ISDN4BSD broken...

Hi all,

I just rebooted into the new cuurent-kernel and found, that i4b isn't 
working any more. Last working kernel was of Aug 11, around 1800 UTC.

Aug 14 18:19:46 current kernel: FreeBSD 5.2-CURRENT #0: \
	Sat Aug 14 17:43:56 CEST 2004
[...]
Aug 14 18:19:46 current kernel: ACPI link \_SB_.PCI0.LNKA \
	has invalid initial irq 9, ignoring
(this is a new message, which doesn't show up with my Aug 11 kernel)
[...]
Aug 14 18:19:46 current kernel: isic0: [GIANT-LOCKED]
Aug 14 18:19:46 current kernel: isic0 at port \
	0x580-0x59f,0x180-0x19f,0x980-0x99f,0xd80-0xd9f \
	irq 10 flags 0x3 on isa0
Aug 14 18:19:46 current kernel: isic0: passive stack unit 0
Aug 14 18:19:46 current kernel: isic0: Teles S0/16.3
[...]
Aug 14 18:19:46 current kernel: i4bisppp: \
	2 ISDN SyncPPP device(s) attached
Aug 14 18:19:46 current kernel: i4b: \
	ISDN call control device attached
Aug 14 18:19:46 current kernel: i4btrc: \
	1 ISDN trace device(s) attached
Aug 14 18:19:46 current kernel: i4brbch: \
	2 raw B channel access device(s) attached
Aug 14 18:19:46 current kernel: i4btel: \
	2 ISDN telephony interface device(s) attached
Aug 14 18:19:46 current kernel: i4bipr: \
	2 IP over raw HDLC ISDN device(s) attached (VJ header compression)
Aug 14 18:19:46 current kernel: i4bctl: \
	ISDN system control port attached

So far, the ISDN-Card is detected and attached as usual, but if I try to 
dial out, the following messages were recorded:

Aug 14 18:22:25 current kernel: i4b-L1 timer3_expired: \
	state = F4 Awaiting Signal
Aug 14 18:22:25 current kernel: i4b-L1 isic_recover: \
	HSCX B: ISTA = 0x0
Aug 14 18:22:25 current kernel: i4b-L1 isic_recover: \
	  ISAC: ISTA = 0x94
Aug 14 18:22:25 current kernel: i4b-L1 isic_recover: \
	  ISAC: CISQ = 0x1e
Aug 14 18:22:25 current kernel: i4b-L1 isic_recover: \
	HSCX B: IMASK = 0xff
Aug 14 18:22:25 current kernel: i4b-L1 isic_recover: \
	HSCX A: IMASK = 0xf8
Aug 14 18:22:25 current kernel: i4b-L1 isic_recover: \
	  ISAC: IMASK = 0x2a
Aug 14 18:22:25 current kernel: i4b-L2 i4b_T202_timeout: \
	unit 0, N202 = 3
Aug 14 18:22:25 current kernel: i4b-L1 isic_ph_data_req: \
	still in state F3!
Aug 14 18:22:27 current kernel: i4b-L3 T303_timeout: \
	SETUP not answered, cr = 15
Aug 14 18:22:27 current kernel: i4b-L3 next_l3state: \
	FSM illegal state, state = ST_OW - Out Wait EST, \
	event = EV_T303EXP - T303 timeout!
Aug 14 18:22:27 current kernel: i4b-L1 timer3_expired: \
	state = F4 Awaiting Signal
Aug 14 18:22:27 current kernel: i4b-L1 isic_recover: \
	HSCX B: ISTA = 0x0
Aug 14 18:22:27 current kernel: i4b-L1 isic_recover: \
	  ISAC: ISTA = 0x4
Aug 14 18:22:27 current kernel: i4b-L1 isic_recover: \
	  ISAC: CISQ = 0x32
Aug 14 18:22:27 current kernel: i4b-L1 isic_recover: \
	HSCX B: IMASK = 0xff
Aug 14 18:22:27 current kernel: i4b-L1 isic_recover: \
	HSCX A: IMASK = 0xf8
Aug 14 18:22:27 current kernel: i4b-L1 isic_recover: \
	  ISAC: IMASK = 0x2a

Any ideas? ACPI or IRQ-Routing related?
-- 
Ciao/BSD - Matthias

Matthias Schuendehuette	<msch [at] snafu.de>, Berlin (Germany)
PGP-Key at <pgp.mit.edu> and <wwwkeys.de.pgp.net> ID: 0xDDFB0A5F