I feel your pain, my thinkpad doesn't co-operate with 5.1 either... ajt. On Tue, May 27, 2003 at 11:10:26AM -0400, Mikhail Kruk wrote: > Hello, > I've seen this reported before, but don't see a resolution. Maybe my > logs will help solve the problem. > When my Gateway laptop boots, I get a couple of logs about ACPI problems. > See attached dmesg.txt > Later (10-30 minutes) I get a crash with the following trace. > > Fatal trap 12: page fault while in kernel mode > fault virtual address = 0x80790ab0 > fault code = supervisor read, page not present > instruction pointer = 0x8:0xc06ea4d0 > stack pointer = 0x10:0xcd10bbf0 > frame pointer = 0x19:0xcd10bbf0 > code segment = base 0x0, limit 0xfffff, type 0x1b > = DPL 0, pres 1, def32 1, gran 1 > processor eflags = interrupt enabled, resume, IOPL = 0 > current process = 6 (acpi_task1) > kernel: type 12 trap, code=0 > Stopped at AcpiNsMapHandleToNode+0x20: cmpb $0xaa,0(%edx) > > trace: > AcpiNsMapHandleToNode contrib/dev/acpica/nsutils.c > AcpiGetHandle > acpi_pwer_switch_consumer dev/acpica/acpi_powerres.c > acpi_tz_switch_cooler_on dev/acpica/acpi_thermal.c > acpi_ForeachPackageObject dev/acpica/acpi_thermal.c > acpi_tz_monitor > atcpi_task_thread > fork_exit > fork_trampoline > > The trace is always the same, but the process is different (acpi_task1, > _task2, _thermal) > The problem is easily reproduced by doing a big compilation (kernel or > buildworld). > > See also: > http://polkan2.dyndns.org/~meshko/foo.dsdt > http://polkan2.dyndns.org/~meshko/foo.asl > > I also have a couple of related questions. > 1) I tried putting some debug outputs in acpi code, and messages that I > put in contrib/dev/acpica/* are showing up. However messages I put in > dev/acpica do not seem to go anywhere. I can't find any object files > generated from that directory. What am I missing? > > 2) Is there a workaround for this problem before ACPI gets fixed? I tried > booting without it (unset acpi_enable), but it just hangs during the boot. > Would it work if I disabled some part of ACPI? Would the laptop overheat > if I do that? Can I somehow enable APM instead of ACPI? RedHat 8 works > fine on the same laptop and it seems to be using APM only, no ACPI. > > Please cc: me, not subscribed. > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.1-BETA #0: Fri May 23 12:28:16 GMT 2003 > root_at_begemot.dyndns.org:/usr/src/sys/i386/compile/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc071a000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc071a0a8. > Timecounter "i8254" frequency 1193182 Hz > Timecounter "TSC" frequency 2392954684 Hz > CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2392.95-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 > Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > real memory = 267911168 (255 MB) > avail memory = 252489728 (240 MB) > Pentium Pro MTRR support enabled > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <GATEWA 400 > on motherboard > pcibios: BIOS version 2.10 > Using $PIR table, 11 entries at 0xc00fdf10 > acpi0: power button is handled as a fixed feature programming model. > Timecounter "ACPI-fast" frequency 3579545 Hz > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_tz0: <thermal zone> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <Intel 82845 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0 on pci0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 10 at device 29.0 on pci0 > usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 10 at device 2.0 on pci2 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > pci2: <multimedia, audio> at device 3.0 (no driver attached) > fwohci0: vendor=104c, dev=8026 > fwohci0: <1394 Open Host Controller Interface> mem 0xe8200000-0xe8203fff,0xe8206000-0xe82067ff irq 10 at device 5.0 on pci2 > fwohci0: OHCI version 1.10 (ROM=1) > fwohci0: No. of Isochronous channel is 4. > fwohci0: EUI64 00:e0:b8:04:01:01:ec:f1 > fwohci0: Phy 1394a available S400, 1 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > if_fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:e0:b8:01:ec:f1 > sbp0: <SBP2/SCSI over firewire> on firewire0 > fwohci0: Initiate bus reset > fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x3c00-0x3c3f mem 0xe8205000-0xe8205fff irq 10 at device 8.0 on pci2 > fxp0: Ethernet address 00:e0:b8:50:23:7b > miibus0: <MII bus> on fxp0 > inphy0: <i82562ET 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH3 UDMA100 controller> port 0x1820-0x182f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xe8000000-0xe80003ff at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > pci0: <simple comms> at device 31.6 (no driver attached) > acpi_lid0: <Control Method Lid Switch> on acpi0 > ACPI-1287: *** Error: Method execution failed [\\_SB_.LID_._PSW] (Node 0xc2622e80), AE_NOT_EXIST > acpi_acad0: <AC adapter> on acpi0 > acpi_cmbat0: <Control method Battery> on acpi0 > acpi_button0: <Sleep Button> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 > ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xc0000-0xccfff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 or not responding > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounters tick every 10.000 msec > fwohci0: BUS reset > fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% > cbb0: Unsupported card type detected > ad0: 28615MB <IC25N030ATCS04-0> [58140/16/63] at ata0-master UDMA100 > acd0: CD-RW <QSI CD-RW/DVD-ROM SBW-241> at ata1-master PIO4 > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_TZ_.THRM._TMP] (Node 0xc2622420), AE_ERROR > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > Mounting root from ufs:/dev/ad0s2a > WARNING: / was not properly dismounted > WARNING: /tmp was not properly dismounted > /tmp: superblock summary recomputed > WARNING: /usr was not properly dismounted > /usr: mount pending error: blocks 76 files 31 > /usr: superblock summary recomputed > WARNING: /var was not properly dismounted > interface fwe.1 already present in the KLD 'kernel'! > module_register: module pci/fxp already exists! > Module pci/fxp failed to register: 17 > module_register: module cardbus/fxp already exists! > Module cardbus/fxp failed to register: 17 > module_register: module fxp/miibus already exists! > Module fxp/miibus failed to register: 17 > can't re-use a leaf (fxp_rnr)! > can't re-use a leaf (fxp_noflow)! > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.1-BETA #0: Fri May 23 12:28:16 GMT 2003 > root_at_begemot.dyndns.org:/usr/src/sys/i386/compile/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc071a000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc071a0a8. > Timecounter "i8254" frequency 1193182 Hz > Timecounter "TSC" frequency 2392948808 Hz > CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2392.95-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 > Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > real memory = 267911168 (255 MB) > avail memory = 252489728 (240 MB) > Pentium Pro MTRR support enabled > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <GATEWA 400 > on motherboard > pcibios: BIOS version 2.10 > Using $PIR table, 11 entries at 0xc00fdf10 > acpi0: power button is handled as a fixed feature programming model. > Timecounter "ACPI-fast" frequency 3579545 Hz > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_tz0: <thermal zone> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <Intel 82845 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0 on pci0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 10 at device 29.0 on pci0 > usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 10 at device 2.0 on pci2 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > pci2: <multimedia, audio> at device 3.0 (no driver attached) > fwohci0: vendor=104c, dev=8026 > fwohci0: <1394 Open Host Controller Interface> mem 0xe8200000-0xe8203fff,0xe8206000-0xe82067ff irq 10 at device 5.0 on pci2 > fwohci0: OHCI version 1.10 (ROM=1) > fwohci0: No. of Isochronous channel is 4. > fwohci0: EUI64 00:e0:b8:04:01:01:ec:f1 > fwohci0: Phy 1394a available S400, 1 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > if_fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:e0:b8:01:ec:f1 > sbp0: <SBP2/SCSI over firewire> on firewire0 > fwohci0: Initiate bus reset > fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x3c00-0x3c3f mem 0xe8205000-0xe8205fff irq 10 at device 8.0 on pci2 > fxp0: Ethernet address 00:e0:b8:50:23:7b > miibus0: <MII bus> on fxp0 > inphy0: <i82562ET 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH3 UDMA100 controller> port 0x1820-0x182f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xe8000000-0xe80003ff at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > pci0: <simple comms> at device 31.6 (no driver attached) > acpi_lid0: <Control Method Lid Switch> on acpi0 > ACPI-1287: *** Error: Method execution failed [\\_SB_.LID_._PSW] (Node 0xc2622e80), AE_NOT_EXIST > acpi_acad0: <AC adapter> on acpi0 > acpi_cmbat0: <Control method Battery> on acpi0 > acpi_button0: <Sleep Button> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 > ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xc0000-0xccfff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 or not responding > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounters tick every 10.000 msec > fwohci0: BUS reset > fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% > cbb0: Unsupported card type detected > ad0: 28615MB <IC25N030ATCS04-0> [58140/16/63] at ata0-master UDMA100 > acd0: CD-RW <QSI CD-RW/DVD-ROM SBW-241> at ata1-master PIO4 > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_TZ_.THRM._TMP] (Node 0xc2622420), AE_ERROR > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR > ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC0.EC0_._Q20] (Node 0xc261d140), AE_AML_NO_RETURN_VALUE > Mounting root from ufs:/dev/ad0s2a > WARNING: / was not properly dismounted > WARNING: /tmp was not properly dismounted > WARNING: /usr was not properly dismounted > /usr: mount pending error: blocks 56 files 1 > /usr: superblock summary recomputed > WARNING: /var was not properly dismounted > interface fwe.1 already present in the KLD 'kernel'! > module_register: module pci/fxp already exists! > Module pci/fxp failed to register: 17 > module_register: module cardbus/fxp already exists! > Module cardbus/fxp failed to register: 17 > module_register: module fxp/miibus already exists! > Module fxp/miibus failed to register: 17 > can't re-use a leaf (fxp_rnr)! > can't re-use a leaf (fxp_noflow)! > drm0: <ATI Radeon LY Mobility M6> port 0x2000-0x20ff mem 0xe8100000-0xe810ffff,0xf0000000-0xf7ffffff irq 10 at device 0.0 on pci1 > info: [drm] AGP at 0xec000000 64MB > info: [drm] Initialized radeon 1.8.0 20020828 on minor 0 > lock order reversal > 1st 0xc2cffd4c vm object (vm object) _at_ vm/vm_object.c:512 > 2nd 0xc082f110 system map (system map) _at_ vm/vm_kern.c:325 > Stack backtrace: > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"Received on Tue May 27 2003 - 13:44:22 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:09 UTC