Re: Loss of ed(4) in a RC1 booted in qemu

From: Luigi Rizzo <rizzo_at_icir.org>
Date: Thu, 13 Oct 2005 16:00:14 -0700
On Thu, Oct 13, 2005 at 04:36:47PM -0600, M. Warner Losh wrote:
...
> I've committed changes to -current to work on patched and unpatched
> versions of qemu.  Here's my patches to qemu to implement the RTL8029
> specific registers.  Place them in files/patch-hw::ne2000.c of the
> emulators/qemu port.
> 
> Warner

> --- hw/ne2000.c~	Thu Oct 13 16:33:39 2005
> +++ hw/ne2000.c	Thu Oct 13 16:33:47 2005
probably need to add qemu/ in front of the filename because
patch is invoked wiht -p1 ...

	cheers
	luigi

> _at__at_ -47,7 +47,9 _at__at_
>  #define EN0_CRDAHI	0x09	/* high byte, current remote dma address RD */
>  #define EN0_RSARHI	0x09	/* Remote start address reg 1 */
>  #define EN0_RCNTLO	0x0a	/* Remote byte count reg WR */
> +#define EN0_RTL8029ID0	0x0a	/* Realtek ID byte #1 RD */
>  #define EN0_RCNTHI	0x0b	/* Remote byte count reg WR */
> +#define EN0_RTL8029ID1	0x0b	/* Realtek ID byte #2 RD */
>  #define EN0_RSR		0x0c	/* rx status reg RD */
>  #define EN0_RXCR	0x0c	/* RX configuration reg WR */
>  #define EN0_TXCR	0x0d	/* TX configuration reg WR */
> _at__at_ -64,6 +66,11 _at__at_
>  #define EN2_STARTPG	0x21	/* Starting page of ring bfr RD */
>  #define EN2_STOPPG	0x22	/* Ending page +1 of ring bfr RD */
>  
> +#define EN3_CONFIG0	0x33
> +#define EN3_CONFIG1	0x34
> +#define EN3_CONFIG2	0x35
> +#define EN3_CONFIG3	0x36
> +
>  /*  Register accessed at EN_CMD, the 8390 base addr.  */
>  #define E8390_STOP	0x01	/* Stop and reset the chip */
>  #define E8390_START	0x02	/* Start the chip, clear reset */
> _at__at_ -385,6 +392,21 _at__at_
>          case EN2_STOPPG:
>              ret = s->stop >> 8;
>              break;
> +	case EN0_RTL8029ID0:
> +	    ret = 0x50;
> +	    break;
> +	case EN0_RTL8029ID1:
> +	    ret = 0x43;
> +	    break;
> +	case EN3_CONFIG0:
> +	    ret = 0;		/* 10baseT media */
> +	    break;
> +	case EN3_CONFIG2:
> +	    ret = 0x40;		/* 10baseT active */
> +	    break;
> +	case EN3_CONFIG3:
> +	    ret = 0x40;		/* Full duplex */
> +	    break;
>          default:
>              ret = 0x00;
>              break;

> _______________________________________________
> freebsd-current_at_freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"
Received on Thu Oct 13 2005 - 21:00:27 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:45 UTC