Hi, Story goes on and once again we replaced mobo with new one and supped latest source. At last we could build vinum volume but then we booted system with new kernel after make world. Now we have lost both slave disks on secondary ata controller. With old kernel we can still see these disks. What's broken this time? Tomppa 1.txt:ad0: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-master 1.txt:ad1: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-slave 1.txt:ad2: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-master 1.txt:ad3: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-slave 1.txt:ad4: <ST3120023A/3.31> ATA-6 disk at ata2-master 1.txt:ad6: <ST3120023A/3.31> ATA-6 disk at ata3-master 2.txt:ad0: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-master 2.txt:ad1: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-slave 2.txt:ad2: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-master 2.txt:ad3: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-slave 2.txt:ad4: <ST3120023A/3.31> ATA-6 disk at ata2-master 2.txt:ad5: <ST3120023A/3.31> ATA-6 disk at ata2-slave 2.txt:ad6: <ST3120023A/3.31> ATA-6 disk at ata3-master 2.txt:ad7: <ST3120023A/3.31> ATA-6 disk at ata3-slave *** 1.txt *** Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel] in 9 seconds... Booting [/boot/kernel/kernel] in 8 seconds... Booting [/boot/kernel/kernel]... |/-\|/-\|/-\|/-\|/-\|/-\|/boot/kernel/acpi.ko text=0x3b504 /-\|/-\|/-\|/-\data=0x16cc+0xee0 |syms=[0x4+0x5c10/+0x4+0x7a31-\] |/-\|/-SMAP type=01 base=0000000000000000 len=000000000009e800 SMAP type=02 base=00000000000f0000 len=0000000000010000 SMAP type=02 base=00000000fec00000 len=0000000001400000 SMAP type=02 base=000000000009e800 len=0000000000001800 SMAP type=01 base=0000000000100000 len=000000001fef0000 SMAP type=03 base=000000001fff3000 len=000000000000d000 SMAP type=04 base=000000001fff0000 len=0000000000003000 Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-CURRENT #0: Thu Oct 2 18:38:43 EEST 2003 _at_iki.fi:/u/FreeBSD/src/sys/i386/compile/TIIKELI Preloaded elf kernel "/boot/kernel/kernel" at 0xc0838000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc08381f4. Calibrating clock(s) ... i8254 clock: 1193203 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2004553448 Hz CPU: Intel(R) Celeron(R) CPU 2.00GHz (2004.55-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 536805376 (511 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009dfff, 643072 bytes (157 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c26000 - 0x000000001f6c9fff, 514473984 bytes (125604 pages) avail memory = 511868928 (488 MB) bios32: Found BIOS32 Service Directory header at 0xc00facf0 bios32: Entry = 0xfb170 (c00fb170) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb1a0 pnpbios: Found PnP BIOS data at 0xc00fbbe0 pnpbios: Entry = f0000:bc10 Rev = 1.0 Other BIOS signatures found: null: <null device, zero device> mem: <memory & I/O> Pentium Pro MTRR support enabled random: <entropy source> netsmb_dev: loaded npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <AOpen AWRDACPI> on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25708086) pcibios: BIOS version 2.10 Using $PIR table, 11 entries at 0xc00fdea0 PCI-Only Interrupts: 9 10 11 12 Location Bus Device Pin Link IRQs slot 1 2 8 A 0x68 3 4 5 7 9 10 11 12 14 15 slot 1 2 8 B 0x69 3 4 5 7 9 10 11 12 14 15 slot 1 2 8 C 0x6a 3 4 5 7 9 10 11 12 14 15 slot 1 2 8 D 0x6b 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 A 0x62 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 B 0x63 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 C 0x68 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 D 0x69 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 A 0x63 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 B 0x68 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 C 0x69 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 D 0x6a 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 A 0x68 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 B 0x69 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 C 0x6a 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 D 0x6b 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 A 0x69 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 B 0x6a 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 C 0x6b 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 D 0x60 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 A 0x6a 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 B 0x6b 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 D 0x61 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 A 0x6b 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 B 0x60 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 C 0x61 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 D 0x62 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 A 0x6a 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 B 0x6b 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 D 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 30 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 30 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 30 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 30 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 31 A 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 31 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 31 C 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 31 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 1 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 1 D 0x63 3 4 5 7 9 10 11 12 14 15 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.3 1.2 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.3 1.0 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.3 1.1 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.0 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.1 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.2 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.3 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .0 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .1 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .2 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .3 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.3 1.2 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.3 1.0 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.3 1.1 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.0 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.1 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.2 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.2 9.3 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .0 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .1 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .2 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 0.1 .3 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base e8000000, size 27, enabled found-> vendor=0x8086, dev=0x2570, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2571, revid=0x02 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x244e, revid=0xc2 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0e (3500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24d0, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 00000000, size 3, enabled map[14]: type 4, range 32, base 00000000, size 2, enabled map[18]: type 4, range 32, base 00000000, size 3, enabled map[1c]: type 4, range 32, base 00000000, size 2, enabled map[20]: type 4, range 32, base 0000f000, size 4, enabled found-> vendor=0x8086, dev=0x24db, revid=0x02 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[20]: type 4, range 32, base 00005000, size 5, enabled pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LNKB) pcib0: slot 31 INTB is routed to irq 10 found-> vendor=0x8086, dev=0x24d3, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 agp0: <Intel 82865 host to AGP bridge> mem 0xe8000000-0xefffffff at device 0.0 o n pci0 agp0: allocating GATT for aperture of size 128M pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xfff00000-0xfffff pcib1: prefetched decode 0xfff00000-0xfffff pci1: <PCI bus> on pcib1 pci1: physical bus=1 pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xa000-0xbfff pcib2: memory decode 0xf0000000-0xfbffffff pcib2: prefetched decode 0xfff00000-0xfffff ---- initial configuration ------------------------ \_SB_.PCI0.LNKE irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .0 \_SB_.PCI0.LNKF irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .1 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .2 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .3 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .0 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .1 \_SB_.PCI0.LNKE irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .2 \_SB_.PCI0.LNKF irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .3 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .0 \_SB_.PCI0.LNKE irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .1 \_SB_.PCI0.LNKF irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .2 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .3 \_SB_.PCI0.LNKE irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .0 \_SB_.PCI0.LNKF irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .1 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .2 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .3 \_SB_.PCI0.LNKF irq 0: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.0 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.1 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.2 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.3 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.0 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.1 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.2 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.3 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.0 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.1 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.2 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.3 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .0 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .1 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .2 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .3 ---- before setting priority for links ------------ \_SB_.PCI0.LNKE: interrupts: 3 4 5 7 9 10 11 12 14 15 penalty: 1990 1990 990 1990 1690 1890 2190 2590 10990 1 0990 references: 4 priority: 0 \_SB_.PCI0.LNKF: interrupts: 3 4 5 7 9 10 11 12 14 15 penalty: 1990 1990 990 1990 1690 1890 2190 2590 10990 1 0990 references: 5 priority: 0 ---- before fixup boot-disabled links ------------- \_SB_.PCI0.LNKF: interrupts: 3 4 5 7 9 10 11 12 14 15 penalty: 1990 1990 990 1990 1690 1890 2190 2590 10990 1 0990 references: 5 priority: 18650 \_SB_.PCI0.LNKE: interrupts: 3 4 5 7 9 10 11 12 14 15 penalty: 1990 1990 990 1990 1690 1890 2190 2590 10990 1 0990 references: 4 priority: 14920 ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \_SB_.PCI0.LNKE irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .0 \_SB_.PCI0.LNKF irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .1 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .2 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.8 .3 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .0 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .1 \_SB_.PCI0.LNKE irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .2 \_SB_.PCI0.LNKF irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.4 .3 \_SB_.PCI0.LNKD irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .0 \_SB_.PCI0.LNKE irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .1 \_SB_.PCI0.LNKF irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .2 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.5 .3 \_SB_.PCI0.LNKE irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .0 \_SB_.PCI0.LNKF irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .1 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .2 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.9 .3 \_SB_.PCI0.LNKF irq 5: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.0 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.1 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.2 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 0.3 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.0 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.1 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.2 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 1.3 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.0 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.1 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.2 \_SB_.PCI0.LNKC irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.1 2.3 \_SB_.PCI0.LNK0 irq 12: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .0 \_SB_.PCI0.LNK1 irq 9: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .1 \_SB_.PCI0.LNKA irq 11: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .2 \_SB_.PCI0.LNKB irq 10: [ 3 4 5 7 9 10 11 12 14 15] low,level,sharable 2.7 .3 pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 4, range 32, base 0000a000, size 8, enabled map[14]: type 1, range 32, base f8020000, size 12, enabled pcib2: matched entry for 2.4.INTA (source \_SB_.PCI0.LNKC) pcib2: slot 4 INTA is routed to irq 11 found-> vendor=0x9004, dev=0x8178, revid=0x00 bus=2, slot=4, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns) intpin=a, irq=11 map[10]: type 4, range 32, base 0000a400, size 3, enabled map[14]: type 4, range 32, base 0000a800, size 2, enabled map[18]: type 4, range 32, base 0000ac00, size 3, enabled map[1c]: type 4, range 32, base 0000b000, size 2, enabled map[20]: type 4, range 32, base 0000b400, size 6, enabled map[24]: type 1, range 32, base f8000000, size 17, enabled pcib2: matched entry for 2.5.INTA (source \_SB_.PCI0.LNKD) pcib2: slot 5 INTA is routed to irq 10 found-> vendor=0x105a, dev=0x4d30, revid=0x02 bus=2, slot=5, func=0 class=01-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 1 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000b800, size 6, enabled pcib2: matched entry for 2.11.INTA (source \_SB_.PCI0.LNK0) pcib2: slot 11 INTA is routed to irq 12 found-> vendor=0x10b7, dev=0x9050, revid=0x00 bus=2, slot=11, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns) intpin=a, irq=12 map[10]: type 1, range 32, base f0000000, size 25, enabled pcib2: matched entry for 2.12.INTA (source \_SB_.PCI0.LNK1) pcib2: slot 12 INTA is routed to irq 9 found-> vendor=0x5333, dev=0x88f0, revid=0x00 bus=2, slot=12, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0083, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xa000-0xa0ff mem 0xf8020000-0xf802 0fff irq 11 at device 4.0 on pci2 ahc0: Defaulting to MEMIO off pcib2: device ahc0 requested decoded I/O range 0xa000-0xa0ff ahc0: Reading SEEPROM...done. ahc0: internal 50 cable not present, internal 68 cable is present ahc0: external cable not present ahc0: BIOS eeprom is present ahc0: High byte termination Enabled ahc0: Low byte termination Enabled ahc0: Downloading Sequencer Program... 448 instructions downloaded ahc0: Features 0x5, Bugs 0x25, Flags 0x20481540 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs atapci0: <Promise PDC20267 UDMA100 controller> port 0xb400-0xb43f,0xb000-0xb003, 0xac00-0xac07,0xa800-0xa803,0xa400-0xa407 mem 0xf8000000-0xf801ffff irq 10 at de vice 5.0 on pci2 pcib2: device atapci0 requested decoded I/O range 0xb400-0xb43f atapci0: [MPSAFE] pcib2: device atapci0 requested decoded I/O range 0xa400-0xa407 pcib2: device atapci0 requested decoded I/O range 0xa800-0xa803 pcib2: device atapci0 requested decoded I/O range 0xa802-0xa802 ata2: reset tp1 mask=03 ostat0=50 ostat1=50 ata2-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata2-slave: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata2-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata2-slave: stat=0x10 err=0x00 lsb=0x00 msb=0x00 ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 mask=03 stat0=50 stat1=10 devices=0x1<ATA_MASTER> ata2: at 0xa400 on atapci0 ata2: [MPSAFE] pcib2: device atapci0 requested decoded I/O range 0xac00-0xac07 pcib2: device atapci0 requested decoded I/O range 0xb000-0xb003 pcib2: device atapci0 requested decoded I/O range 0xb002-0xb002 ata3: reset tp1 mask=03 ostat0=50 ostat1=50 ata3-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata3-slave: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata3-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata3-slave: stat=0x10 err=0x00 lsb=0x00 msb=0x00 ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 mask=03 stat0=50 stat1=10 devices=0x1<ATA_MASTER> ata3: at 0xac00 on atapci0 ata3: [MPSAFE] xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xb800-0xb83f irq 12 at device 11.0 on pci2 pcib2: device xl0 requested decoded I/O range 0xb800-0xb83f xl0: using port I/O xl0: Ethernet address: 00:60:08:0a:d4:1d xl0: media options word: e040 xl0: found MII/AUTO miibus0: <MII bus> on xl0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: bpf attached pci2: <display, VGA> at device 12.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <Intel ICH5 UDMA100 controller> port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0- 0x7 at device 31.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=50 ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata0-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER> ata0: at 0x1f0 irq 14 on atapci1 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=50 ostat1=50 ata1-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata1-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata1: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER> ata1: at 0x170 irq 15 on atapci1 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0 x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold sio0: irq maps: 0x41 0x51 0x41 0x41 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console sio1: irq maps: 0x41 0x49 0x41 0x41 sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A unknown: not probed (disabled) ppc0: using extended I/O port range ppc0: SPP ppc0 port 0x778-0x77b,0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 unknown: not probed (disabled) unknown: not probed (disabled) atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0067 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000 psm0: unable to allocate IRQ unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 vt: vt0 already exists; skipping it sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xcf000-0xd0fff,0xc8000-0xcefff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 2004553448 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached ata1: spurious interrupt - status=0x50 error=0x01 acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0% ata0-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ad0: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad0 dp=0xc48f9e70 ad0: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-master ad0: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ar: FreeBSD check1 failed [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 160039240704 end 160039272959 ad1: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad1 dp=0xc48f9a70 ad1: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-slave ad1: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad1: 16 secs/int, 1 depth queue, UDMA100 ar: FreeBSD check1 failed GEOM: Configure ad0s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad0s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad0s1d, start 0 length 160039240704 end 160039240703 GEOM: new disk ad1 ata1-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad1s1, start 32256 length 160039240704 end 160039272959 ad2: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad2 dp=0xc48f9270 ad2: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-master ad2: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad2: 16 secs/int, 1 depth queue, UDMA100 GEOM: Configure ad1s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad1s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad1s1d, start 0 length 160039240704 end 160039240703 GEOM: new disk ad2 ar: FreeBSD check1 failed ad3: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad3 dp=0xc48fe070 ad3: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-slave ad3: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad3: 16 secs/int, 1 depth queue, UDMA100 ar: FreeBSD check1 failed [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad2s1, start 32256 length 160039240704 end 160039272959 ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin GEOM: new disk ad3 GEOM: Configure ad2s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad2s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad2s1d, start 0 length 160039240704 end 160039240703 ad4: setting UDMA100 on Promise PDC20267 chip GEOM: create disk ad4 dp=0xc48fa770 ad4: <ST3120023A/3.31> ATA-6 disk at ata2-master ad4: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad4: 16 secs/int, 1 depth queue, UDMA100 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad3s1, start 32256 length 160039240704 end 160039272959 ar: Promise check1 failed GEOM: new disk ad4 ata3-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin GEOM: Configure ad3s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad3s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad3s1d, start 0 length 160039240704 end 160039240703 ad6: setting UDMA100 on Promise PDC20267 chip GEOM: create disk ad6 dp=0xc48fe170 ad6: <ST3120023A/3.31> ATA-6 disk at ata3-master ad6: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad6: 16 secs/int, 1 depth queue, UDMA100 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad4s1, start 32256 length 120031478784 end 120031511039 ar: Promise check1 failed Waiting 8 seconds for SCSI devices to settle (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. GEOM: new disk ad6 GEOM: Configure ad4s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad4s1d, start 0 length 120031478784 end 120031478783 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad6s1, start 32256 length 120031478784 end 120031511039 GEOM: Configure ad6s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad6s1d, start 0 length 120031478784 end 120031478783 (probe0:ahc0:0:0:0): Retrying Command (ahc0:A:0:0): Sending WDTR 1 (ahc0:A:0:0): Received WDTR 1 filtered to 1 ahc0: target 0 using 16bit transfers (ahc0:A:0:0): Sending SDTR period c, offset 8 (ahc0:A:0:0): Received SDTR period c, offset 8 Filtered to period c, offset 8 ahc0: target 0 synchronous at 20.0MHz, offset = 0x8 GEOM: create disk da0 dp=0xc4913050 pass0 at ahc0 bus 0 target 0 lun 0 pass0: <SEAGATE ST19171W 0023> Fixed Direct Access SCSI-2 device pass0: Serial Number LA691693 pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enable d da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST19171W 0023> Fixed Direct Access SCSI-2 device da0: Serial Number LA691693 da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled da0: 8683MB (17783112 512 byte sectors: 255H 63S/T 1106C) GEOM: new disk da0 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:17767827 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure da0s1, start 32256 length 9097127424 end 9097159679 GEOM: Configure da0s1a, start 524288000 length 1073741824 end 1598029823 GEOM: Configure da0s1b, start 0 length 524288000 end 524287999 GEOM: Configure da0s1c, start 0 length 9097127424 end 9097127423 GEOM: Configure da0s1d, start 1598029824 length 7499097600 end 9097127423 Mounting root from ufs:/dev/da0s1a start_init: trying /sbin/init Loading configuration files. Entropy harvesting: interrupts ethernet point_to_point. kernel dumps on /dev/da0s1b vinum: loaded vinum: reading configuration from /dev/ad0s1d vinum: updating configuration from /dev/ad1s1d vinum: updating configuration from /dev/ad2s1d vinum: updating configuration from /dev/ad3s1d vinum: updating configuration from /dev/ad4s1d vinum: updating configuration from /dev/ad6s1d swapon: adding /dev/da0s1b as swap device Starting file system checks: /dev/da0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/da0s1a: clean, 262489 free (15337 frags, 30894 blocks, 3.0% fragmentation) /dev/da0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/da0s1d: clean, 1765912 free (24888 frags, 217628 blocks, 0.7% fragmentation ) Setting hostname: iki.fi. xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet 193.64.243.175 netmask 0xffffffe0 broadcast 193.64.243.191 inet6 fe80::260:8ff:fe0a:d41d%xl0 prefixlen 64 tentative scopeid 0x1 ether 00:60:08:0a:d4:1d media: Ethernet autoselect (100baseTX <full-duplex>) status: active lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 inet 127.0.0.1 netmask 0xff000000 add net default: gateway 193.64.243.190 Additional routing options:. add net ::ffff:0.0.0.0: gateway ::1 add net ::0.0.0.0: gateway ::1 net.inet6.ip6.forwarding: 0 -> 0 ifconfig: prefixlen:260:8ff:fe0a:d41d: bad value ifconfig: 64:260:8ff:fe0a:d41d: bad value xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet6 fe80::260:8ff:fe0a:d41d%xl0 prefixlen 64 tentative scopeid 0x1 inet6 2001:670:a0:11:: prefixlen 64 tentative lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 add net fe80::: gateway ::1 add net ff02::: gateway ::1 IPv4 mapped IPv6 address support=NO hw.bus.devctl_disable: 0 -> 1 Mounting NFS file systems:. Starting syslogd. Oct 3 21:50:39 tiikeli syslogd: kernel boot file is /boot/kernel/kernel Checking for core dump... savecore: no dumps found Starting ntpdate. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout Starting usbd. No USB host controllers found Starting local daemons:. Updating motd. Starting ntpd. Configuring syscons: blanktime. Starting sshd. Initial i386 initialization:. Additional ABI support:. Starting cron. Local package initialization: proftpd Samba (skipping setiathome.sh, not executa ble). Additional TCP options:. Starting background file system checks in 60 seconds. Fri Oct 3 21:50:56 EEST 2003 Console: serial port *** 2.txt *** OK unload OK load /boot/kernel.old/kernel /boot/kernel.old/kernel text=0x2e50e4 data=0x2e854+0x51be8 syms=[0x4+0x39f60+0x4 +0x46e72] OK boot /boot/kernel/acpi.ko text=0x3b504 data=0x16cc+0xee0 syms=[0x4+0x5c10+0x4+0x7a3]- SMAP type=01 base=0000000000000000 len=000000000009e800 SMAP type=02 base=00000000000f0000 len=0000000000010000 SMAP type=02 base=00000000fec00000 len=0000000001400000 SMAP type=02 base=000000000009e800 len=0000000000001800 SMAP type=01 base=0000000000100000 len=000000001fef0000 SMAP type=03 base=000000001fff3000 len=000000000000d000 SMAP type=04 base=000000001fff0000 len=0000000000003000 Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-CURRENT #0: Sat Sep 13 01:27:45 EEST 2003 _at_iki.fi:/u/FreeBSD/src/sys/i386/compile/TIIKELI Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc0536000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05361f8. link_elf: symbol bus_config_intr_desc undefined KLD file acpi.ko - could not finalize loading Calibrating clock(s) ... i8254 clock: 1193201 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2004558312 Hz CPU: Intel(R) Celeron(R) CPU 2.00GHz (2004.56-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 536805376 (511 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009dfff, 643072 bytes (157 pages) 0x000000000055d000 - 0x000000001f6c9fff, 521588736 bytes (127341 pages) avail memory = 515796992 (491 MB) bios32: Found BIOS32 Service Directory header at 0xc00facf0 bios32: Entry = 0xfb170 (c00fb170) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb1a0 pnpbios: Found PnP BIOS data at 0xc00fbbe0 pnpbios: Entry = f0000:bc10 Rev = 1.0 Other BIOS signatures found: random: <entropy source> netsmb_dev: loaded null: <null device, zero device> mem: <memory & I/O> Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25708086) pcibios: BIOS version 2.10 Using $PIR table, 11 entries at 0xc00fdea0 PCI-Only Interrupts: 9 10 11 12 Location Bus Device Pin Link IRQs slot 1 2 8 A 0x68 3 4 5 7 9 10 11 12 14 15 slot 1 2 8 B 0x69 3 4 5 7 9 10 11 12 14 15 slot 1 2 8 C 0x6a 3 4 5 7 9 10 11 12 14 15 slot 1 2 8 D 0x6b 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 A 0x62 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 B 0x63 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 C 0x68 3 4 5 7 9 10 11 12 14 15 slot 2 2 4 D 0x69 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 A 0x63 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 B 0x68 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 C 0x69 3 4 5 7 9 10 11 12 14 15 slot 3 2 5 D 0x6a 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 A 0x68 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 B 0x69 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 C 0x6a 3 4 5 7 9 10 11 12 14 15 slot 4 2 9 D 0x6b 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 A 0x69 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 B 0x6a 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 C 0x6b 3 4 5 7 9 10 11 12 14 15 slot 5 2 10 D 0x60 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 A 0x6a 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 B 0x6b 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 6 2 11 D 0x61 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 A 0x6b 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 B 0x60 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 C 0x61 3 4 5 7 9 10 11 12 14 15 slot 7 2 12 D 0x62 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 A 0x6a 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 B 0x6b 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 8 2 7 D 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 30 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 30 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 30 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 30 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 31 A 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 31 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 31 C 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 31 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 1 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 1 D 0x63 3 4 5 7 9 10 11 12 14 15 pcib0: <Host to PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base e8000000, size 27, enabled found-> vendor=0x8086, dev=0x2570, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2571, revid=0x02 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x244e, revid=0xc2 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0e (3500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24d0, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 00000000, size 3, enabled map[14]: type 4, range 32, base 00000000, size 2, enabled map[18]: type 4, range 32, base 00000000, size 3, enabled map[1c]: type 4, range 32, base 00000000, size 2, enabled map[20]: type 4, range 32, base 0000f000, size 4, enabled found-> vendor=0x8086, dev=0x24db, revid=0x02 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[20]: type 4, range 32, base 00005000, size 5, enabled pci_cfgintr_valid: BIOS irq 10 is valid pci_cfgintr: 0:31 INTB BIOS irq 10 found-> vendor=0x8086, dev=0x24d3, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 agp0: <Intel 82865 host to AGP bridge> mem 0xe8000000-0xefffffff at device 0.0 o n pci0 agp0: allocating GATT for aperture of size 128M pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xfff00000-0xfffff pcib1: prefetched decode 0xfff00000-0xfffff pci1: <PCI bus> on pcib1 pci1: physical bus=1 pcib2: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xa000-0xbfff pcib2: memory decode 0xf0000000-0xfbffffff pcib2: prefetched decode 0xfff00000-0xfffff pci2: <PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 4, range 32, base 0000a000, size 8, enabled map[14]: type 1, range 32, base f8020000, size 12, enabled pci_cfgintr_valid: BIOS irq 11 is valid pci_cfgintr: 2:4 INTA BIOS irq 11 found-> vendor=0x9004, dev=0x8178, revid=0x00 bus=2, slot=4, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns) intpin=a, irq=11 map[10]: type 4, range 32, base 0000a400, size 3, enabled map[14]: type 4, range 32, base 0000a800, size 2, enabled map[18]: type 4, range 32, base 0000ac00, size 3, enabled map[1c]: type 4, range 32, base 0000b000, size 2, enabled map[20]: type 4, range 32, base 0000b400, size 6, enabled map[24]: type 1, range 32, base f8000000, size 17, enabled pci_cfgintr_valid: BIOS irq 10 is valid pci_cfgintr: 2:5 INTA BIOS irq 10 found-> vendor=0x105a, dev=0x4d30, revid=0x02 bus=2, slot=5, func=0 class=01-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 1 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000b800, size 6, enabled pci_cfgintr_valid: BIOS irq 12 is valid pci_cfgintr: 2:11 INTA BIOS irq 12 found-> vendor=0x10b7, dev=0x9050, revid=0x00 bus=2, slot=11, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns) intpin=a, irq=12 map[10]: type 1, range 32, base f0000000, size 25, enabled pci_cfgintr_valid: BIOS irq 9 is valid pci_cfgintr: 2:12 INTA BIOS irq 9 found-> vendor=0x5333, dev=0x88f0, revid=0x00 bus=2, slot=12, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0083, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xa000-0xa0ff mem 0xf8020000-0xf802 0fff irq 11 at device 4.0 on pci2 ahc0: Defaulting to MEMIO off pcib2: device ahc0 requested decoded I/O range 0xa000-0xa0ff ahc0: Reading SEEPROM...done. ahc0: internal 50 cable not present, internal 68 cable is present ahc0: external cable not present ahc0: BIOS eeprom is present ahc0: High byte termination Enabled ahc0: Low byte termination Enabled ahc0: Downloading Sequencer Program... 448 instructions downloaded ahc0: Features 0x5, Bugs 0x25, Flags 0x20481540 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs atapci0: <Promise PDC20267 UDMA100 controller> port 0xb400-0xb43f,0xb000-0xb003, 0xac00-0xac07,0xa800-0xa803,0xa400-0xa407 mem 0xf8000000-0xf801ffff irq 10 at de vice 5.0 on pci2 pcib2: device atapci0 requested decoded I/O range 0xb400-0xb43f atapci0: [MPSAFE] pcib2: device atapci0 requested decoded I/O range 0xa400-0xa407 pcib2: device atapci0 requested decoded I/O range 0xa800-0xa803 pcib2: device atapci0 requested decoded I/O range 0xa802-0xa802 ata2: reset tp1 mask=03 ostat0=50 ostat1=50 ata2-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata2-slave: stat=0x80 err=0x90 lsb=0x90 msb=0x90 ata2-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata2-slave: stat=0x90 err=0x00 lsb=0x00 msb=0x00 ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 mask=03 stat0=50 stat1=10 devices=0x1<ATA_MASTER> ata2-slave: ATA err=0x01 lsb=0xa5 ata2: reset tp3 devices=0x3<ATA_SLAVE,ATA_MASTER> ata2: at 0xa400 on atapci0 ata2: [MPSAFE] pcib2: device atapci0 requested decoded I/O range 0xac00-0xac07 pcib2: device atapci0 requested decoded I/O range 0xb000-0xb003 pcib2: device atapci0 requested decoded I/O range 0xb002-0xb002 ata3: reset tp1 mask=03 ostat0=50 ostat1=50 ata3-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata3-slave: stat=0x80 err=0x90 lsb=0x90 msb=0x90 ata3-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata3-slave: stat=0x90 err=0x00 lsb=0x00 msb=0x00 ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 mask=03 stat0=50 stat1=10 devices=0x1<ATA_MASTER> ata3-slave: ATA err=0x01 lsb=0xa5 ata3: reset tp3 devices=0x3<ATA_SLAVE,ATA_MASTER> ata3: at 0xac00 on atapci0 ata3: [MPSAFE] xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xb800-0xb83f irq 12 at device 11.0 on pci2 pcib2: device xl0 requested decoded I/O range 0xb800-0xb83f xl0: using port I/O xl0: Ethernet address: 00:60:08:0a:d4:1d xl0: media options word: e040 xl0: found MII/AUTO miibus0: <MII bus> on xl0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: bpf attached pci2: <display, VGA> at device 12.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <Intel ICH5 UDMA100 controller> port 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0- 0x7 at device 31.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=50 ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata0-slave: stat=0x80 err=0x01 lsb=0x00 msb=0x00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER> ata0: reset tp3 devices=0x3<ATA_SLAVE,ATA_MASTER> ata0: at 0x1f0 irq 14 on atapci1 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=50 ostat1=50 ata1-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata1-slave: stat=0x80 err=0x01 lsb=0x00 msb=0x00 ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata1: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER> ata1: reset tp3 devices=0x3<ATA_SLAVE,ATA_MASTER> ata1: at 0x170 irq 15 on atapci1 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 pnpbios: 17 devices, largest 92 bytes PNP0000: adding irq mask 0x4 PNP0000: adding io range 0x20-0x21, size=0x2, align=0 PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0 pnpbios: handle 0 device ID PNP0000 (0000d041) PNP0200: adding dma mask 0x10 PNP0200: adding io range 0-0xf, size=0x10, align=0 PNP0200: adding io range 0x81-0x83, size=0x3, align=0 PNP0200: adding io range 0x87-0x87, size=0x1, align=0 PNP0200: adding io range 0x89-0x8b, size=0x3, align=0 PNP0200: adding io range 0x8f-0x91, size=0x3, align=0 PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0 pnpbios: handle 1 device ID PNP0200 (0002d041) PNP0100: adding irq mask 0x1 PNP0100: adding io range 0x40-0x43, size=0x4, align=0 pnpbios: handle 2 device ID PNP0100 (0001d041) PNP0b00: adding irq mask 0x100 PNP0b00: adding io range 0x70-0x71, size=0x2, align=0 pnpbios: handle 3 device ID PNP0b00 (000bd041) PNP0303: adding irq mask 0x2 PNP0303: adding io range 0x60-0x60, size=0x1, align=0 PNP0303: adding io range 0x64-0x64, size=0x1, align=0 pnpbios: handle 4 device ID PNP0303 (0303d041) PNP0800: adding io range 0x61-0x61, size=0x1, align=0 pnpbios: handle 5 device ID PNP0800 (0008d041) PNP0c04: adding irq mask 0x2000 PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0 pnpbios: handle 6 device ID PNP0c04 (040cd041) INT0800: adding fixed memory32 range 0xffb80000-0xffbfffff, size=0x80000 pnpbios: handle 7 device ID INT0800 (0008d425) PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000 PNP0c01: adding fixed memory32 range 0xffb00000-0xffb7ffff, size=0x80000 PNP0c01: adding fixed memory32 range 0xfff00000-0xffffffff, size=0x100000 PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000 PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000 PNP0c01: adding fixed memory32 range 0x100000-0xffffff, size=0xf00000 pnpbios: handle 8 device ID PNP0c01 (010cd041) PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000 PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000 PNP0c02: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000 PNP0c02: adding fixed memory32 range 0xd1000-0xd3fff, size=0x3000 pnpbios: handle 9 device ID PNP0c02 (020cd041) PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0 PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0 PNP0a03: adding io range 0x4000-0x40bf, size=0xc0, align=0 pnpbios: handle 10 device ID PNP0a03 (030ad041) PNP0501: adding irq mask 0x10 PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0 pnpbios: handle 12 device ID PNP0501 (0105d041) PNP0700: adding dma mask 0x4 PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0 PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0 PNP0700: adding irq mask 0x40 pnpbios: handle 13 device ID PNP0700 (0007d041) PNP0400: adding irq mask 0x80 PNP0400: adding io range 0x378-0x37f, size=0x8, align=0 PNP0400: adding io range 0x778-0x77b, size=0x4, align=0 pnpbios: handle 14 device ID PNP0400 (0004d041) PNP0501: adding irq mask 0x8 PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0 pnpbios: handle 16 device ID PNP0501 (0105d041) PNPb006: adding irq mask 0x20 PNPb006: adding io range 0x330-0x331, size=0x2, align=0 pnpbios: handle 17 device ID PNPb006 (06b0d041) PNPb02f: adding io range 0x201-0x207, size=0x7, align=0 PNPb02f: adding io range 0x200-0x200, size=0x1, align=0 pnpbios: handle 18 device ID PNPb02f (2fb0d041) vt: vt0 already exists; skipping it sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xcf000-0xd0fff,0xc8000-0xcefff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0067 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000 psm0: current command byte:0067 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 psm0: failed to reset the aux device. bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f 0-0x3f5 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0: parallel port found at 0x378 ppc0: using extended I/O port range ppc0: SPP ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 ppi0: <Parallel I/O> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0: irq maps: 0x41 0x51 0x41 0x41 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1: irq maps: 0x41 0x49 0x41 0x41 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices unknown: <PNP0303> can't assign resources (port) unknown: <PNP0303> at port 0x60 on isa0 unknown: <PNP0800> failed to probe at port 0x61 on isa0 unknown: <INT0800> failed to probe at iomem 0xffb80000-0xffbfffff on isa0 unknown: <PNP0501> can't assign resources (port) unknown: <PNP0501> at port 0x3f8-0x3ff on isa0 unknown: <PNP0700> can't assign resources (port) unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0 unknown: <PNP0400> can't assign resources (port) unknown: <PNP0400> at port 0x378-0x37f on isa0 unknown: <PNP0501> can't assign resources (port) unknown: <PNP0501> at port 0x2f8-0x2ff on isa0 unknown: <PNPb006> failed to probe at port 0x330-0x331 irq 5 on isa0 unknown: <PNPb02f> failed to probe at port 0x200,0x201-0x207 on isa0 Device configuration finished. procfs registered Timecounter "TSC" frequency 2004558312 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached ata1: spurious interrupt - status=0x50 error=0x01 reason=0x01 ata0-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ad0: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad0 dp=0xc4110070 ad0: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-master ad0: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ar: FreeBSD check1 failed [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 160039240704 end 160039272959 ad1: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad1 dp=0xc404bc70 ad1: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata0-slave ad1: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad1: 16 secs/int, 1 depth queue, UDMA100 ar: FreeBSD check1 failed GEOM: Configure ad0s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad0s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad0s1d, start 0 length 160039240704 end 160039240703 GEOM: new disk ad1 ata1-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad1s1, start 32256 length 160039240704 end 160039272959 ad2: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad2 dp=0xc4133e70 ad2: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-master ad2: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad2: 16 secs/int, 1 depth queue, UDMA100 GEOM: Configure ad1s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad1s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad1s1d, start 0 length 160039240704 end 160039240703 GEOM: new disk ad2 ar: FreeBSD check1 failed ad3: setting UDMA100 on Intel ICH5 chip GEOM: create disk ad3 dp=0xc4133770 ad3: <SAMSUNG SV1604N/TR100-23> ATA-7 disk at ata1-slave ad3: 152627MB (312581808 sectors), 310101 C, 16 H, 63 S, 512 B ad3: 16 secs/int, 1 depth queue, UDMA100 ar: FreeBSD check1 failed [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad2s1, start 32256 length 160039240704 end 160039272959 ata2-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin GEOM: new disk ad3 ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin GEOM: Configure ad2s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad2s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad2s1d, start 0 length 160039240704 end 160039240703 ad4: setting UDMA100 on Promise PDC20267 chip GEOM: create disk ad4 dp=0xc4133470 ad4: <ST3120023A/3.31> ATA-6 disk at ata2-master ad4: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad4: 16 secs/int, 1 depth queue, UDMA100 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:312576642 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad3s1, start 32256 length 160039240704 end 160039272959 ar: Promise check1 failed ad5: setting UDMA100 on Promise PDC20267 chip GEOM: create disk ad5 dp=0xc4133d70 ad5: <ST3120023A/3.31> ATA-6 disk at ata2-slave ad5: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad5: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad4 ar: Promise check1 failed GEOM: Configure ad3s1a, start 8192 length 160039232512 end 160039240703 GEOM: Configure ad3s1c, start 0 length 160039240704 end 160039240703 GEOM: Configure ad3s1d, start 0 length 160039240704 end 160039240703 GEOM: new disk ad5 ata3-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata3-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad4s1, start 32256 length 120031478784 end 120031511039 ad6: setting UDMA100 on Promise PDC20267 chip GEOM: create disk ad6 dp=0xc414cb70 ad6: <ST3120023A/3.31> ATA-6 disk at ata3-master ad6: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad6: 16 secs/int, 1 depth queue, UDMA100 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad5s1, start 32256 length 120031478784 end 120031511039 ar: Promise check1 failed ad7: setting UDMA100 on Promise PDC20267 chip GEOM: create disk ad7 dp=0xc414c070 ad7: <ST3120023A/3.31> ATA-6 disk at ata3-slave ad7: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad7: 16 secs/int, 1 depth queue, UDMA100 GEOM: Configure ad4s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad4s1d, start 0 length 120031478784 end 120031478783 GEOM: new disk ad6 ar: Promise check1 failed Waiting 8 seconds for SCSI devices to settle (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. GEOM: Configure ad5s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad5s1d, start 0 length 120031478784 end 120031478783 GEOM: new disk ad7 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad6s1, start 32256 length 120031478784 end 120031511039 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/14/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad7s1, start 32256 length 120031478784 end 120031511039 GEOM: Configure ad6s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad6s1d, start 0 length 120031478784 end 120031478783 GEOM: Configure ad7s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad7s1d, start 0 length 120031478784 end 120031478783 (probe0:ahc0:0:0:0): Retrying Command (ahc0:A:0:0): Sending WDTR 1 (ahc0:A:0:0): Received WDTR 1 filtered to 1 ahc0: target 0 using 16bit transfers (ahc0:A:0:0): Sending SDTR period c, offset 8 (ahc0:A:0:0): Received SDTR period c, offset 8 Filtered to period c, offset 8 ahc0: target 0 synchronous at 20.0MHz, offset = 0x8 GEOM: create disk da0 dp=0xc414e850 pass0 at ahc0 bus 0 target 0 lun 0 pass0: <SEAGATE ST19171W 0023> Fixed Direct Access SCSI-2 device pass0: Serial Number LA691693 pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enable d da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST19171W 0023> Fixed Direct Access SCSI-2 device da0: Serial Number LA691693 da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled da0: 8683MB (17783112 512 byte sectors: 255H 63S/T 1106C) GEOM: new disk da0 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:17767827 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure da0s1, start 32256 length 9097127424 end 9097159679 GEOM: Configure da0s1a, start 524288000 length 1073741824 end 1598029823 GEOM: Configure da0s1b, start 0 length 524288000 end 524287999 GEOM: Configure da0s1c, start 0 length 9097127424 end 9097127423 GEOM: Configure da0s1d, start 1598029824 length 7499097600 end 9097127423 Mounting root from ufs:/dev/da0s1a start_init: trying /sbin/init Loading configuration files. Entropy harvesting: interrupts ethernet point_to_point. ps: kvm_getprocs: Invalid argument ps: kvm_getprocs: Invalid argument kernel dumps on /dev/da0s1b swapon: adding /dev/da0s1b as swap device Starting file system checks: /dev/da0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/da0s1a: clean, 262532 free (15348 frags, 30898 blocks, 3.0% fragmentation) /dev/da0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/da0s1d: clean, 1765915 free (24851 frags, 217633 blocks, 0.7% fragmentation ) Setting hostname: iki.fi. xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet 193.64.243.175 netmask 0xffffffe0 broadcast 193.64.243.191 inet6 fe80::260:8ff:fe0a:d41d%xl0 prefixlen 64 tentative scopeid 0x1 ether 00:60:08:0a:d4:1d media: Ethernet autoselect (100baseTX <full-duplex>) status: active lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 inet 127.0.0.1 netmask 0xff000000 add net default: gateway 193.64.243.190 Additional routing options:. add net ::ffff:0.0.0.0: gateway ::1 add net ::0.0.0.0: gateway ::1 net.inet6.ip6.forwarding: 0 -> 0 ifconfig: prefixlen:260:8ff:fe0a:d41d: bad value ifconfig: 64:260:8ff:fe0a:d41d: bad value xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet6 fe80::260:8ff:fe0a:d41d%xl0 prefixlen 64 tentative scopeid 0x1 inet6 2001:670:a0:11:: prefixlen 64 tentative lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 add net fe80::: gateway ::1 add net ff02::: gateway ::1 IPv4 mapped IPv6 address support=NO hw.bus.devctl_disable: 0 -> 1 Mounting NFS file systems:. Starting syslogd. Checking for core dump... savecore: no dumps found Starting ntpdate. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout Starting usbd. No USB host controllers found Starting local daemons:. Updating motd. Starting ntpd. Configuring syscons: blanktime. Starting sshd. Initial i386 initialization:. Additional ABI support:. Starting cron. Local package initialization: proftpd Samba (skipping setiathome.sh, not executa ble). Additional TCP options:.Received on Fri Oct 03 2003 - 10:09:33 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:24 UTC