RC1 panic on boot

From: Andrew Thompson <thompsa_at_freebsd.org>
Date: Sat, 15 Oct 2005 14:43:13 +1300
Hi,


I am getting this panic on RC1, I am booting disc1 to install the
system. Its a HP Omnibook 4150 and no PC cards are inserted. 

It has 5.4 on the drive at the moment which installed fine. I have
attached a couple of dmesg logs.


Andrew


Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RC1 #0: Sun Oct  9 20:32:57 UTC 2005
    root_at_x64.samsco.home:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Celeron (448.05-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x681  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 536870912 (512 MB)
avail memory = 511746048 (488 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <HP-MCD CK RSDT> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 10 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 10 on acpi0
pci_link2: <ACPI PCI Link LNKD> irq 10 on acpi0
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
acpi_ec0: <Embedded Controller: GPE 0x9> port 0x62,0x66 on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0


Fatal trap 12: page fault while in kernel mode
fault virtual address   = 0x0
fault code              = supervisor read, page not present
instruction pointer     = 0x20:0xc0e96b0a
stack pointer           = 0x28:0xc1020b7c
frame pointer           = 0x28:0xc1020b8c
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, def32 1, gran 1
processor eflags        = interrupt enabled, resume, IOPL = 0
current process         = 0 (swapper)
trap number             = 12
panic: page fault
Uptime: 1s


Received on Fri Oct 14 2005 - 23:43:17 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:45 UTC