Re: HPT374 Driver in -CURRENT

From: <freebsd_at_amarand.org>
Date: Fri, 6 Feb 2004 20:05:01 -0500 (EST)
On Fri, 6 Feb 2004, Jon Noack wrote:

> On 2/6/2004 6:38 AM, freebsd_at_amarand.org wrote:
> > When I boot 5.2(.1) from the ISOs, I am able to see -only- the ad4 and ad6
> > separate drive components of the RAID1 array, and not the actual RAID1
> > array itself (as ar*).  I'm using the standard sysconfig install, and
> > going into the Custom Expert mode, I am only given the option to select
> > ad4 and ad6 during the partitionable device selection, so I'm assuming (?)
> > that there's something else I need to do in the background or prior to
> > loading sysconfig in order to have sysconfig see the RAID1 array itself?
>
> The only other preparation I made before installation was to check again
> to make sure I enabled RAID mode and created an array in the bios of my
> HPT controller.  Also, you're only using RAID 1 and not RAID 5, correct?
>   Beyond that I don't really have any ideas.  Perhaps if you could post
> the kernel boot messages ("boot -v" would be better) someone else might
> have some insights.
>
> Just a random thought (and most likely completely wrong):
> Have you tried loading the installer in Safe Mode?  I only suggest this
> because I have a machine that has a very rocky relationship with apic...

Happiness is finding the right serial cable combination out of four
buckets of cables to make the serial console set-up work (thanks
FreeBSD Handbook!).  I've included the output of boot -v below.

To first answer your questions above for context:

Yes, I'm using RAID 1 (mirroring, confirmed in the BIOS) and the RAID
is enabled.  I can actually test this by booting back into the 5.1 CDs and
loading the module off of the floppy I have from the vendor for that
version.

I tried Safe Mode after your recommendation and that did not appear to
solve the problem.

I'm noticing, after having the ability now to view the bootup, that I'm
receiving the following error:

"ar: HighPoint check1 failed"

Any ideas anyone?

--Sean


OK boot -v
/boot/kernel/acpi.ko text=0x3f084 data=0x1724+0x114c
syms=[0x4+0x6af0+0x4+0x860f]
SMAP type=01 base=0000000000000000 len=00000000000a0000
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=01 base=0000000000100000 len=000000003fe74000
SMAP type=04 base=000000003ff74000 len=0000000000002000
SMAP type=03 base=000000003ff76000 len=0000000000021000
SMAP type=02 base=000000003ff97000 len=0000000000069000
SMAP type=02 base=00000000fed20000 len=0000000000070000
SMAP type=02 base=00000000fecf0000 len=0000000000001000
SMAP type=02 base=00000000fec00000 len=0000000000010000
SMAP type=02 base=00000000fee00000 len=0000000000010000
SMAP type=02 base=00000000ffb00000 len=0000000000500000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RC #0: Sat Jan 31 05:36:22 GMT 2004
    root_at_cypress.btc.adpatec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0e6d000.
Preloaded mfs_root "/boot/mfsroot" at 0xc0e6d2a0.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0e6d2e4.
Calibrating clock(s) ... i8254 clock: 1193152 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2793015432 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2793.02-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9

Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1073168384 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001029000 - 0x000000003ed4ffff, 1037201408 bytes (253223 pages)
avail memory = 1028935680 (981 MB)
Table 'FACP' at 0xfd17d
Table 'SSDT' at 0xfffc8a27
Table 'APIC' at 0xfd1f1
MADT: Found table at 0xfd1f1
MP Configuration Table version 1.4 found at 0xc00f0000
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 2: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 3: disabled
MADT: Found CPU APIC ID 3 ACPI ID 4: disabled
ACPI APIC Table: <DELL   PE400SC>
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xba63
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4  Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000
ioapic0: Changing APIC ID to 2
ioapic0: intpin 0 -> ExtINT (edge, activehi)
ioapic0: intpin 1 -> irq 1 (edge, activehi)
ioapic0: intpin 2 -> irq 2 (edge, activehi)
ioapic0: intpin 3 -> irq 3 (edge, activehi)
ioapic0: intpin 4 -> irq 4 (edge, activehi)
ioapic0: intpin 5 -> irq 5 (edge, activehi)
ioapic0: intpin 6 -> irq 6 (edge, activehi)
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
ioapic0: intpin 16 -> irq 16 (level, activelo)
ioapic0: intpin 17 -> irq 17 (level, activelo)
ioapic0: intpin 18 -> irq 18 (level, activelo)
ioapic0: intpin 19 -> irq 19 (level, activelo)
ioapic0: intpin 20 -> irq 20 (level, activelo)
ioapic0: intpin 21 -> irq 21 (level, activelo)
ioapic0: intpin 22 -> irq 22 (level, activelo)
ioapic0: intpin 23 -> irq 23 (level, activelo)
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
MADT: intr override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: active-hi
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   PE400SC> on motherboard
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80000090
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=25788086)
pcibios: BIOS version 2.10
Using $PIR table, 8 entries at 0xc00feae0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0   31    A   0x62  3 4 5 6 7 9 10 11 14 15
embedded    0   31    B   0x61  3 4 5 6 7 9 10 11 14 15
embedded    0   29    A   0x60  3 4 5 6 7 9 10 11 14 15
embedded    0   29    B   0x63  3 4 5 6 7 9 10 11 14 15
embedded    0   29    C   0x62  3 4 5 6 7 9 10 11 14 15
embedded    0   29    D   0x6b  3 4 5 6 7 9 10 11 14 15
embedded    1    0    A   0x60  3 4 5 6 7 9 10 11 14 15
embedded    1    0    B   0x61  3 4 5 6 7 9 10 11 14 15
embedded    2   12    A   0x62  3 4 5 6 7 9 10 11 14 15
slot 1      2    0    A   0x69  3 4 5 6 7 9 10 11 14 15
slot 1      2    0    B   0x6a  3 4 5 6 7 9 10 11 14 15
slot 1      2    0    C   0x6b  3 4 5 6 7 9 10 11 14 15
slot 1      2    0    D   0x68  3 4 5 6 7 9 10 11 14 15
slot 2      2    1    A   0x6a  3 4 5 6 7 9 10 11 14 15
slot 2      2    1    B   0x69  3 4 5 6 7 9 10 11 14 15
slot 2      2    1    C   0x68  3 4 5 6 7 9 10 11 14 15
slot 2      2    1    D   0x6b  3 4 5 6 7 9 10 11 14 15
slot 3      2    2    A   0x61  3 4 5 6 7 9 10 11 14 15
slot 3      2    2    B   0x62  3 4 5 6 7 9 10 11 14 15
slot 3      2    2    C   0x63  3 4 5 6 7 9 10 11 14 15
slot 3      2    2    D   0x60  3 4 5 6 7 9 10 11 14 15
slot 4      2    3    A   0x63  3 4 5 6 7 9 10 11 14 15
slot 4      2    3    B   0x62  3 4 5 6 7 9 10 11 14 15
slot 4      2    3    C   0x69  3 4 5 6 7 9 10 11 14 15
slot 4      2    3    D   0x6a  3 4 5 6 7 9 10 11 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 29 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 29 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 29 func 2
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 29 func 3
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 3, width = 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
        map[10]: type 3, range 32, base f0000000, size 27, enabled
found-> vendor=0x8086, dev=0x2578, revid=0x02
        bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2579, revid=0x02
        bus=0, slot=1, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 0000ff80, size  5, enabled
pcib0: matched entry for 0.29.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24d2, revid=0x02
        bus=0, slot=29, func=0
        class=0c-03-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=16
        map[20]: type 4, range 32, base 0000ff60, size  5, enabled
pcib0: matched entry for 0.29.INTB (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x24d4, revid=0x02
        bus=0, slot=29, func=1
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=19
        map[20]: type 4, range 32, base 0000ff40, size  5, enabled
pcib0: matched entry for 0.29.INTC (source )
pcib0: device is hardwired to IRQ 18
found-> vendor=0x8086, dev=0x24d7, revid=0x02
        bus=0, slot=29, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=18
        map[20]: type 4, range 32, base 0000ff20, size  5, enabled
pcib0: matched entry for 0.29.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24de, revid=0x02
        bus=0, slot=29, func=3
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=16
        map[10]: type 1, range 32, base ffa80800, size 10, enabled
pcib0: matched entry for 0.29.INTD (source )
pcib0: device is hardwired to IRQ 23
found-> vendor=0x8086, dev=0x24dd, revid=0x02
        bus=0, slot=29, func=7
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=23
        powerspec 2  supports D0 D3  current D0
found-> vendor=0x8086, dev=0x244e, revid=0xc2
        bus=0, slot=30, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24d0, revid=0x02
        bus=0, slot=31, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[10]: type 4, range 32, base 000001f0, size  3, enabled
        map[14]: type 4, range 32, base 000003f4, size  2, enabled
        map[18]: type 4, range 32, base 00000170, size  3, enabled
        map[1c]: type 4, range 32, base 00000374, size  2, enabled
        map[20]: type 4, range 32, base 0000ffa0, size  4, enabled
        map[24]: type 1, range 32, base febffc00, size 10, enabled
pcib0: matched entry for 0.31.INTA (source )
pcib0: device is hardwired to IRQ 18
found-> vendor=0x8086, dev=0x24db, revid=0x02
        bus=0, slot=31, func=1
        class=01-01-8a, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=18
        map[10]: type 4, range 32, base 0000fe00, size  3, enabled
        map[14]: type 4, range 32, base 0000fe10, size  2, enabled
        map[18]: type 4, range 32, base 0000fe20, size  3, enabled
        map[1c]: type 4, range 32, base 0000fe30, size  2, enabled
        map[20]: type 4, range 32, base 0000fea0, size  4, enabled
pcib0: matched entry for 0.31.INTA (source )
pcib0: device is hardwired to IRQ 18
found-> vendor=0x8086, dev=0x24d1, revid=0x02
        bus=0, slot=31, func=2
        class=01-01-8f, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x02a0, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=18
        map[20]: type 4, range 32, base 0000eda0, size  5, enabled
pcib0: matched entry for 0.31.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x24d3, revid=0x02
        bus=0, slot=31, func=3
        class=0c-05-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=17
        map[10]: type 4, range 32, base 0000ee00, size  8, enabled
        map[14]: type 4, range 32, base 0000edc0, size  6, enabled
        map[18]: type 1, range 32, base febffa00, size  9, enabled
        map[1c]: type 1, range 32, base febff900, size  8, enabled
pcib0: matched entry for 0.31.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x24d5, revid=0x02
        bus=0, slot=31, func=5
        class=04-01-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=17
        powerspec 2  supports D0 D3  current D0
agp0: <Intel 82875P host to AGP bridge> mem 0xf0000000-0xf7ffffff at
device 0.0
on pci0
agp0: allocating GATT for aperture of size 128M
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xf000-0xfff
pcib1:   memory decode     0xfff00000-0xfffff
pcib1:   prefetched decode 0xfff00000-0xfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xff80-0xff9f irq
16 at
device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xff60-0xff7f irq
19 at
device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xff40-0xff5f irq
18 at
device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xff20-0xff3f irq
16 at
device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xd000-0xdfff
pcib2:   memory decode     0xfd000000-0xfeafffff
pcib2:   prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
        map[10]: type 1, range 32, base fd000000, size 24, enabled
        map[14]: type 4, range 32, base 0000dc00, size  8, enabled
        map[18]: type 1, range 32, base fe99d000, size 12, enabled
pcib2: matched entry for 2.0.INTA (source )
pcib2: device is hardwired to IRQ 21
found-> vendor=0x1002, dev=0x4752, revid=0x27
        bus=2, slot=0, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=21
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 4, range 32, base 0000daa0, size  3, enabled
        map[14]: type 4, range 32, base 0000da90, size  2, enabled
        map[18]: type 4, range 32, base 0000daa8, size  3, enabled
        map[1c]: type 4, range 32, base 0000da94, size  2, enabled
        map[20]: type 4, range 32, base 0000dd00, size  8, enabled
pcib2: matched entry for 2.1.INTA (source )
pcib2: device is hardwired to IRQ 22
found-> vendor=0x1103, dev=0x0008, revid=0x07
        bus=2, slot=1, func=0
        class=01-04-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0105, statreg=0x0230, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000
ns)
        intpin=a, irq=22
        powerspec 2  supports D0 D3  current D0
        map[10]: type 4, range 32, base 0000dab0, size  3, enabled
        map[14]: type 4, range 32, base 0000da98, size  2, enabled
        map[18]: type 4, range 32, base 0000dab8, size  3, enabled
        map[1c]: type 4, range 32, base 0000da9c, size  2, enabled
        map[20]: type 4, range 32, base 0000de00, size  8, enabled
pcib2: matched entry for 2.1.INTA (source )
pcib2: device is hardwired to IRQ 22
found-> vendor=0x1103, dev=0x0008, revid=0x07
        bus=2, slot=1, func=1
        class=01-04-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0105, statreg=0x0230, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000
ns)
        intpin=a, irq=22
        powerspec 2  supports D0 D3  current D0
        map[10]: type 1, range 32, base fe99e000, size 12, enabled
        map[14]: type 4, range 32, base 0000dac0, size  6, enabled
        map[18]: type 1, range 32, base fe9a0000, size 17, enabled
pcib2: matched entry for 2.2.INTA (source )
pcib2: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x1229, revid=0x0c
        bus=2, slot=2, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000
ns)
        intpin=a, irq=17
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base fe99f000, size 12, enabled
        map[14]: type 4, range 32, base 0000db00, size  6, enabled
        map[18]: type 1, range 32, base fe9c0000, size 17, enabled
pcib2: matched entry for 2.3.INTA (source )
pcib2: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x1229, revid=0x0c
        bus=2, slot=3, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000
ns)
        intpin=a, irq=19
        powerspec 2  supports D0 D1 D2 D3  current D0
pci2: <display, VGA> at device 0.0 (no driver attached)
atapci0: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port
0xdd00-0xddff,0xda94-0xda97,0xdaa8-0xdaaf,0xda90-0xda93,0xdaa0-0xdaa7 irq
22 at device 1.0 on
pci2
pcib2: device atapci0 requested decoded I/O range 0xdd00-0xddff
atapci0: [MPSAFE]
pcib2: device atapci0 requested decoded I/O range 0xdaa0-0xdaa7
pcib2: device atapci0 requested decoded I/O range 0xda90-0xda93
pcib2: device atapci0 requested decoded I/O range 0xda92-0xda92
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: at 0xdaa0 on atapci0
ata2: [MPSAFE]
pcib2: device atapci0 requested decoded I/O range 0xdaa8-0xdaaf
pcib2: device atapci0 requested decoded I/O range 0xda94-0xda97
pcib2: device atapci0 requested decoded I/O range 0xda96-0xda96
ata3: reset tp1 mask=03 ostat0=50 ostat1=00
ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata3-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata3: at 0xdaa8 on atapci0
ata3: [MPSAFE]
atapci1: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port
0xde00-0xdeff,0xda9c-0xda9f,0xdab8-0xdabf,0xda98-0xda9b,0xdab0-0xdab7 irq
22 at device 1.1 on
pci2
pcib2: device atapci1 requested decoded I/O range 0xde00-0xdeff
atapci1: [MPSAFE]
pcib2: device atapci1 requested decoded I/O range 0xdab0-0xdab7
pcib2: device atapci1 requested decoded I/O range 0xda98-0xda9b
pcib2: device atapci1 requested decoded I/O range 0xda9a-0xda9a
ata4: reset tp1 mask=03 ostat0=20 ostat1=30
ata4-master: stat=0x20 err=0x20 lsb=0x20 msb=0x20
ata4-slave:  stat=0x30 err=0x30 lsb=0x30 msb=0x30
ata4: reset tp2 mask=03 stat0=20 stat1=30 devices=0x0
ata4: at 0xdab0 on atapci1
ata4: [MPSAFE]
pcib2: device atapci1 requested decoded I/O range 0xdab8-0xdabf
pcib2: device atapci1 requested decoded I/O range 0xda9c-0xda9f
pcib2: device atapci1 requested decoded I/O range 0xda9e-0xda9e
ata5: reset tp1 mask=03 ostat0=20 ostat1=30
ata5-master: stat=0x20 err=0x20 lsb=0x20 msb=0x20
ata5-slave:  stat=0x30 err=0x30 lsb=0x30 msb=0x30
ata5: reset tp2 mask=03 stat0=20 stat1=30 devices=0x0
ata5: at 0xdab8 on atapci1
ata5: [MPSAFE]
fxp0: <Intel 82550 Pro/100 Ethernet> port 0xdac0-0xdaff mem
0xfe9a0000-0xfe9bffff,0xfe99e000-0xfe99efff irq 17 at device 2.0 on pci2
pcib2: device fxp0 requested decoded memory range 0xfe99e000-0xfe99efff
fxp0: using memory space register mapping
fxp0: Ethernet address 00:02:b3:d6:f3:26
fxp0: PCI IDs: 8086 1229 8086 0040 000c
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp1: <Intel 82550 Pro/100 Ethernet> port 0xdb00-0xdb3f mem
0xfe9c0000-0xfe9dffff,0xfe99f000-0xfe99ffff irq 19 at device 3.0 on pci2
pcib2: device fxp1 requested decoded memory range 0xfe99f000-0xfe99ffff
fxp1: using memory space register mapping
fxp1: Ethernet address 00:02:b3:d6:f3:78
fxp1: PCI IDs: 8086 1229 8086 0040 000c
fxp1: Dynamic Standby mode is disabled
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: bpf attached
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci2: <Intel ICH5 UDMA100 controller> port
0xffa0-0xffaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem
0xfebffc00-0xfebfffff irq 18 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci2
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=01
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci2
ata1: [MPSAFE]
atapci3: <Intel ICH5 SATA150 controller> port
0xfea0-0xfeaf,0xfe30-0xfe33,0xfe20-0xfe27,0xfe10-0xfe13,0xfe00-0xfe07 irq
18 at device 31.2 on pci0
atapci3: [MPSAFE]
ata6: at 0xfe00 on atapci3
ata6: [MPSAFE]
ata7: at 0xfe20 on atapci3
ata7: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: unable to allocate IRQ
psmcpnp0 irq 12 on acpi0
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 03 28
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 90 03 3c
psm: data 08 00 00
psm: data 08 00 00
psm: status 00 03 28
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
sio0: irq maps: 0x8001 0x8011 0x8001 0x8001
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1: irq maps: 0x8001 0x8009 0x8001 0x8001
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem
0xd0800-0xd3fff,0xcf000-0xd07ff,0xcd800-0xcefff,0xcc000-0xcd7ff,0xc8000-0xcbfff,0xc0000-0xc7fff
on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 2793015432 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc09e13dc
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
GEOM: Configure md0a, start 0 length 4423680 end 4423679
GEOM: Configure md0c, start 0 length 4423680 end 4423679
ata1-master: setting PIO4 on Intel ICH5 chip
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
acd0: <HL-DT-ST CD-RW/DVD-ROM GCC-4480B/C104> CDRW drive at ata1 as master
acd0: read 8251KB/s (8251KB/s) write 5501KB/s (5501KB/s), 2048KB buffer,
PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm data disc
ata2-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
ata2-master: setting PIO4 on HighPoint chip
ata2-master: setting UDMA133 on HighPoint chip
GEOM: create disk ad4 dp=0xc6dca660
ad4: <Maxtor 6Y200P0/YAR41BW0> ATA-7 disk at ata2-master
ad4: 194481MB (398297088 sectors), 395136 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA133
ar: HighPoint check1 failed
ata3-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
ata3-master: setting PIO4 on HighPoint chip
ata3-master: setting UDMA133 on HighPoint chip
GEOM: create disk ad6 dp=0xc6dca560
ad6: <Maxtor 6Y200P0/YAR41BW0> ATA-7 disk at ata3-master
ad6: 194481MB (398297088 sectors), 395136 C, 16 H, 63 S, 512 B
ad6: 16 secs/int, 1 depth queue, UDMA133
ar: HighPoint check1 failed
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00050014 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 3 (IRQ 3) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 6 (IRQ 6) to cluster 0
ioapic0: routing intpin 7 (IRQ 7) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 12 (IRQ 12) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
ioapic0: routing intpin 22 (IRQ 22) to cluster 0
GEOM: new disk ad4
GEOM: new disk ad6
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:124985637
[1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:124985700
l:149998905
[2] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:274984605
l:106398495
[3] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:381383100
l:16771860
GEOM: Configure ad4s1, start 32256 length 63992646144 end 63992678399
GEOM: Configure ad4s2, start 63992678400 length 76799439360 end
140792117759
GEOM: Configure ad4s3, start 140792117760 length 54476029440 end
195268147199
GEOM: Configure ad4s4, start 195268147200 length 8587192320 end
203855339519
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:124985637
[1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:124985700
l:149998905
[2] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:274984605
l:106398495
[3] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:381383100
l:16771860
GEOM: Configure ad6s1, start 32256 length 63992646144 end 63992678399
GEOM: Configure ad6s2, start 63992678400 length 76799439360 end
140792117759
GEOM: Configure ad6s3, start 140792117760 length 54476029440 end
195268147199
GEOM: Configure ad6s4, start 195268147200 length 8587192320 end
203855339519
GEOM: Configure ad4s1a, start 0 length 63992646144 end 63992646143
GEOM: Configure ad4s1c, start 0 length 63992646144 end 63992646143
GEOM: Configure ad4s2c, start 0 length 76799439360 end 76799439359
GEOM: Configure ad4s2d, start 0 length 76799439360 end 76799439359
GEOM: Configure ad4s3c, start 0 length 54476029440 end 54476029439
GEOM: Configure ad4s3d, start 0 length 54476029440 end 54476029439
GEOM: Configure ad4s4b, start 0 length 8587192320 end 8587192319
GEOM: Configure ad4s4c, start 0 length 8587192320 end 8587192319
GEOM: Configure ad6s1a, start 0 length 63992646144 end 63992646143
GEOM: Configure ad6s1c, start 0 length 63992646144 end 63992646143
GEOM: Configure ad6s2c, start 0 length 76799439360 end 76799439359
GEOM: Configure ad6s2d, start 0 length 76799439360 end 76799439359
GEOM: Configure ad6s3c, start 0 length 54476029440 end 54476029439
GEOM: Configure ad6s3d, start 0 length 54476029440 end 54476029439
GEOM: Configure ad6s4b, start 0 length 8587192320 end 8587192319
GEOM: Configure ad6s4c, start 0 length 8587192320 end 8587192319
Mounting root from ufs:/dev/md0
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
/stand/sysinstall running as init on serial console
Received on Fri Feb 06 2004 - 16:05:28 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:42 UTC