I've been searching around for what I might be doing incorrectly, but seem to have come to a dead stop in setting up a HP Proliant DL380G3 machine with a PAE enabled 5.3-BETA kernel. I've tried BETAS 3,4, and 5 with no luck. The default PAE configuration file causes the problem indicated in the log below. FOO is a copy of PAE config with KDB, DDB, and KVA_PAGES=512. Am I incorrect in assuming this should work on 5.3? (n.b. I also tried reducing the RAM from 8G to 5G with identical results) At the atapci and the bge probe and attach phases the machine slugs for 150 seconds or so before continuing. And of course, panics after loading the kernel. Regards, Kevin M. Dulzo KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-BETA5 #1: Mon Sep 20 16:55:12 CDT 2004 kdulzo_at_jirayi-san:/usr/src/sys/i386/compile/FOO ACPI APIC Table: <COMPAQ 00000083> Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Xeon(TM) CPU 3.20GHz (3185.21-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf25 Stepping = 5 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 8589930496 (8191 MB) avail memory = 8149667840 (7772 MB) FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 6 cpu3 (AP): APIC ID: 7 MADT: Forcing active-low polarity and level trigger for SCI ioapic0 <Version 1.1> irqs 0-15 on motherboard ioapic1 <Version 1.1> irqs 16-31 on motherboard ioapic2 <Version 1.1> irqs 32-47 on motherboard ioapic3 <Version 1.1> irqs 48-63 on motherboard acpi0: <COMPAQ P29> on motherboard acpi0: Power Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x920-0x923 on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 pcib0: <ACPI Host-PCI bridge> on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <display, VGA> at device 3.0 (no driver attached) pci0: <base peripheral> at device 4.0 (no driver attached) pci0: <base peripheral> at device 4.2 (no driver attached) isab0: <PCI-ISA bridge> at device 15.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <ServerWorks CSB5 UDMA100 controller> port 0x2000-0x200f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 pci0: <serial bus, USB> at device 15.2 (no driver attached) pcib1: <ACPI Host-PCI bridge> on acpi0 pci1: <ACPI PCI bus> on pcib1 ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem 0xf7cf0000-0xf7cf3fff,0xf7dc0000-0xf7dfffff irq 30 at device 3.0 on pci1 ciss0: [GIANT-LOCKED] pcib2: <ACPI Host-PCI bridge> on acpi0 pci2: <ACPI PCI bus> on pcib2 bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf7ef0000-0xf7efffff irq 29 at device 1.0 on pci2 bge0: failed to allocate DMA resources device_attach: bge0 attach returned 6 bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf7ee0000-0xf7eeffff irq 31 at device 2.0 on pci2 bge1: failed to allocate DMA resources device_attach: bge1 attach returned 6 pcib3: <ACPI Host-PCI bridge> on acpi0 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI Host-PCI bridge> on acpi0 pci6: <ACPI PCI bus> on pcib4 pci6: <base peripheral> at device 30.0 (no driver attached) atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface orm0: <ISA Option ROMs> at iomem 0xee000-0xeffff,0xcc000-0xcd7ff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec ATAPI_RESET time = 30us acd0: CDROM <COMPAQ CD-ROM SN-124/N104> at ata0-master PIO4 da0 at ciss0 bus 0 target 0 lun 0 da0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device da0: 135.168MB/s transfers da0: 34727MB (71122560 512 byte sectors: 255H 32S/T 8716C) da1 at ciss0 bus 0 target 1 lun 0 da1: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device da1: 135.168MB/s transfers da1: 104183MB (213367680 512 byte sectors: 255H 32S/T 26148C) da2 at ciss0 bus 0 target 2 lun 0 da2: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device da2: 135.168MB/s transfers da2: 34727MB (71122560 512 byte sectors: 255H 32S/T 8716C) panic: vm_proc_new: upage allocation failed cpuid = 0 KDB: enter: panic [thread 0] Stopped at kdb_enter+0x2b: nop db> where kdb_enter(c0553a3d) at kdb_enter+0x2b panic(c0562f2e,0,c03adbc7,ca2670a0,3) at panic+0x127 vm_proc_new(ca86ba80,ca2670a0,3,0,c087fc94) at vm_proc_new+0x30 proc_init(ca86ba80,1c0,103) at proc_init+0x1d slab_zalloc(c0a232c0,103,7,ca386fc0,c0a20098) at slab_zalloc+0x331 uma_zone_slab(c0a232c0,3,2,10,18) at uma_zone_slab+0xd0 uma_zalloc_bucket(c0a232c0,3) at uma_zalloc_bucket+0x15c uma_zalloc_arg(c0a232c0,0,2) at uma_zalloc_arg+0x27a fork1(c05d8000,20034,0,c087fd50) at fork1+0x31f kthread_create(c04cfd0c,0,c05f0df8,0,0,c0534b94,c0564107) at kthread_create+0x3d kproc_start(c05c5c00,878020,878000,0,c0240ede) at kproc_start+0x1f mi_startup() at mi_startup+0x96 begin() at begin+0x2c db>Received on Wed Sep 22 2004 - 17:20:56 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:13 UTC