Re: ACPI on Fujitsu P2120

From: Erich Dollansky <oceanare_at_pacific.net.sg>
Date: Sat, 24 Jan 2004 01:46:05 +0800
Hi,

I managed to get debugging running.

I will look later into this. It got a bit late here.

Erich

PS

Here is "dmesg" after the first boot.

Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 
1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.2-RELEASE #12: Sat Jan 24 00:59:15 SGT 2004
     root_at_CRUSOE:/usr/src/sys/i386/compile/CRUSOE
Preloaded elf kernel "/boot/kernel/kernel" at 0xc088b000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc088b244.
Calibrating clock(s) ... i8254 clock: 1193184 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 666313999 Hz
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 (666.31-MHz 
586-class CPU)
   Origin = "GenuineTMx86"  Id = 0x543
   Processor revision 1.4.1.0
   Code Morphing Software revision 4.3.2-9-566
   20030108 13:03 official release 28.0.3-4.3.2#1
   LongRun mode: 2  <933MHz 1350mV 100%>
real memory  = 385744896 (367 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c26000 - 0x0000000016941fff, 366067712 bytes (89372 pages)
avail memory = 364998656 (348 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f6f40
bios32: Entry = 0xfd780 (c00fd780)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xfd780+0x11e
pnpbios: Found PnP BIOS data at 0xc00f6f90
pnpbios: Entry = f0000:953b  Rev = 1.0
Other BIOS signatures found:
netsmb_dev: loaded
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
VESA: information block
56 45 53 41 00 02 00 01 00 01 01 00 00 00 22 00
00 01 80 00 00 01 14 01 00 01 2a 01 00 01 2f 01
00 01 82 01 0d 01 0e 01 0f 01 20 01 92 01 93 01
94 01 95 01 96 01 a2 01 a3 01 a4 01 a5 01 a6 01
VESA: 50 mode(s) found
VESA: v2.0, 8192k memory, flags:0x1, mode table:0xc07962c2 (1000022)
VESA: ATI MOBILITY RADEON
VESA: ATI Technologies Inc. R100 01.00
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <FUJ    PAULING3> on motherboard
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80003074
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=80] is there (id=03951279)
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fdf30
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    2    A   0x59  3 4 5 7 10 11
embedded    0    4    A   0x08  3 4 5 7 9 10 14 15
embedded    0   12    A   0x01  3 4 5 7 9 10 14 15
embedded    0   16    A   0x02  3 4 5 7 9 10 14 15
embedded    0   18    A   0x05  3 4 5 7 9 10 14 15
embedded    0   18    B   0x06  3 4 5 7 9 10 14 15
embedded    0   19    A   0x03  3 4 5 7 9 10 14 15
embedded    0   20    A   0x04  3 4 5 7 9 10 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 6 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 6 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 12 func 0
acpi0: Power Button (fixed)
ACPI timer looks BAD  min = 2, max = 755, width = 753
ACPI timer looks BAD  min = 2, max = 7, width = 5
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks BAD  min = 2, max = 9, width = 7
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks GOOD min = 2, max = 4, width = 2
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xff08-0xff0b on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.EIO_.LNKU irq  11: [  3  4  5  7  9 10 11] 
low,level,sharable 0.2.0
\\_SB_.PCI0.EIO_.LNKH irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.4.0
\\_SB_.PCI0.EIO_.LNKA irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.9.0
\\_SB_.PCI0.EIO_.LNKB irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.9.1
\\_SB_.PCI0.EIO_.LNKC irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.9.2
\\_SB_.PCI0.EIO_.LNKA irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.12.0
\\_SB_.PCI0.EIO_.LNKC irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.19.0
\\_SB_.PCI0.EIO_.LNKD irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.20.0
\\_SB_.PCI0.EIO_.LNKB irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.16.0
\\_SB_.PCI0.EIO_.LNKE irq   0: [  3  4  5  7  9 10 11] 
low,level,sharable 0.18.0
\\_SB_.PCI0.EIO_.LNKF irq   0: [  3  4  5  7  9 10 11] 
low,level,sharable 0.18.1
---- before setting priority for links ------------
\\_SB_.PCI0.EIO_.LNKE:
	interrupts:	     3     4     5     7     9    10    11
	penalty:	  1220  1220   220  1220  1020   220   320
	references:	1
	priority:	0
\\_SB_.PCI0.EIO_.LNKF:
	interrupts:	     3     4     5     7     9    10    11
	penalty:	  1220  1220   220  1220  1020   220   320
	references:	1
	priority:	0
---- before fixup boot-disabled links -------------
\\_SB_.PCI0.EIO_.LNKE:
	interrupts:	     3     4     5     7     9    10    11
	penalty:	  1220  1220   220  1220  1020   220   320
	references:	1
	priority:	777
\\_SB_.PCI0.EIO_.LNKF:
	interrupts:	     3     4     5     7     9    10    11
	penalty:	  1220  1220   220  1220  1020   220   320
	references:	1
	priority:	777
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.EIO_.LNKU irq  11: [  3  4  5  7  9 10 11] 
low,level,sharable 0.2.0
\\_SB_.PCI0.EIO_.LNKH irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.4.0
\\_SB_.PCI0.EIO_.LNKA irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.9.0
\\_SB_.PCI0.EIO_.LNKB irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.9.1
\\_SB_.PCI0.EIO_.LNKC irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.9.2
\\_SB_.PCI0.EIO_.LNKA irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.12.0
\\_SB_.PCI0.EIO_.LNKC irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.19.0
\\_SB_.PCI0.EIO_.LNKD irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.20.0
\\_SB_.PCI0.EIO_.LNKB irq   9: [  3  4  5  7  9 10 11] 
low,level,sharable 0.16.0
\\_SB_.PCI0.EIO_.LNKE irq  10: [  3  4  5  7  9 10 11] 
low,level,sharable 0.18.0
\\_SB_.PCI0.EIO_.LNKF irq   5: [  3  4  5  7  9 10 11] 
low,level,sharable 0.18.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 1, range 32, base e8100000, size 20, enabled
found->	vendor=0x1279, dev=0x0395, revid=0x03
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1279, dev=0x0396, revid=0x00
	bus=0, slot=0, func=1
	class=05-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1279, dev=0x0397, revid=0x00
	bus=0, slot=0, func=2
	class=05-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 1, range 32, base e8014000, size 12, enabled
pcib0: matched entry for 0.2.INTA (source \\_SB_.PCI0.EIO_.LNKU)
pcib0: slot 2 INTA is routed to irq 11
found->	vendor=0x10b9, dev=0x5237, revid=0x03
	bus=0, slot=2, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00001000, size  8, enabled
	map[14]: type 1, range 32, base e8015000, size 12, enabled
pcib0: matched entry for 0.4.INTA (source \\_SB_.PCI0.EIO_.LNKH)
pcib0: slot 4 INTA is routed to irq 9
found->	vendor=0x10b9, dev=0x5451, revid=0x01
	bus=0, slot=4, func=0
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x10b9, dev=0x7101, revid=0x00
	bus=0, slot=6, func=0
	class=06-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x10b9, dev=0x1533, revid=0x00
	bus=0, slot=7, func=0
	class=06-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x000f, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	powerspec 1  supports D0 D3  current D0
found->	vendor=0x1033, dev=0x0035, revid=0x41
	bus=0, slot=9, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x08 (240 ns), mingnt=0x01 (250 ns), maxlat=0x2a (10500 ns)
	intpin=a, irq=255
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x1033, dev=0x0035, revid=0x41
	bus=0, slot=9, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x08 (240 ns), mingnt=0x01 (250 ns), maxlat=0x2a (10500 ns)
	intpin=b, irq=255
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x1033, dev=0x00e0, revid=0x02
	bus=0, slot=9, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x44 (2040 ns), mingnt=0x10 (4000 ns), maxlat=0x22 (8500 ns)
	intpin=c, irq=255
	powerspec 2  supports D0 D1 D2 D3  current D0
pcib0: matched entry for 0.12.INTA (source \\_SB_.PCI0.EIO_.LNKA)
pcib0: slot 12 INTA is routed to irq 9
found->	vendor=0x104c, dev=0xac50, revid=0x01
	bus=0, slot=12, func=0
	class=06-07-00, hdrtype=0x02, mfdev=0
	cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns)
	intpin=a, irq=9
	powerspec 1  supports D0 D1 D2 D3  current D0
	map[20]: type 4, range 32, base 00001800, size  4, enabled
found->	vendor=0x10b9, dev=0x5229, revid=0xc3
	bus=0, slot=15, func=0
	class=01-01-fa, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
	intpin=a, irq=255
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00008000, size  8, enabled
	map[14]: type 1, range 32, base e8016800, size  8, enabled
pcib0: matched entry for 0.16.INTA (source \\_SB_.PCI0.EIO_.LNKB)
pcib0: slot 16 INTA is routed to irq 9
found->	vendor=0x10ec, dev=0x8139, revid=0x10
	bus=0, slot=16, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 
(16000 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base e8016000, size 11, enabled
	map[14]: type 1, range 32, base e8010000, size 14, enabled
pcib0: matched entry for 0.19.INTA (source \\_SB_.PCI0.EIO_.LNKC)
pcib0: slot 19 INTA is routed to irq 9
found->	vendor=0x104c, dev=0x8026, revid=0x00
	bus=0, slot=19, func=0
	class=0c-00-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 3, range 32, base f0000000, size 27, enabled
	map[14]: type 4, range 32, base 00001400, size  8, enabled
	map[18]: type 1, range 32, base e8000000, size 16, enabled
pcib0: matched entry for 0.20.INTA (source \\_SB_.PCI0.EIO_.LNKD)
pcib0: slot 20 INTA is routed to irq 9
found->	vendor=0x1002, dev=0x4c59, revid=0x00
	bus=0, slot=20, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0083, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 
0xe8014000-0xe8014fff irq 11 at device 2.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
pcm0: <Acer Labs M5451> port 0x1000-0x10ff mem 
0xe8015000-0xe8015fff irq 9 at device 4.0 on pci0
pcm0: <Unknown AC97 Codec (id = 0x83847666)>
pcm0: Codec features headphone, 20 bit DAC, 18 bit ADC, 5 bit 
master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features variable rate PCM, reserved 
1, AMAP, reserved 4
pcm0: sndbuf_setmap 274000, 1000; 0xc38e0000 -> 274000
pcm0: sndbuf_setmap 164b2000, 1000; 0xc38de000 -> 164b2000
pcm0: sndbuf_setmap 164b0000, 1000; 0xc38dc000 -> 164b0000
pcm0: sndbuf_setmap 2ac000, 1000; 0xc38f8000 -> 2ac000
pcm0: sndbuf_setmap 28a000, 1000; 0xc38f6000 -> 28a000
alpm0: <AcerLabs M15x3 Power Management Unit> at device 6.0 on pci0
alpm0: nohost/noslave 149K
alpm0: failed to enable port mapping!
alpm0: Could not allocate Bus space
device_probe_and_attach: alpm0 attach returned 6
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
ohci1: <NEC uPD 9210 USB controller> at device 9.0 on pci0
ohci1: Could not map memory
device_probe_and_attach: ohci1 attach returned 6
ohci1: <NEC uPD 9210 USB controller> at device 9.1 on pci0
ohci1: Could not map memory
device_probe_and_attach: ohci1 attach returned 6
pci0: <serial bus, USB> at device 9.2 (no driver attached)
pci0: <bridge, PCI-CardBus> at device 12.0 (no driver attached)
atapci0: <AcerLabs Aladdin UDMA66 controller> port 0x1800-0x180f 
at device 15.0 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
rl0: <RealTek 8139 10/100BaseTX> port 0x8000-0x80ff mem 
0xe8016800-0xe80168ff irq 9 at device 16.0 on pci0
rl0: Ethernet address: 00:e0:00:fa:91:a7
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
fwohci0: vendor=104c, dev=8026
fwohci0: <1394 Open Host Controller Interface> mem 
0xe8010000-0xe8013fff,0xe8016000-0xe80167ff irq 9 at device 19.0 
on pci0
fwohci0: latency timer 64 -> 64.
fwohci0: cache size 8 -> 8.
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:00:0e:10:00:f0:49:b0
fwohci0: resetting OHCI...done (loop=0)
fwohci0: fwphy_rddata: 0x2 loop=0, retry=0
fwohci0: fwphy_rddata: 0x3 loop=0, retry=0
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: fwphy_rddata: 0x5 loop=0, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=0, retry=0
fwohci0: fwphy_rddata: 0x2 loop=0, retry=0
fwohci0: fwphy_rddata: 0x4 loop=0, retry=0
fwohci0: fwphy_rddata: 0x4 loop=0, retry=0
fwohci0: fwphy_rddata: 0x4 loop=0, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
sbp_attach (cold=1)
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:0e:f0:49:b0
fwe0: bpf attached
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=0, retry=0
fwohci0: fwphy_rddata: 0x1 loop=0, retry=0
fwohci0: BUS reset
sbp_post_busreset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
drm0: <ATI Radeon LY Mobility M6> port 0x1400-0x14ff mem 
0xe8000000-0xe800ffff,0xf0000000-0xf7ffffff irq 9 at device 20.0 
on pci0
info: [drm] Initialized radeon 1.10.0 20020828 on minor 0
acpi_button0: <Power Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x54ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
acpi_ec0: <Embedded Controller: GPE 0> port 0x66,0x62 on acpi0
unknown: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
vt: vt0 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcdfff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0 failed to probe at port 0x3f8 irq 4 flags 0x10 on isa0
sio1 failed to probe at port 0x2f8 irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff 
on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on 
this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 ce 4f 77 8a 7d 8b
24 b3 00 6f 0d 0e 00 00 07 80 49 8f 8f 28 1f 47
6d a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 ce 4f 77 8a 7d 8b
24 b3 00 6f 0d 0e 00 00 07 80 49 8f 8f 28 1f 47
6d a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 666313999 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
Current DB 0
ch = 0
  Current OP   KEY INT BR   len     Addr   Depend Stat: Cnt
00268000 OUTL ST2 ALL ALL    12 00000000 00268080 8411:0014 
RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 
100.0%
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
acpi_cmbat1: battery initialization start
ata0-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin
ata0-master: setting PIO4 on AcerLabs Aladdin chip
ata0-master: setting UDMA66 on AcerLabs Aladdin chip
GEOM: create disk ad0 dp=0xc3a7e060
ad0: <IBM-DJSA-220/JS4OAC9A> ATA-5 disk at ata0-master
ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA66
GEOM: new disk ad0
bus_explore done
sbp_post_explore (sbp_cold=2)
ar: FreeBSD check1 failed
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/15/63 s:63 l:39070017
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 20003848704 end 20003880959
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
ata1-master: setting PIO4 on AcerLabs Aladdin chip
GEOM: Configure ad0s1a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s1b, start 268435456 length 745152512 end 
1013587967
GEOM: Configure ad0s1c, start 0 length 20003848704 end 20003848703
GEOM: Configure ad0s1d, start 1013587968 length 268435456 end 
1282023423
GEOM: Configure ad0s1e, start 1282023424 length 268435456 end 
1550458879
GEOM: Configure ad0s1f, start 1550458880 length 18453389824 end 
20003848703
acd0: <TOSHIBA DVD-ROM SD-R2212/1F17> CDRW drive at ata1 as master
acd0: read 4134KB/s (4134KB/s) write 2755KB/s (2755KB/s), 2048KB 
buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe2:ata1:0:0:0): Retrying Command
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe2:ata1:0:0:0): Retrying Command
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe9:sbp0:0:5:0): error 22
(probe9:sbp0:0:5:0): Unretryable Error
(probe4:sbp0:0:0:0): error 22
(probe4:sbp0:0:0:0): Unretryable Error
(probe5:sbp0:0:1:0): error 22
(probe5:sbp0:0:1:0): Unretryable Error
(probe6:sbp0:0:2:0): error 22
(probe6:sbp0:0:2:0): Unretryable Error
(probe7:sbp0:0:3:0): error 22
(probe7:sbp0:0:3:0): Unretryable Error
(probe8:sbp0:0:4:0): error 22
(probe8:sbp0:0:4:0): Unretryable Error
(probe10:sbp0:0:6:0): error 22
(probe10:sbp0:0:6:0): Unretryable Error
pass0 at ata1 bus 0 target 0 lun 0
pass0: <TOSHIBA DVD-ROM SD-R2212 1F17> Removable CD-ROM SCSI-0 device
pass0: 16.000MB/s transfers
GEOM: create disk cd0 dp=0xc38ea600
GEOM: new disk cd0
(cd0:ata1:0:0:0): Retrying Command
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <TOSHIBA DVD-ROM SD-R2212 1F17> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not 
present
(cd0:ata1:0:0:0): Retrying Command
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): Retrying Command
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
acpi_cmbat1: battery initialization failed, giving up
Linux ELF exec handler installed


Peter Schultz wrote:

 > Erich Dollansky wrote:
 >
 >> Is there any site describing what can be done to get ACPI running?
 >>
 >
 > http://bis.midco.net/pmes/acpi.html
 >
 > HTH,
 > Pete...
 > _______________________________________________
 > freebsd-current_at_freebsd.org mailing list
 > http://lists.freebsd.org/mailman/listinfo/freebsd-current
 > To unsubscribe, send any mail to 
"freebsd-current-unsubscribe_at_freebsd.org"
 >
Received on Fri Jan 23 2004 - 08:46:20 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:39 UTC