panic: lockmgr: locking against myself

I was overly optimistic and tried the cutting edge kernel for my new
server, but it didn't work out.  Now I'm trying to run 5.2.1-RELEASE-p9,
but it keeps panicing on "lockmgr: locking against myself".  I did some
searching, but I can't find any helpful information on how to fix this.
I don't have any debug info from the crash right bow, but I do have my dmesg
showing the current system and I could probably get debug info if I
needed it.  My kernel is a copy of GENERIC with the addition of just one
option, QUOTA.  Any advice (including a reminder of where the page is
describing how to pull the debug info out of the kernel panic) would be
appreciated.  :)

Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RELEASE-p9 #5: Thu Aug 12 15:24:56 MDT 2004
    wcolburn_at_newuserhost.NMT.edu:/usr/obj/usr/src/sys/USERHOST
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a36000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a361f4.
ACPI APIC Table: <DELL   PE2650  >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.97-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1073676288 (1023 MB)
avail memory = 1033510912 (985 MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
ioapic0: Changing APIC ID to 4
ioapic1: Changing APIC ID to 5
ioapic2: Changing APIC ID to 6
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   PE2650  > on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fc480
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_cpu2: <CPU> on acpi0
acpi_cpu3: <CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 15 INTA is routed to irq 5
pci0: <unknown> at device 4.0 (no driver attached)
pci0: <unknown> at device 4.1 (no driver attached)
pci0: <unknown> at device 4.2 (no driver attached)
pci0: <display, VGA> at device 14.0 (no driver attached)
atapci0: <ServerWorks CSB5 UDMA100 controller> port 0x8b0-0x8bf,0x8d8-0x8db,0x8d0-0x8d7,0x8c8-0x8cb,0x8c0-0x8c7 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: simplex device, DMA on primary only
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
ohci0: <OHCI (generic) USB controller> mem 0xfe100000-0xfe100fff irq 5 at device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
isab0: <PCI-ISA bridge> at device 15.3 on pci0
isa0: <ISA bus> on isab0
pcib1: <ACPI Host-PCI bridge> on acpi0
pci4: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 8.0 on pci4
pci5: <ACPI PCI bus> on pcib2
pci5: <mass storage, SCSI> at device 6.0 (no driver attached)
pci5: <mass storage, SCSI> at device 6.1 (no driver attached)
aac0: <Dell PERC 3/Di> mem 0xf0000000-0xf7ffffff irq 30 at device 8.1 on pci4
aac0: [MPSAFE]
aac0: i960RX 100MHz, 118MB cache memory, optional battery present
aac0: Kernel 2.7-1, Build 3170, S/N 7041d3
aac0: Supported Options=75c<WCACHE,DATA64,HOSTTIME,WINDOW4GB,SOFTERR,NORECOND,SGMAP64>
pcib3: <ACPI Host-PCI bridge> on acpi0
pci3: <ACPI PCI bus> on pcib3
bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem 0xfcd10000-0xfcd1ffff irq 28 at device 6.0 on pci3
bge0: Ethernet address: 00:0b:db:a8:86:37
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge1: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem 0xfcd00000-0xfcd0ffff irq 29 at device 8.0 on pci3
bge1: Ethernet address: 00:0b:db:a8:86:38
miibus1: <MII bus> on bge1
brgphy1: <BCM5701 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
pcib4: <ACPI Host-PCI bridge> on acpi0
pci2: <ACPI PCI bus> on pcib4
pcib5: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib5
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xdc00-0xdcff mem 0xfcf00000-0xfcf00fff irq 16 at device 6.0 on pci1
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
orm0: <Option ROMs> at iomem 0xec000-0xeffff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acd0: CDROM <TEAC CD-ROM CD-224E> at ata0-master PIO4
Waiting 15 seconds for SCSI devices to settle
aacd0: <RAID 1 (Mirror)> on aac0
aacd0: 34998MB (71677440 sectors)
GEOM: create disk aacd0 dp=0xc6c1940c
aacd1: <RAID 1 (Mirror)> on aac0
aacd1: 34998MB (71677440 sectors)
GEOM: create disk aacd1 dp=0xc6c1930c
GEOM: create disk da0 dp=0xc6a03450
GEOM: create disk da1 dp=0xc6a03050
da0 at ahc0 bus 0 target 0 lun 0
da0: <Promise 8 Disk RAID5 V0.0> Fixed Direct Access SCSI-4 device 
da0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled
da0: 1668429MB (3416944384 512 byte sectors: 255H 63S/T 212694C)
da1 at ahc0 bus 0 target 0 lun 1
da1: <Promise 6 Disk RAID5 V0.0> Fixed Direct Access SCSI-4 device 
da1: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled
da1: 1191735MB (2440674560 512 byte sectors: 255H 63S/T 151924C)
SMP: AP CPU #3 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
Mounting root from ufs:/dev/aacd0s1a
WARNING: /system was not properly dismounted
bge0: gigabit link up


--
William Colburn, "Sysprog" <wcolburn_at_nmt.edu>
Computer Center, New Mexico Institute of Mining and Technology
http://www.nmt.edu/tcc/     http://www.nmt.edu/~wcolburn