I see the ahd0 message below on just about every boot of a dell sc1425 running 6.0-BETA2, just after "waiting for scsi devices to settle". Once the system is up I don't see it again. Is it harmful? Can I help? The machine has a serial cable attached so it can be peeked and poked if need be. Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-BETA2 #1: Tue Aug 2 23:04:26 EST 2005 sam_at_gis2.newcastle.edu.au:/usr/obj/usr/src/sys/GIS2 WARNING: WITNESS option enabled, expect reduced performance. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2800.11-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf41 Stepping = 1 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x641d<SSE3,RSVD2,MON,DS_CPL,CNTX-ID,CX16,<b14>> AMD Features=0x20100000<NX,LM> Hyperthreading: 2 logical CPUs real memory = 1073479680 (1023 MB) avail memory = 1041424384 (993 MB) ACPI APIC Table: <DELL PESC1425> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 6 cpu3 (AP): APIC ID: 7 ioapic0: Changing APIC ID to 8 ioapic1: Changing APIC ID to 9 ioapic1: WARNING: intbase 32 != expected base 24 ioapic2: Changing APIC ID to 10 ioapic2: WARNING: intbase 64 != expected base 56 ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 32-55 on motherboard ioapic2 <Version 2.0> irqs 64-87 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL PESC1425> on motherboard acpi0: Power Button (fixed) pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0 pci_link1: <ACPI PCI Link LNKB> irq 11 on acpi0 pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0 pci_link3: <ACPI PCI Link LNKD> irq 10 on acpi0 pci_link4: <ACPI PCI Link LNKE> irq 3 on acpi0 pci_link5: <ACPI PCI Link LNKF> on acpi0 pci_link6: <ACPI PCI Link LNKG> on acpi0 pci_link7: <ACPI PCI Link LNKH> irq 6 on acpi0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1 pci2: <ACPI PCI bus> on pcib2 em0: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port 0xecc0-0xecff mem 0xdfde0000-0xdfdfffff irq 32 at device 4.0 on pci2 em0: Ethernet address: 00:14:22:09:27:67 em0: Speed:N/A Duplex:N/A pci1: <base peripheral, interrupt controller> at device 0.1 (no driver attached) pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci1 pci3: <ACPI PCI bus> on pcib3 ahd0: <Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter> port 0xdc00-0xdcff,0xd800-0xd8ff mem 0xdfbfe000-0xdfbfffff irq 66 at device 7.0 on pci3 ahd0: [GIANT-LOCKED] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs ahd1: <Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter> port 0xd400-0xd4ff,0xd000-0xd0ff mem 0xdfbfc000-0xdfbfdfff irq 67 at device 7.1 on pci3 ahd1: [GIANT-LOCKED] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs pci1: <base peripheral, interrupt controller> at device 0.3 (no driver attached) uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xace0-0xacff irq 16 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xacc0-0xacdf irq 19 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdff00000-0xdff003ff irq 23 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <EHCI (generic) USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 4 ports with 4 removable, self powered pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci4: <ACPI PCI bus> on pcib4 em1: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port 0xbcc0-0xbcff mem 0xdf7e0000-0xdf7fffff irq 20 at device 3.0 on pci4 em1: Ethernet address: 00:14:22:09:27:68 em1: Speed:N/A Duplex:N/A pci4: <display, VGA> at device 13.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH5 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A, console pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xcbfff,0xd6000-0xd6fff,0xec000-0xeffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 1.000 msec Waiting 5 seconds for SCSI devices to settle acd0: CDROM <TEAC CD-ROM CD-224E/K.9A> at ata0-master UDMA33 ahd0: Invalid Sequencer interrupt occurred. >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<< ahd0: Dumping Card State at program address 0x23b Mode 0x0 Card was paused INTSTAT[0x0] SELOID[0x1] SELID[0x0] HS_MAILBOX[0x0] INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11] DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE) SCSISIGI[0x0]:(P_DATAOUT) SCSIPHASE[0x0] SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE) SCSISEQ0[0x0] SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) SEQCTL0[0x0] SEQINTCTL[0x6]:(INTMASK1|INTMASK2) SEQ_FLAGS[0x0] SEQ_FLAGS2[0x0] QFREEZE_COUNT[0x2] KERNEL_QFREEZE_COUNT[0x2] MK_MESSAGE_SCB[0xff00] MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0] LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x0] SCB Count = 16 CMDS_PENDING = 0 LASTSCB 0xffff CURRSCB 0xe NEXTSCB 0xff40 qinstart = 28 qinfifonext = 28 QINFIFO: WAITING_TID_QUEUES: Pending list: Total 0 Kernel Free SCB list: 15 14 1 2 3 4 5 6 7 8 9 10 11 12 13 0 Sequencer Complete DMA-inprog list: Sequencer Complete list: Sequencer DMA-Up and Complete list: Sequencer On QFreeze and Complete list: ahd0: FIFO0 Free, LONGJMP == 0x8000, SCB 0xf SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) ahd0: FIFO1 Free, LONGJMP == 0x8063, SCB 0xe SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) LQIN: 0x8 0x0 0x0 0xf 0x0 0x1 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 ahd0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x42 ahd0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1 ahd0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0 SIMODE0[0xc]:(ENOVERRUN|ENIOERR) CCSCBCTL[0x4]:(CCSCBDIR) ahd0: REG0 == 0x8b60, SINDEX = 0x10e, DINDEX = 0x104 ahd0: SCBPTR == 0xf, SCB_NEXT == 0xff40, SCB_NEXT2 == 0xff3b CDB 12 20 0 80 88 36 STACK: 0x236 0x2 0x0 0x0 0x0 0x0 0x0 0x0 <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>> Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0 Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0 da0 at ahd0 bus 0 target 0 lun 0 da0: <SEAGATE ST373207LW D702> Fixed Direct Access SCSI-3 device da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da0: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C) da1 at ahd0 bus 0 target 1 lun 0 da1: <SEAGATE ST373207LW D702> Fixed Direct Access SCSI-3 device da1: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da1: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C) ATA PseudoRAID loaded SMP: AP CPU #2 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #3 Launched! Trying to mount root from ufs:/dev/da0s1a -- Sam Lawrance lawrance_at_FreeBSD.org ph +61 0425 228 579 boris_at_brooknet.com.auReceived on Mon Aug 08 2005 - 20:50:22 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:40 UTC