Hi again. Actually setting hw.syscons.sc_no_suspend_vtswitch=1 seems to make resume not work. hw.acpi.reset_video=0 is the only needed value. Then it's all fine. The strange thing is setting hw.syscons.sc_no_suspend_vtswitch=1 manually with sysctl after the system has booted does not seem to have any effect. It only disables proper functionality of resume after reboot. Cheers, Marcin. On Thu, 9 Jun 2005 00:23:24 +0200 Marcin Jessa <lists_at_yazzy.org> wrote: > Hi Kevin, guys. > > Thanks a lot, that helped! > Everything comes back after resume without any problem. > Network (iwi and fx drivers), USB... > Even X is fine and I do not need to switch to console to bring it back. > I tried suspend/resume 3 times and it worked like a charm each and every time. > > I added acpi_video_load="YES" to loader.conf > and > hw.acpi.reset_video=0 > hw.syscons.sc_no_suspend_vtswitch=1 > to sysctl.conf > > I noticed after resume dmesg spits out: > > acpi: suspend request ignored (not ready yet) > wakeup from sleeping state (slept 00:00:19) > > Now even powerd works great automatically adjusting the speed of my CPU when idle on battery. > > The only thing that does not work properly is when hw.acpi.lid_switch_state=S3. > It goes to sleep mode when I close the lid but X restarts after resume. I can live with that tho. > > > Thanks again Kevin, you made my day! > > > > On Wed, 08 Jun 2005 14:47:26 -0700 > "Kevin Oberman" <oberman_at_es.net> wrote: > > > > Date: Wed, 8 Jun 2005 23:17:40 +0200 > > > From: Marcin Jessa <lists_at_yazzy.org> > > > Sender: owner-freebsd-mobile_at_freebsd.org > > > > > > Hi. > > > > > > I've Thinkpad R50e and I am struggeling to make resume work on it. > > > I'm on FreeBSD 6.0-CURRENT #2: Wed Jun 8 21:12:11 CEST 2005 (built on sources from a couple of hours ago). > > > I am able to change the speed of CPU and put the laptop in sleep mode with acpiconf -s 3 (S1, S2 and S3 are supported). > > > The problem is it never manages to fully wake up from the sleep mode. > > > I tried with and without X running with the same result. > > > It wakes up, I can hear the drives spin, the screen is turned on but the laptop is still frozen. > > > The keayboard is unaccessible. > > > I dont have apm enabled in the kernel. > > > Those are the values in my sysctl.conf: > > > hw.pci.do_powerstate=1 > > > hw.acpi.lid_switch_state=S3 > > > hw.acpi.standby_state=S1 > > > hw.acpi.suspend_state=S3 > > > hw.acpi.sleep_button_state=S3 > > > vfs.usermount=1 > > > hw.acpi.sleep_delay=3 > > > > > > device.hints has hint.apm.0.disabled="0" > > > > > > In the dmesg I can also see many occurances of > > > ichss0: transition to 1 failed > > > I think that begun after I added device cpufreq to my kernel config. > > > > > > I also followed http://www.iosn.net/Members/kaeru/articles/freebsd/x40/index_html but with no luck. > > > > > > Any ideas how to make resume work? > > > > Just some suggestions that might (or might not) help. > > > > Play with hw.acpi.reset_video and hw.syscons.sc_no_suspend_vtswitch. You > > may find that you need the jhb acpi_video_dpms patch. > > > > I have the following /boot/loader.conf on my T30: > > cpufreq_load="YES" > > vesa_load="YES" > > snd_ich_load="YES" > > acpi_video_load="YES" > > acpi_ibm_load="YES" (This is NOT required for resume, but it is nice for > > a few things. It is the recently posted test > > version and I don't think it's been committed.) > > > > I have the following in my /etc/sysctl.conf on my T30: > > hw.acpi.reset_video=0 > > hw.syscons.sc_no_suspend_vtswitch=1 > > hw.acpi.lid_switch_state=NONE > > hw.pci.do_powerstate=1 > > > > I do notice that I need to switch from my X display to a vty and back > > after a resume to get the display back. (CTRL-ALT-F1, ALT-F9) > > The SpeedStep errors are troubling. I have not seen any other reports of > > this. > > -- > > R. Kevin Oberman, Network Engineer > > Energy Sciences Network (ESnet) > > Ernest O. Lawrence Berkeley National Laboratory (Berkeley Lab) > > E-mail: oberman_at_es.net Phone: +1 510 486-8634 > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"Received on Wed Jun 08 2005 - 21:23:37 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:36 UTC