpi0 > acpi_cpu1: Failed to attach throttling P_CNT > acpi_lid0: <Control Method Lid Switch> on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: <base peripheral> at device 0.1 (no driver attached) > pci0: <base peripheral> at device 0.3 (no driver attached) > agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0x1800-0x1807 mem 0xe0000000-0xe007ffff,0xe8000000-0xefffffff irq 16 at device 2.0 on pci0 > agp0: detected 32636k stolen memory > agp0: aperture size is 128M > pci0: <display> at device 2.1 (no driver attached) > uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1820-0x183f irq 16 at device 29.0 on pci0 > usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1840-0x185f irq 19 at device 29.1 on pci0 > usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhub2: Texas Instruments General Purpose USB Hub, class 9/0, rev 1.10/1.01, addr 2 > uhub2: 2 ports with 0 removable, bus powered > ums0: Logitech USB Receiver, rev 1.10/27.04, addr 3, iclass 3/1 > ums0: 7 buttons and Z dir. > uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1860-0x187f irq 18 at device 29.2 on pci0 > usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 > usb2: USB revision 1.0 > uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub3: 2 ports with 2 removable, self powered > pci0: <serial bus, USB> at device 29.7 (no driver attached) > pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib1 > rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem 0xe0210000-0xe02100ff irq 21 at device 1.0 on pci2 > rl0: Ethernet address: 00:02:3f:93:e5:97 > miibus0: <MII bus> on rl0 > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > pci2: <network, ethernet> at device 2.0 (no driver attached) > cbb0: <ENE CB1410 PCI-CardBus Bridge> at device 4.0 on pci2 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > cbb0: [MPSAFE] > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH4 UDMA100 controller> port 0x1810-0x181f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata0: [MPSAFE] > ata1: at 0x170 irq 15 on atapci0 > ata1: [MPSAFE] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > pci0: <multimedia, audio> at device 31.5 (no driver attached) > pci0: <simple comms> at device 31.6 (no driver attached) > acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0 > acpi_acad0: <AC Adapter> on acpi0 > ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc447e340), AE_NO_HARDWARE_RESPONSE > acpi_cmbat0: <Control Method Battery> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 > ppc0 port 0x378-0x37f irq 7 on acpi0 > ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xdf000-0xdffff,0xcd000-0xcdfff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 or not responding > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 2298060352 Hz quality 800 > Timecounters tick every 10.000 msec > acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% > cbb0: Unsupported card type detected > GEOM: create disk ad0 dp=0xc45d3860 > ad0: 57231MB <HITACHI_DK23EA-60> [116280/16/63] at ata0-master UDMA100 > acd0: CDRW <DW-224E-A> at ata1-master PIO4 > Mounting root from ufs:/dev/ad0s2a >Received on Sun Dec 07 2003 - 05:02:47 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:32 UTC