I cannot use Dell USB cdrom with 5.2-RELEASE. The same drive works without any problems on 4.9. Any clues? Boot log attached. /Yuri Regents of the University of California. All rights reserved. FreeBSD 5.2-RELEASE #2: Tue Jan 13 11:44:10 CET 2004 root_at_macinino.astro.uu.se:/usr/obj/usr/src/sys/MACININO Preloaded elf kernel "/boot/kernel/kernel" at 0xc083d000. Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc083d228. Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc083d2d4. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc083d380. Calibrating clock(s) ... i8254 clock: 1193190 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1398816056 Hz CPU: Intel(R) Pentium(R) M processor 1400MHz (1398.82-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x695 Stepping = 5 Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT, CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE> real memory = 1072340992 (1022 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c26000 - 0x000000003ec89fff, 1040596992 bytes (254052 pages) avail memory = 1032208384 (984 MB) bios32: Found BIOS32 Service Directory header at 0xc00ffe80 bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xc97e pnpbios: Found PnP BIOS data at 0xc00fe2d0 pnpbios: Entry = f0000:e2f4 Rev = 1.0 pnpbios: Event flag at 4b4 Other BIOS signatures found: wlan: <802.11 Link Layer> null: <null device, zero device> mem: <memory & I/O> Pentium Pro MTRR support enabled random: <entropy source> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL CPi R > on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x8000eac4 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=35808086) pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00fc5a0 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 B 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 C 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 D 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 0 2 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 1 0 A 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 1 1 A 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 1 1 B 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 1 3 A 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 1 3 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 8 0 A 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 8 0 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 8 1 A 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 8 1 B 0x63 3 4 5 6 7 9 10 11 12 14 15 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 acpi_acad0: <AC Adapter> on acpi0 acpi_cmbat0: <Control Method Battery> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 - ---- initial configuration ------------------------ \\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.31.0 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.31.1 \\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.31.2 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.31.3 \\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.29.0 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.29.1 \\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.29.2 \\_SB_.PCI0.LNKH irq 11: [ 3 4 5 6 7 9 10 11 12 14 15] low,level,sharable 0.29.3 \\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.2.0 - ---- before setting priority for links ------------ - ---- before fixup boot-disabled links ------------- - ---- after fixup boot-disabled links -------------- - ---- arbitrated configuration --------------------- \\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.31.0 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.31.1 \\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.31.2 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.31.3 \\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.29.0 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.29.1 \\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.29.2 \\_SB_.PCI0.LNKH irq 11: [ 3 4 5 6 7 9 10 11 12 14 15] low,level,sharable 0.29.3 \\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.2.0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base 00000000, size 0, enabled found-> vendor=0x8086, dev=0x3580, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3584, revid=0x02 bus=0, slot=0, func=1 class=08-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3585, revid=0x02 bus=0, slot=0, func=3 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 3, range 32, base f0000000, size 27, enabled map[14]: type 1, range 32, base faf80000, size 19, enabled map[18]: type 4, range 32, base 0000c000, size 3, enabled pcib0: matched entry for 0.2.INTA (source \\_SB_.PCI0.LNKA) pcib0: slot 2 INTA is routed to irq 11 found-> vendor=0x8086, dev=0x3582, revid=0x02 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 1 supports D0 D1 D3 current D0 map[10]: type 3, range 32, base e8000000, size 27, enabled map[14]: type 1, range 32, base faf00000, size 19, enabled found-> vendor=0x8086, dev=0x3582, revid=0x02 bus=0, slot=2, func=1 class=03-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 1 supports D0 D1 D3 current D0 map[20]: type 4, range 32, base 0000bf80, size 5, enabled pcib0: matched entry for 0.29.INTA (source \\_SB_.PCI0.LNKA) pcib0: slot 29 INTA is routed to irq 11 found-> vendor=0x8086, dev=0x24c2, revid=0x01 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[20]: type 4, range 32, base 0000bf40, size 5, enabled pcib0: matched entry for 0.29.INTB (source \\_SB_.PCI0.LNKD) pcib0: slot 29 INTB is routed to irq 11 found-> vendor=0x8086, dev=0x24c4, revid=0x01 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type 4, range 32, base 0000bf20, size 5, enabled pcib0: matched entry for 0.29.INTC (source \\_SB_.PCI0.LNKC) pcib0: slot 29 INTC is routed to irq 11 found-> vendor=0x8086, dev=0x24c7, revid=0x01 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=11 map[10]: type 1, range 32, base faeffc00, size 10, enabled pcib0: matched entry for 0.29.INTD (source \\_SB_.PCI0.LNKH) pcib0: slot 29 INTD is routed to irq 11 found-> vendor=0x8086, dev=0x24cd, revid=0x01 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=11 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x2448, revid=0x81 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x8080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24cc, revid=0x01 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 000001f0, size 3, enabled map[14]: type 4, range 32, base 000003f4, size 2, enabled map[18]: type 4, range 32, base 00000170, size 3, enabled map[1c]: type 4, range 32, base 00000374, size 2, enabled map[20]: type 4, range 32, base 0000bfa0, size 4, enabled found-> vendor=0x8086, dev=0x24ca, revid=0x01 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[10]: type 4, range 32, base 0000d800, size 8, enabled map[14]: type 4, range 32, base 0000dc40, size 6, enabled map[18]: type 1, range 32, base faeff800, size 9, enabled map[1c]: type 1, range 32, base faeff400, size 8, enabled pcib0: matched entry for 0.31.INTB (source \\_SB_.PCI0.LNKB) pcib0: slot 31 INTB is routed to irq 11 found-> vendor=0x8086, dev=0x24c5, revid=0x01 bus=0, slot=31, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000d400, size 8, enabled map[14]: type 4, range 32, base 0000d080, size 7, enabled pcib0: matched entry for 0.31.INTB (source \\_SB_.PCI0.LNKB) pcib0: slot 31 INTB is routed to irq 11 found-> vendor=0x8086, dev=0x24c6, revid=0x01 bus=0, slot=31, func=6 class=07-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 pci0: <base peripheral> at device 0.1 (no driver attached) pci0: <base peripheral> at device 0.3 (no driver attached) agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0xc000-0xc007 mem 0xfaf80000-0xfaffffff,0xf0000000-0xf7ffffff irq 11 at device 2.0 on pci0 agp0: detected 892k stolen memory agp0: aperture size is 128M pci0: <display> at device 2.1 (no driver attached) uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0 usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at device 29.1 on pci0 usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered umass0: Dell USB Drive A01, rev 2.00/1.04, addr 2 umass0: Get Max Lun not supported (STALLED) umass0:0:0:-1: Attached to scbus0 uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at device 29.2 on pci0 usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xe000-0xefff pcib1: memory decode 0xfc000000-0xfdffffff pcib1: prefetched decode 0xfff00000-0xfffff - ---- initial configuration ------------------------ \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 1.1.0 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 1.1.1 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 1.3.0 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 1.3.1 \\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 1.0.0 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 1.8.0 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 1.8.1 - ---- before setting priority for links ------------ - ---- before fixup boot-disabled links ------------- - ---- after fixup boot-disabled links -------------- - ---- arbitrated configuration --------------------- \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 1.1.0 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 1.1.1 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 1.3.0 \\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 1.3.1 \\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 1.0.0 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 1.8.0 \\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 1.8.1 pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 64, base fcff0000, size 16, enabled pcib1: matched entry for 1.0.INTA (source \\_SB_.PCI0.LNKC) pcib1: slot 0 INTA is routed to irq 11 found-> vendor=0x14e4, dev=0x165d, revid=0x01 bus=1, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0116, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit found-> vendor=0x104c, dev=0xac47, revid=0x01 bus=1, slot=1, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 pcib1: matched entry for 1.1.INTA (source \\_SB_.PCI0.LNKD) pcib1: slot 1 INTA is routed to irq 11 found-> vendor=0x104c, dev=0xac4a, revid=0x01 bus=1, slot=1, func=1 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0107, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fcfef800, size 11, enabled map[14]: type 1, range 32, base fcfe8000, size 14, enabled pcib1: matched entry for 1.1.INTA (source \\_SB_.PCI0.LNKD) pcib1: slot 1 INTA is routed to irq 11 found-> vendor=0x104c, dev=0x802b, revid=0x00 bus=1, slot=1, func=2 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0116, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 0000ecf8, size 3, enabled found-> vendor=0x104c, dev=0x8204, revid=0x00 bus=1, slot=1, func=3 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0101, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base fcfec000, size 13, enabled pcib1: matched entry for 1.3.INTA (source \\_SB_.PCI0.LNKB) pcib1: slot 3 INTA is routed to irq 11 found-> vendor=0x14e4, dev=0x4320, revid=0x02 bus=1, slot=3, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 bge0: <Broadcom BCM5705M Gigabit Ethernet, ASIC rev. 0x3001> mem 0xfcff0000-0xfcffffff irq 11 at device 0.0 on pci1 pcib1: device bge0 requested decoded memory range 0xfcff0000-0xfcffffff bge0: Ethernet address: 00:0d:56:6d:42:2f miibus0: <MII bus> on bge0 brgphy0: <BCM5705 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: bpf attached cbb0: <PCI-CardBus Bridge> at device 1.0 on pci1 pcib1: device cbb0 requested decoded memory range 0xfc000000-0xfdffffff cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 pcib1: matched entry for 1.1.INTA (source \\_SB_.PCI0.LNKD) pcib1: slot 1 INTA is routed to irq 11 cbb0: [MPSAFE] cbb0: PCI Configuration space: 0x00: 0xac47104c 0x02100007 0x06070001 0x00822008 0x10: 0xfc000000 0x020000a0 0x20000000 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 0x40: 0x01391028 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x38405061 0x00000019 0x001f0000 0x012c1202 0x90: 0x606482c0 0x00000000 0x00000000 0x00000000 0xa0: 0xfe320001 0x00c00000 0x00000000 0x00000000 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 cbb1: <PCI-CardBus Bridge> irq 11 at device 1.1 on pci1 pcib1: device cbb1 requested decoded memory range 0xfc000000-0xfdffffff cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 cbb1: [MPSAFE] cbb1: PCI Configuration space: 0x00: 0xac4a104c 0x02100107 0x06070001 0x00822008 0x10: 0xfc001000 0x020000a0 0x20000000 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 0x40: 0x01391028 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x38445161 0x00000019 0x001f0000 0x012c1202 0x90: 0x606480c0 0x00000000 0x00000000 0x00000000 0xa0: 0xfe320001 0x00c00000 0x00000000 0x00000000 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 fwohci0: vendor=104c, dev=802b fwohci0: <1394 Open Host Controller Interface> mem 0xfcfe8000-0xfcfebfff,0xfcfef800-0xfcfeffff irq 11 at device 1.2 on pci1 fwohci0: latency timer 32 -> 32. fwohci0: cache size 8 -> 8. pcib1: device fwohci0 requested decoded memory range 0xfcfef800-0xfcfeffff fwohci0: OHCI version 1.10 (ROM=0) fwohci0: No. of Isochronous channel is 4. fwohci0: EUI64 32:4f:c0:00:0c:7f:70:10 fwohci0: resetting OHCI...done (loop=0) fwohci0: fwphy_rddata: 0x2 loop=0, retry=0 fwohci0: fwphy_rddata: 0x3 loop=0, retry=0 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: fwphy_rddata: 0x5 loop=0, retry=0 fwohci0: Enable 1394a Enhancements fwohci0: fwphy_rddata: 0x5 loop=0, retry=0 fwohci0: fwphy_rddata: 0x2 loop=0, retry=0 fwohci0: fwphy_rddata: 0x4 loop=0, retry=0 fwohci0: fwphy_rddata: 0x4 loop=0, retry=0 fwohci0: fwphy_rddata: 0x4 loop=0, retry=0 fwohci0: Link S400, max_rec 2048 bytes. fwohci0: BUS_OPT 0xa002 -> 0xf800a002 fwohci0: fwohci_set_intr: 1 firewire0: <IEEE1394(FireWire) bus> on fwohci0 sbp0: <SBP-2/SCSI over FireWire> on firewire0 sbp_attach (cold=1) fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 32:4f:c0:7f:70:10 fwe0: bpf attached fwohci0: Initiate bus reset fwohci0: fwphy_rddata: 0x1 loop=0, retry=0 fwohci0: fwphy_rddata: 0x1 loop=0, retry=0 fwohci0: BUS reset sbp_post_busreset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) fwohci0: fw_set_bus_manager: 0->0 (loop=0) firewire0: bus manager 0 (me) send phy_config root_node=-1 gap_count=5 fwohci0: maxdesc: 2 fwohci0: start AT DMA status=0 pci1: <base peripheral> at device 1.3 (no driver attached) pci1: <network> at device 3.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x170-0 x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=00 ostat1=00 ata1-master: stat=0x01 err=0x01 lsb=0x01 msb=0x01 ata1-slave: stat=0x01 err=0x01 lsb=0x01 msb=0x01 ata1: reset tp2 mask=03 stat0=01 stat1=01 devices=0x0 ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pcm0: <Intel ICH4 (82801DB)> port 0xdc40-0xdc7f,0xd800-0xd8ff mem 0xfaeff400-0xfaeff4ff,0xfaeff800-0xfaeff9ff irq 11 at device 31.5 on pci0 pcm0: <SigmaTel STAC9750/51 AC97 Codec (id = 0x83847650)> pcm0: Codec features headphone, 20 bit DAC, 20 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement pcm0: Primary codec extended features variable rate PCM, reserved 1, AMAP, reserved 4 pcm0: sndbuf_setmap 2e7000, 4000; 0xe9f66000 -> 2e7000 pcm0: sndbuf_setmap 2eb000, 4000; 0xe9f6a000 -> 2eb000 pci0: <simple comms> at device 31.6 (no driver attached) unknown: not probed (disabled) psmcpnp0 irq 12 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model GlidePoint, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 sio0: irq maps: 0x801 0x811 0x801 0x801 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A unknown: not probed (disabled) ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xcf000-0xcf7ff,0xce800-0xcefff,0x ce000-0xce7ff,0xcd800-0xcdfff,0xc0000-0xcd7ff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 fdc0 failed to probe at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x801 0x801 0x801 0x801 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 1398816056 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached Current DB 0 ch = 0 Current OP KEY INT BR len Addr Depend Stat: Cnt 3e0fb000 OUTL ST2 ALL ALL 12 00000000 3e0fb080 8411:000e RUN,ACTIVE, ack complete(11) 0x000000e0 0x00450000 0xffbaffff 0x00000000 acpi_cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% acpi_acad0: acline initialization start system power profile changed to 'economy' acpi_cpu0: set speed to 50.0% acpi_acad0: Off Line acpi_cmbat0: battery initialization start acpi_cmbat0: battery initialization done, tried 1 times ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: setting PIO4 on Intel ICH4 chip ata0-master: setting UDMA100 on Intel ICH4 chip GEOM: create disk ad0 dp=0xc6ae2a60 ad0: <IC25N060ATMR04-0/MO3OAD0A> ATA-6 disk at ata0-master ad0: 57231MB (117210240 sectors), 116280 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 pcm0: measured ac97 link rate at 48015 Hz, will use 48000 Hz GEOM: new disk ad0 bus_explore done sbp_post_explore (sbp_cold=2) [0] f:00 typ:222 s(CHS):0/1/1 e(CHS):5/254/63 s:63 l:96327 [1] f:00 typ:7 s(CHS):6/0/1 e(CHS):1023/254/63 s:96390 l:30716280 [2] f:80 typ:165 s(CHS):1023/0/1 e(CHS):1023/254/63 s:30812670 l:86397570 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 49319424 end 49351679 GEOM: Configure ad0s2, start 49351680 length 15726735360 end 15776087039 GEOM: Configure ad0s3, start 15776087040 length 44235555840 end 60011642879 GEOM: Configure ad0s3a, start 0 length 268435456 end 268435455 GEOM: Configure ad0s3b, start 268435456 length 2147483648 end 2415919103 GEOM: Configure ad0s3c, start 0 length 44235555840 end 44235555839 GEOM: Configure ad0s3e, start 2415919104 length 268435456 end 2684354559 GEOM: Configure ad0s3f, start 2684354560 length 268435456 end 2952790015 GEOM: Configure ad0s3g, start 2952790016 length 41282765824 end 44235555839 umass0: Phase Error, residue = 0 (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (probe0:umass-sim0:0:0:0): Retrying Command umass0: Phase Error, residue = 0 (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (probe0:umass-sim0:0:0:0): Retrying Command umass0: Phase Error, residue = 0 (probe3:sbp0:0:2:0): error 22 (probe3:sbp0:0:2:0): Unretryable Error (probe4:sbp0:0:3:0): error 22 (probe4:sbp0:0:3:0): Unretryable Error (probe5:sbp0:0:4:0): error 22 (probe5:sbp0:0:4:0): Unretryable Error (probe6:sbp0:0:5:0): error 22 (probe6:sbp0:0:5:0): Unretryable Error (probe7:sbp0:0:6:0): error 22 (probe7:sbp0:0:6:0): Unretryable Error (probe1:sbp0:0:0:0): error 22 (probe1:sbp0:0:0:0): Unretryable Error (probe2:sbp0:0:1:0): error 22 (probe2:sbp0:0:1:0): Unretryable Error (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (probe0:umass-sim0:0:0:0): Retrying Command umass0: Phase Error, residue = 0 (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (probe0:umass-sim0:0:0:0): Retrying Command umass0: Phase Error, residue = 0 (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (probe0:umass-sim0:0:0:0): error 5 (probe0:umass-sim0:0:0:0): Retries Exausted Mounting root from ufs:/dev/ad0s3a start_init: trying /sbin/init acpi_acad0: acline initialization done, tried 7 times bge0 Linux ELF exec handler installed -- Yuri Khotyaintsev, PhD Swedish Institute of Space Physics, http://www.cluster.irfu.se/yuri Uppsala Division (IRF-U), http://ovt.irfu.seReceived on Tue Jan 13 2004 - 02:33:16 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:37 UTC