I just updated a RELENG_5 system from sometime around 5.3-BETA4 (17 September) to very late 5.3-BETA6 (just before the 5.3-BETA7 version number bump) and it's now hanging after probing its DVD drive. This problem sounds vaguely like what was described in the thread "ATTN Soren: BETA3 still hangs on ATAPI DVD Detection during boot": http://lists.freebsd.org/pipermail/freebsd-current/2004-September/036543.html The interesting thing is that my system appeared to be working just fine with the BETA4 code. I've appended verbose boot output from BETA4, as well as the lines that I think were relevant from a BETA6 boot, at least up to the point where it hung. The latter output is hand-copied. The system isn't totally wedged because I can page back through the console's scrollback buffer, but the kernel just doesn't seem to finish probing and attaching devices. I tried disabling ATAPI DMA as Soren suggested in the thread above by setting hw.ata.atapi_dma=0 from the loader; this seemed to have no effect. I tried backing out the ata driver updates from 30 September to see if that might help matters, but it didn't seem to help. Neither did booting the kernel from the 5.3-BETA6 bootonly iso image; that hangs in exactly the same way. At this point I'm kind of flailing around at random. At first I had suspected the ata(4) driver but the evidence I've seen so far doesn't really point in that direction. Any ideas? Thanks for any suggestions! Bruce. ----- (5.3-BETA4 boot. This kernel was built from source shortly before 5.3-BETA5.) FreeBSD 5.3-BETA4 #4: Fri Sep 17 13:00:00 PDT 2004 root_at_tomcat.kitchenlab.org:/usr/obj/usr/src/sys/NIMITZ5 Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a37000. Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0a37228. Preloaded elf module "/boot/kernel/sound.ko" at 0xc0a372d4. Preloaded elf module "/boot/kernel/uvisor.ko" at 0xc0a37380. Preloaded elf module "/boot/kernel/ucom.ko" at 0xc0a3742c. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a374d8. Calibrating clock(s) ... i8254 clock: 1193183 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 996749528 Hz CPU: Intel Pentium III (996.75-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 535691264 (510 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000001f5b4fff, 513327104 bytes (125324 pages) avail memory = 514519040 (490 MB) bios32: Found BIOS32 Service Directory header at 0xc00fdad0 bios32: Entry = 0xfdae0 (c00fdae0) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xdb01 pnpbios: Found PnP BIOS data at 0xc00f6830 pnpbios: Entry = f0000:5834 Rev = 1.0 Other BIOS signatures found: wlan: <802.11 Link Layer> random: <entropy source, Software, Yarrow> io: <I/O> mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <AMIINT AMIINT10> on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=11308086) pcibios: BIOS version 2.10 Found $PIR table, 8 entries at 0xc00f6e20 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 2 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 31 A 0xfe 14 embedded 0 31 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 31 C 0x6b 3 4 5 7 9 10 11 12 14 15 embedded 0 31 D 0x63 3 4 5 7 9 10 11 12 14 15 slot 1 1 3 A 0x61 4 5 6 7 9 10 11 12 14 slot 1 1 3 B 0x62 4 5 6 7 9 10 11 12 14 slot 1 1 3 C 0x63 4 5 6 7 9 10 11 12 14 slot 1 1 3 D 0x60 4 5 6 7 9 10 11 12 14 slot 2 1 4 A 0x61 4 5 6 7 9 10 11 12 14 slot 2 1 4 B 0x62 4 5 6 7 9 10 11 12 14 slot 2 1 4 C 0x63 4 5 6 7 9 10 11 12 14 slot 2 1 4 D 0x60 4 5 6 7 9 10 11 12 14 slot 3 1 5 A 0x61 4 5 6 7 9 10 11 12 14 slot 3 1 5 B 0x62 4 5 6 7 9 10 11 12 14 slot 3 1 5 C 0x63 4 5 6 7 9 10 11 12 14 slot 3 1 5 D 0x60 4 5 6 7 9 10 11 12 14 embedded 1 2 A 0x60 4 5 6 7 9 10 11 12 14 embedded 1 2 B 0x61 4 5 6 7 9 10 11 12 14 embedded 1 8 A 0x68 4 5 6 7 9 10 11 12 14 AcpiOsDerivePciId: bus 1 dev 2 func 0 AcpiOsDerivePciId: bus 1 dev 2 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) AcpiOsDerivePciId: bus 0 dev 0 func 0 AcpiOsDerivePciId: bus 0 dev 0 func 0 AcpiOsDerivePciId: bus 0 dev 0 func 0 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 unknown: not probed (disabled) unknown: not probed (disabled) cpu0: <ACPI CPU (3 Cx states)> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ACPI PCI link initial configuration: \\_SB_.LNKB irq 0: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 0.31.1 \\_SB_.LNKH irq 0: [ 4 5 6 7 9 10 11 12 14] 10+ low,level,sharable 0.31.2 \\_SB_.LNKD irq 0: [ 4 5 6 7 9 10 11 12 14] 5+ low,level,sharable 0.31.3 \\_SB_.LNKA irq 0: [ 4 5 6 7 9 10 11 12 14] 9+ low,level,sharable 0.1.0 \\_SB_.LNKB irq 0: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 0.1.1 \\_SB_.LNKC irq 0: [ 4 5 6 7 9 10 11 12 14] 0+ low,level,sharable 0.1.2 \\_SB_.LNKD irq 0: [ 4 5 6 7 9 10 11 12 14] 5+ low,level,sharable 0.1.3 \\_SB_.LNKA irq 0: [ 4 5 6 7 9 10 11 12 14] 9+ low,level,sharable 0.2.0 \\_SB_.LNKB irq 0: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 0.2.1 \\_SB_.LNKC irq 0: [ 4 5 6 7 9 10 11 12 14] 0+ low,level,sharable 0.2.2 \\_SB_.LNKD irq 0: [ 4 5 6 7 9 10 11 12 14] 5+ low,level,sharable 0.2.3 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x1130, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 3, range 32, base e8000000, size 26, enabled map[14]: type 1, range 32, base eff80000, size 19, enabled pcib0: matched entry for 0.2.INTA (src \\_SB_.LNKA) pcib0: possible interrupts: 4 5 6 7 9 10 11 12 14 ACPI PCI link arbitrated settings: \\_SB_.LNKB (references 3, priority 23716): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 110 110 160 220 5110 5110 5110 5110 50110 \\_SB_.LNKD (references 3, priority 23716): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 110 110 160 220 5110 5110 5110 5110 50110 \\_SB_.LNKA (references 2, priority 15811): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 110 110 160 220 5110 5110 5110 5110 50110 \\_SB_.LNKC (references 2, priority 15811): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 110 110 160 220 5110 5110 5110 5110 50110 \\_SB_.LNKH (references 1, priority 7905): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 110 110 160 220 5110 5110 5110 5110 50110 pcib0: slot 2 INTA routed to irq 9 via \\_SB_.LNKA found-> vendor=0x8086, dev=0x1132, revid=0x02 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x244e, revid=0x11 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2440, revid=0x11 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000ffa0, size 4, enabled found-> vendor=0x8086, dev=0x244b, revid=0x11 bus=0, slot=31, func=1 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000cc00, size 5, enabled pcib0: matched entry for 0.31.INTD (src \\_SB_.LNKD) pcib0: possible interrupts: 4 5 6 7 9 10 11 12 14 ACPI PCI link arbitrated settings: \\_SB_.LNKB (references 3, priority 24090): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 220 240 270 440 5220 5220 5220 5220 50220 \\_SB_.LNKD (references 3, priority 24090): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 220 240 270 440 5220 5220 5220 5220 50220 \\_SB_.LNKC (references 2, priority 16060): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 220 240 270 440 5220 5220 5220 5220 50220 \\_SB_.LNKH (references 1, priority 8030): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 220 240 270 440 5220 5220 5220 5220 50220 pcib0: slot 31 INTD routed to irq 5 via \\_SB_.LNKD found-> vendor=0x8086, dev=0x2442, revid=0x11 bus=0, slot=31, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=5 map[20]: type 4, range 32, base 00000540, size 4, enabled pcib0: matched entry for 0.31.INTB (src \\_SB_.LNKB) pcib0: possible interrupts: 4 5 6 7 9 10 11 12 14 ACPI PCI link arbitrated settings: \\_SB_.LNKB (references 3, priority 24466): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 330 350 410 660 5330 5330 5330 5330 50330 \\_SB_.LNKC (references 2, priority 16311): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 330 350 410 660 5330 5330 5330 5330 50330 \\_SB_.LNKH (references 1, priority 8155): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 330 350 410 660 5330 5330 5330 5330 50330 pcib0: slot 31 INTB routed to irq 11 via \\_SB_.LNKB found-> vendor=0x8086, dev=0x2443, revid=0x11 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type 4, range 32, base 0000d400, size 5, enabled pcib0: matched entry for 0.31.INTC (src \\_SB_.LNKH) pcib0: possible interrupts: 4 5 6 7 9 10 11 12 14 ACPI PCI link arbitrated settings: \\_SB_.LNKC (references 2, priority 16562): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 440 460 520 910 5440 5440 5440 5440 50440 \\_SB_.LNKH (references 1, priority 8281): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 440 460 520 910 5440 5440 5440 5440 50440 pcib0: slot 31 INTC routed to irq 10 via \\_SB_.LNKH found-> vendor=0x8086, dev=0x2444, revid=0x11 bus=0, slot=31, func=4 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=10 map[10]: type 4, range 32, base 0000dc00, size 8, enabled map[14]: type 4, range 32, base 0000d800, size 6, enabled pcib0: matched entry for 0.31.INTB (src \\_SB_.LNKB) pcib0: slot 31 INTB is already routed to irq 11 found-> vendor=0x8086, dev=0x2445, revid=0x11 bus=0, slot=31, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem 0xeff80000-0xefffffff,0xe8000000-0xebffffff irq 9 at device 2.0 on pci0 agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe8000000 agp0: Reserved 0x80000 bytes for rid 0x14 type 3 at 0xeff80000 pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xa000-0xafff pcib1: memory decode 0xefd00000-0xefdfffff pcib1: prefetched decode 0xe7b00000-0xe7bfffff pcib1: Subtractively decoded bridge. ACPI PCI link initial configuration: \\_SB_.LNKB irq*11: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 1.3.0 \\_SB_.LNKC irq 0: [ 4 5 6 7 9 10 11 12 14] 0+ low,level,sharable 1.3.1 \\_SB_.LNKD irq* 5: [ 4 5 6 7 9 10 11 12 14] 5+ low,level,sharable 1.3.2 \\_SB_.LNKA irq* 9: [ 4 5 6 7 9 10 11 12 14] 9+ low,level,sharable 1.3.3 \\_SB_.LNKC irq 0: [ 4 5 6 7 9 10 11 12 14] 0+ low,level,sharable 1.4.0 \\_SB_.LNKD irq* 5: [ 4 5 6 7 9 10 11 12 14] 5+ low,level,sharable 1.4.1 \\_SB_.LNKA irq* 9: [ 4 5 6 7 9 10 11 12 14] 9+ low,level,sharable 1.4.2 \\_SB_.LNKB irq*11: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 1.4.3 \\_SB_.LNKD irq* 5: [ 4 5 6 7 9 10 11 12 14] 5+ low,level,sharable 1.5.0 \\_SB_.LNKA irq* 9: [ 4 5 6 7 9 10 11 12 14] 9+ low,level,sharable 1.5.1 \\_SB_.LNKB irq*11: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 1.5.2 \\_SB_.LNKC irq 0: [ 4 5 6 7 9 10 11 12 14] 0+ low,level,sharable 1.5.3 \\_SB_.LNKA irq* 9: [ 4 5 6 7 9 10 11 12 14] 9+ low,level,sharable 1.2.0 \\_SB_.LNKB irq*11: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 1.2.1 \\_SB_.LNKE irq 0: [ 4 5 6 7 9 10 11 12 14] 11+ low,level,sharable 1.8.0 pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 32, base 00000000, size 12, enabled found-> vendor=0x104c, dev=0xac41, revid=0x02 bus=1, slot=2, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0xc0 (48000 ns), maxlat=0x04 (1000 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base efdff800, size 11, enabled pcib1: device (null) requested decoded memory range 0xefdff800-0xefdfffff map[14]: type 1, range 32, base efdf8000, size 14, enabled pcib1: device (null) requested decoded memory range 0xefdf8000-0xefdfbfff pcib1: matched entry for 1.2.INTB (src \\_SB_.LNKB) pcib1: slot 2 INTB is already routed to irq 11 found-> vendor=0x104c, dev=0x8017, revid=0x02 bus=1, slot=2, func=1 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0116, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=b, irq=11 powerspec 1 supports D0 D2 D3 current D0 map[10]: type 1, range 32, base efdfe000, size 12, enabled pcib1: device (null) requested decoded memory range 0xefdfe000-0xefdfefff map[14]: type 4, range 32, base 0000ac00, size 6, enabled pcib1: device (null) requested decoded I/O range 0xac00-0xac3f pcib1: matched entry for 1.8.INTA (src \\_SB_.LNKE) pcib1: possible interrupts: 4 5 6 7 9 10 11 12 14 ACPI PCI link arbitrated settings: \\_SB_.LNKC (references 5, priority 42911): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 750 760 820 1210 5740 5740 5740 5740 50740 \\_SB_.LNKE (references 1, priority 8582): interrupts: 10 9 5 11 12 7 6 4 14 penalty: 750 760 820 1210 5740 5740 5740 5740 50740 pcib1: slot 8 INTA routed to irq 11 via \\_SB_.LNKE found-> vendor=0x8086, dev=0x2449, revid=0x03 bus=1, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 cbb0: <TI4410 PCI-CardBus Bridge> at device 2.0 on pci1 pcib1: device cbb0 requested decoded memory range 0xefd00000-0xefdfffff cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xefd00000 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 pcib1: matched entry for 1.2.INTA (src \\_SB_.LNKA) pcib1: slot 2 INTA is already routed to irq 9 cbb0: [MPSAFE] cbb0: PCI Configuration space: 0x00: 0xac41104c 0x02100007 0x06070002 0x00822000 0x10: 0xefd00000 0x020000a0 0x20030201 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x04400109 0x40: 0x89a71509 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x08249060 0x00000400 0x00000000 0x00001000 0x90: 0x216400c0 0x00000000 0x00000000 0x00000000 0xa0: 0xfe110001 0x00c00100 0x0000000a 0x0000001f 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 fwohci0: <Texas Instruments PCI4410A> mem 0xefdf8000-0xefdfbfff,0xefdff800-0xefdfffff irq 11 at device 2.1 on pci1 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xefdff800 fwohci0: [MPSAFE] fwohci0: OHCI version 1.0 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:40:ca:07:02:00:53:e4 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:40:ca:00:53:e4 fwe0: bpf attached fwe0: Ethernet address: 02:40:ca:00:53:e4 fwe0: if_start running deferred for Giant sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) fxp0: <Intel 82801BA/CAM (ICH2/3) Pro/100 Ethernet> port 0xac00-0xac3f mem 0xefdfe000-0xefdfefff irq 11 at device 8.0 on pci1 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xefdfe000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 2449 8086 3013 0003 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82562ET 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:40:ca:28:84:c9 fxp0: [MPSAFE] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH2 UDMA100 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0 ata0: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: [MPSAFE] ata1: channel #1 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=01 ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata1: [MPSAFE] uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xcc00-0xcc1f irq 5 at device 31.2 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xcc00 uhci0: [GIANT-LOCKED] usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <serial bus, SMBus> at device 31.3 (no driver attached) uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0xd400-0xd41f irq 10 at device 31.4 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd400 uhci1: [GIANT-LOCKED] usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pcm0: <Intel ICH2 (82801BA)> port 0xd800-0xd83f,0xdc00-0xdcff irq 11 at device 31.5 on pci0 pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xdc00 pcm0: Reserved 0x40 bytes for rid 0x14 type 4 at 0xd800 pcm0: [GIANT-LOCKED] pcm0: <Cirrus Logic CS4299 AC97 Codec (id = 0x43525934)> pcm0: Codec features headphone, 20 bit DAC, 18 bit ADC, 6 bit master volume, Crystal Semi 3D Stereo Enhancement pcm0: Primary codec extended features variable rate PCM, AMAP pcm0: sndbuf_setmap 1f07e000, 4000; 0xd96c1000 -> 1f07e000 pcm0: sndbuf_setmap 1f074000, 4000; 0xd96c5000 -> 1f074000 acpi_button0: <Power Button> on acpi0 unknown: not probed (disabled) psmcpnp0 irq 12 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000008, packet size:3 psm0: syncmask:c0, syncbits:00 fdc0: <floppy drive controller> port 0x3f7,0x3f4-0x3f5,0x3f0-0x3f3 irq 6 drq 2 on acpi0 fdc0: output ready timeout fdc0: cmd 3 failed at out byte 1 of 3 device_attach: fdc0 attach returned 6 sio0: irq maps: 0x801 0x811 0x801 0x801 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A unknown: not probed (disabled) ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) fdc0: <floppy drive controller> port 0x3f7,0x3f4-0x3f5,0x3f0-0x3f3 irq 6 drq 2 on acpi0 fdc0: output ready timeout fdc0: cmd 3 failed at out byte 1 of 3 device_attach: fdc0 attach returned 6 unknown: not probed (disabled) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ahc_isa_probe 10: ioport 0xac00 alloc failed ahc_isa_probe 12: ioport 0xcc00 alloc failed ahc_isa_probe 13: ioport 0xdc00 alloc failed sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROMs> at iomem 0xe0000-0xe0fff,0xc0000-0xcbfff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x801 0x801 0x801 0x801 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 996749528 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: setting PIO4 on Intel ICH2 chip ata0-master: setting UDMA100 on Intel ICH2 chip ad0: <ST3120026A/3.06> ATA-6 disk at ata0-master ad0: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ar: FreeBSD check1 failed ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ATAPI_RESET time = 670us ata1-master: setting PIO4 on Intel ICH2 chip ata1-master: setting UDMA33 on Intel ICH2 chip acd0: <SONY DVD RW DRU-530A/1.0d> DVDR drive at ata1 as master acd0: read 6890KB/s (6890KB/s) write 4133KB/s (4133KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: CDR, CDRW, DVDR, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc pcm0: measured ac97 link rate at 47998 Hz, will use 48000 Hz [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:167766732 [1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:167766795 l:66669750 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 85896566784 end 85896599039 GEOM: Configure ad0s2, start 85896599040 length 34134912000 end 120031511039 GEOM: Configure ad0s1a, start 0 length 536870912 end 536870911 GEOM: Configure ad0s1b, start 536870912 length 1073741824 end 1610612735 GEOM: Configure ad0s1c, start 0 length 85896566784 end 85896566783 GEOM: Configure ad0s1d, start 1610612736 length 1073741824 end 2684354559 GEOM: Configure ad0s1e, start 2684354560 length 21474836480 end 24159191039 GEOM: Configure ad0s1f, start 24159191040 length 21474836480 end 45634027519 GEOM: Configure ad0s1g, start 45634027520 length 40262539264 end 85896566783 GEOM: Configure ad0s2a, start 0 length 536870912 end 536870911 GEOM: Configure ad0s2c, start 0 length 34134912000 end 34134911999 GEOM: Configure ad0s2e, start 536870912 length 1073741824 end 1610612735 GEOM: Configure ad0s2f, start 1610612736 length 1073741824 end 2684354559 GEOM: Configure ad0s2g, start 2684354560 length 21474836480 end 24159191039 GEOM: Configure ad0s2h, start 24159191040 length 9975720960 end 34134911999 (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:ata0:0:1:0): error 22 (probe1:ata0:0:1:0): Unretryable Error (probe3:ata1:0:1:0): error 22 (probe3:ata1:0:1:0): Unretryable Error (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:ata0:0:1:0): error 22 (probe1:ata0:0:1:0): Unretryable Error (probe3:ata1:0:1:0): error 22 (probe3:ata1:0:1:0): Unretryable Error (probe2:ata1:0:0:0): error 6 (probe2:ata1:0:0:0): Unretryable Error (probe6:sbp0:0:2:0): error 22 (probe6:sbp0:0:2:0): Unretryable Error (probe7:sbp0:0:3:0): error 22 (probe7:sbp0:0:3:0): Unretryable Error (probe8:sbp0:0:4:0): error 22 (probe8:sbp0:0:4:0): Unretryable Error (probe9:sbp0:0:5:0): error 22 (probe9:sbp0:0:5:0): Unretryable Error (probe10:sbp0:0:6:0): error 22 (probe10:sbp0:0:6:0): Unretryable Error (probe4:sbp0:0:0:0): error 22 (probe4:sbp0:0:0:0): Unretryable Error (probe5:sbp0:0:1:0): error 22 (probe5:sbp0:0:1:0): Unretryable Error pass0 at ata1 bus 0 target 0 lun 0 pass0: <SONY DVD RW DRU-530A 1.0d> Removable CD-ROM SCSI-0 device pass0: Serial Number 3 pass0: 33.000MB/s transfers GEOM: new disk cd0 (cd0:ata1:0:0:0): error 6 (cd0:ata1:0:0:0): Unretryable Error cd0 at ata1 bus 0 target 0 lun 0 cd0: <SONY DVD RW DRU-530A 1.0d> Removable CD-ROM SCSI-0 device cd0: Serial Number 3 cd0: 33.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed (cd0:ata1:0:0:0): error 6 (cd0:ata1:0:0:0): Unretryable Error (cd0:ata1:0:0:0): error 6 (cd0:ata1:0:0:0): Unretryable Error (cd0:ata1:0:0:0): error 6 (cd0:ata1:0:0:0): Unretryable Error Mounting root from ufs:/dev/ad0s1a start_init: trying /sbin/init Linux ELF exec handler installed linprocfs registered splash: image decoder found: logo_saver ----- (Selected lines from 5.3-BETA6 kernel, built just prior to 5.3-BETA7 version bump. Copied by hand.) atapci0: <Intel ICH2 UDMA100 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid0x20 type 4 at 0xffa0 ata0: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat 0x90 err=0x90 lsb=0x90 msb=0x90 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: [MPSAFE] ata1: channel #1 on atapci0 atapi0: Reserved 0x08 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=01 ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata1: [MPSAFE] ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: setting PIO4 on Intel ICH2 chip ata0-master: setting UDMA100 on Intel ICH2 chip ad0: <ST3120026A/3.06> ATA-6 disk at ata0-master ad0: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512B ad0: 16 secs/int, 1 depth queue, UDMA100 ar: FreeBSD check1 failed ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata1-master: setting PIO4 on Intel ICH2 chip ata1-master: setting UDMA33 on Intel ICH2 chip acd0: <SONY DVD RW DRU-530A/1.0d> DVDR drive at ata1 as master acd0: read 6890KB/s (6890KB/s) write 4133KB/s (4133KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: CDR, CDRW, DVDR, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disk
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:15 UTC