On 17 Oct 2005 at 7:07, Scott Long wrote: > Dan Langille wrote: > > On 17 Oct 2005 at 7:05, Mike Tancsa wrote: > > > > > >>At 06:54 AM 17/10/2005, Dan Langille wrote: > >> > >>>Anyone running RAID on 6.0-RC1, specifically twed? > >> > >>Yes. > >>% uname -a > >>FreeBSD tor1-o.sentex.ca 6.0-RC1 FreeBSD 6.0-RC1 #0: Wed Oct 12 > >>10:08:51 EDT > >>2005 mdtancsa_at_tor1-o.sentex.ca:/usr/obj/usr/src/sys/global i386 > >> > >>% df > >>Filesystem 1K-blocks Used Avail Capacity Mounted on > >>/dev/twed0s1a 1012974 63220 868718 7% / > >>devfs 1 1 0 100% /dev > >>/dev/twed0s1e 10154158 694842 8646984 7% /home > >>/dev/twed0s1f 20308398 4 18683724 0% /securestorage > >>/dev/twed0s1g 2026030 6000 1857948 0% /tmp > >>/dev/twed0s1d 20308398 2645286 16038442 14% /usr > >>/dev/twed0s1h 19831118 499396 17745234 3% /var > >>devfs 1 1 0 100% /var/named/dev > >> > >> > >> > >>>When booting from the 6.0-RC1 install CD, I'm getting twed0 found on > >>>probing. The results look right. But then the install freezes (I > >>>waited an hour). I have a screen shot which produced with a boot -v: > >> > >>Where does it get stuck when doing a boot -v > > > > > > See this screen shot: > > > > <http://www.langille.org/tmp/6.0RC1-twed.jpg> > > > > BTW: Since composing that message, I tried "unset acpi_load". That > > gets me into the installer. That's when using the twed. I haven't > > tried the Promise with the unset yet. > > Likely an interrupt routing problem. More information on your > motherboard, as well as a real console log during boot, is needed > to say anything else. The motherboard is an ASUS A8V DEluce, with ACPI BIOS Revision 1009. The AMIBIOS is version 08.00.09 dated 12/22/04. It's running an AMD Ahtlon 64 3000+ at 1800MHz. Here's the real console log, ignore my mistaken loader.conf entry. /boot.config: -DhConsoles: internal video/keyboard serial port BIOS drive A: is disk0 BIOS drive C: is disk1 BIOS 639kB/1047232kB available memory FreeBSD/i386 bootstrap loader, Revision 1.1 (root_at_x64.samsco.home, Sun Oct 9 18:32:30 UTC 2005) Loading /boot/defaults/loader.conf Warning: syntax error on file /boot/loader.conf unset acpi_load ^ /boot/kernel/kernel text=0x487f94 data=0x803e0+0x4ce28 syms=[0x4+0x614a0+0x4+0x77f33] Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel] in 8 seconds... Type '?' for a list of commands, 'help' for more detailed help. OK boot -v /boot/kernel/acpi.ko text=0x40c0c data=0x2160+0x1090 syms=[0x4+0x7810+0x4+0xa292] SMAP type=01 base=0000000000000000 len=000000000009fc00 SMAP type=02 base=000000000009fc00 len=0000000000000400 SMAP type=02 base=00000000000e4000 len=000000000001c000 SMAP type=01 base=0000000000100000 len=000000003feb0000 SMAP type=03 base=000000003ffb0000 len=0000000000010000 SMAP type=04 base=000000003ffc0000 len=0000000000030000 SMAP type=02 base=000000003fff0000 len=0000000000010000 SMAP type=02 base=00000000ff780000 len=0000000000880000 Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-RC1 #0: Sun Oct 9 20:32:57 UTC 2005 root_at_x64.samsco.home:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a88000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a88180. MP Configuration Table version 1.1 found at 0xc00f1080 Table 'FACP' at 0x3ffb0200 Table 'OEMB' at 0x3ffc0040 MADT: No MADT table found APIC: Using the MPTable enumerator. MPTable: <ASUSTeK Deluxe > Calibrating clock(s) ... i8254 clock: 1193239 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1802311343 Hz CPU: AMD Athlon(tm) 64 Processor 3000+ (1802.31-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x10ff0 Stepping = 0 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG E,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD Features=0xe2500800<SYSCALL,NX,MMX+,<b25>,LM,3DNow+,3DNow> Data TLB: 32 entries, fully associative Instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative real memory = 1073414144 (1023 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c25000 - 0x000000003ed78fff, 1041580032 bytes (254292 pages) avail memory = 1041522688 (993 MB) bios32: Found BIOS32 Service Directory header at 0xc00f0000 bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0x31 pnpbios: Found PnP BIOS data at 0xc00f5bd0 pnpbios: Entry = f0000:693a Rev = 1.0 Other BIOS signatures found: ioapic0: Assuming intbase of 0 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) ioapic0: intpin 1 bus ISA ioapic0: intpin 1 trigger: edge ioapic0: intpin 1 polarity: high ioapic0: intpin 2 bus ISA ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high ioapic0: intpin 3 bus ISA ioapic0: intpin 3 trigger: edge ioapic0: intpin 3 polarity: high ioapic0: intpin 4 bus ISA ioapic0: intpin 4 trigger: edge ioapic0: intpin 4 polarity: high ioapic0: intpin 5 bus ISA ioapic0: intpin 5 trigger: level ioapic0: intpin 5 polarity: high ioapic0: intpin 6 bus ISA ioapic0: intpin 6 trigger: edge ioapic0: intpin 6 polarity: high ioapic0: intpin 7 bus ISA ioapic0: intpin 7 trigger: edge ioapic0: intpin 7 polarity: high ioapic0: intpin 8 bus ISA ioapic0: intpin 8 trigger: edge ioapic0: intpin 8 polarity: high ioapic0: intpin 9 bus ISA ioapic0: intpin 9 trigger: edge ioapic0: intpin 9 polarity: high ioapic0: intpin 10 bus ISA ioapic0: intpin 10 trigger: level ioapic0: intpin 10 polarity: high ioapic0: intpin 11 bus ISA ioapic0: intpin 11 trigger: level ioapic0: intpin 11 polarity: high ioapic0: intpin 12 bus ISA ioapic0: intpin 12 trigger: edge ioapic0: intpin 12 polarity: high ioapic0: intpin 13 bus ISA ioapic0: intpin 13 trigger: edge ioapic0: intpin 13 polarity: high ioapic0: intpin 14 bus ISA ioapic0: intpin 14 trigger: edge ioapic0: intpin 14 polarity: high ioapic0: intpin 15 bus ISA ioapic0: intpin 15 trigger: edge ioapic0: intpin 15 polarity: high ioapic0: intpin 20 bus PCI ioapic0: intpin 20 trigger: level ioapic0: intpin 20 polarity: low ioapic0: intpin 20 bus PCI ioapic0: intpin 20 trigger: level ioapic0: intpin 20 polarity: low ioapic0: intpin 17 bus PCI ioapic0: intpin 17 trigger: level ioapic0: intpin 17 polarity: low ioapic0: intpin 18 bus PCI ioapic0: intpin 18 trigger: level ioapic0: intpin 18 polarity: low ioapic0: intpin 19 bus PCI ioapic0: intpin 19 trigger: level ioapic0: intpin 19 polarity: low lapic: Routing ExtINT -> LINT0 lapic: Routing NMI -> LINT1 ioapic0 <Version 0.3> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00000000 err: 0x0001000f pcm: 0x00010000 wlan: <802.11 Link Layer> random: <entropy source, Software, Yarrow> nfslock: pseudo-device io: <I/O> mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <A M I OEMRSDT> on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x8000083c pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=02821106) pcibios: BIOS version 2.10 Found $PIR table, 12 entries at 0xc00f5a80 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 1 A 0x01 3 4 5 7 10 11 14 15 embedded 0 1 B 0x02 3 4 5 7 10 11 14 15 embedded 0 17 C 0x03 3 4 5 7 10 11 14 15 embedded 0 15 A 0x01 3 4 5 7 10 11 14 15 embedded 0 15 B 0x02 3 4 5 7 10 11 14 15 embedded 0 15 C 0x03 3 4 5 7 10 11 14 15 embedded 0 15 D 0x05 3 4 5 7 10 11 14 15 embedded 0 16 A 0x01 3 4 5 7 10 11 14 15 embedded 0 16 B 0x02 3 4 5 7 10 11 14 15 embedded 0 16 C 0x03 3 4 5 7 10 11 14 15 embedded 0 16 D 0x05 3 4 5 7 10 11 14 15 slot 1 0 11 A 0x01 3 4 5 7 10 11 14 15 slot 1 0 11 B 0x02 3 4 5 7 10 11 14 15 slot 1 0 11 C 0x03 3 4 5 7 10 11 14 15 slot 1 0 11 D 0x05 3 4 5 7 10 11 14 15 slot 2 0 12 A 0x02 3 4 5 7 10 11 14 15 slot 2 0 12 B 0x03 3 4 5 7 10 11 14 15 slot 2 0 12 C 0x05 3 4 5 7 10 11 14 15 slot 2 0 12 D 0x01 3 4 5 7 10 11 14 15 slot 3 0 13 A 0x03 3 4 5 7 10 11 14 15 slot 3 0 13 B 0x05 3 4 5 7 10 11 14 15 slot 3 0 13 C 0x01 3 4 5 7 10 11 14 15 slot 3 0 13 D 0x02 3 4 5 7 10 11 14 15 slot 4 0 14 A 0x05 3 4 5 7 10 11 14 15 slot 4 0 14 B 0x01 3 4 5 7 10 11 14 15 slot 4 0 14 C 0x02 3 4 5 7 10 11 14 15 slot 4 0 14 D 0x03 3 4 5 7 10 11 14 15 slot 5 0 9 A 0x01 3 4 5 7 10 11 14 15 slot 5 0 9 B 0x02 3 4 5 7 10 11 14 15 slot 5 0 9 C 0x03 3 4 5 7 10 11 14 15 slot 5 0 9 D 0x05 3 4 5 7 10 11 14 15 embedded 0 7 A 0x01 3 4 5 7 10 11 14 15 embedded 0 10 A 0x02 3 4 5 7 10 11 14 15 embedded 0 8 A 0x03 3 4 5 7 10 11 14 15 AcpiOsDerivePciId: bus 0 dev 17 func 0 AcpiOsDerivePciId: bus 0 dev 17 func 0 acpi0: Power Button (fixed) ioapic0: Changing trigger for pin 9 to level ioapic0: Changing polarity for pin 9 to low pci_link0: <ACPI PCI Link LNKA> irq 0 on acpi0 pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link1: <ACPI PCI Link LNKB> irq 10 on acpi0 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 7 10 11 14 15 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 7 10 11 14 15 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 5 N 0 3 4 5 7 10 11 14 15 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 5 N 0 3 4 5 7 10 11 14 15 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link3: <ACPI PCI Link LNKD> irq 11 on acpi0 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 7 10 11 14 15 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 7 10 11 14 15 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0 pci_link4: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link4: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link4: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link5: <ACPI PCI Link LNKF> irq 0 on acpi0 pci_link5: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link5: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link5: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link6: <ACPI PCI Link LNKG> irq 0 on acpi0 pci_link6: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link6: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link6: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link7: <ACPI PCI Link LNKH> irq 0 on acpi0 pci_link7: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link7: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 pci_link7: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 7 10 11 14 15 ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x1106, dev=0x0282, revid=0x00 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x2230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 3, range 32, base f0000000, size 26, enabled found-> vendor=0x1106, dev=0x1282, revid=0x00 bus=0, slot=0, func=1 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1106, dev=0x2282, revid=0x00 bus=0, slot=0, func=2 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1106, dev=0x3282, revid=0x00 bus=0, slot=0, func=3 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1106, dev=0x4282, revid=0x00 bus=0, slot=0, func=4 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1106, dev=0x7282, revid=0x00 bus=0, slot=0, func=7 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1106, dev=0xb188, revid=0x00 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x1229, revid=0x08 bus=0, slot=12, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fbb00000, size 12, enabled map[14]: type 4, range 32, base 0000c400, size 6, enabled map[18]: type 1, range 32, base fba00000, size 20, enabled pcib0: matched entry for 0.12.INTA (src \_SB_.LNKB:0) ioapic0: Changing polarity for pin 10 to low pcib0: slot 12 INTA routed to irq 10 via \_SB_.LNKB found-> vendor=0x13c1, dev=0x1001, revid=0x01 bus=0, slot=13, func=0 class=01-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x011f, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x09 (2250 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 1 supports D0 D1 D3 current D0 map[10]: type 4, range 32, base 0000c800, size 4, enabled map[18]: type 1, range 32, base fb000000, size 23, enabled pcib0: matched entry for 0.13.INTA (src \_SB_.LNKC:0) ioapic0: Changing polarity for pin 5 to low pcib0: slot 13 INTA routed to irq 5 via \_SB_.LNKC found-> vendor=0x5333, dev=0x8901, revid=0x16 bus=0, slot=14, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[10]: type 1, range 32, base f4000000, size 26, enabled pcib0: matched entry for 0.14.INTA (src \_SB_.LNKD:0) ioapic0: Changing polarity for pin 11 to low pcib0: slot 14 INTA routed to irq 11 via \_SB_.LNKD found-> vendor=0x1106, dev=0x3149, revid=0x80 bus=0, slot=15, func=0 class=01-04-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000e800, size 3, enabled map[14]: type 4, range 32, base 0000e400, size 2, enabled map[18]: type 4, range 32, base 0000e000, size 3, enabled map[1c]: type 4, range 32, base 0000d800, size 2, enabled map[20]: type 4, range 32, base 0000d400, size 4, enabled map[24]: type 4, range 32, base 0000d000, size 8, enabled pcib0: matched entry for 0.15.INTB (src \_SB_.LNKB:0) pcib0: slot 15 INTB routed to irq 10 via \_SB_.LNKB found-> vendor=0x1106, dev=0x0571, revid=0x06 bus=0, slot=15, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 map[20]: type 4, range 32, base 0000fc00, size 4, enabled found-> vendor=0x1106, dev=0x3227, revid=0x00 bus=0, slot=17, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 found-> vendor=0x1022, dev=0x1100, revid=0x00 bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) agp0: <VIA K8T800Pro host to PCI bridge> mem 0xf0000000-0xf3ffffff at device 0.0 on pci0 AMD64: 1 Misc. Control unit(s) found. agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf0000000 agp0: allocating GATT for aperture of size 64M pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x0-0x0 pcib1: memory decode 0xfff00000-0xfffff pcib1: prefetched decode 0xfff00000-0xfffff pcib1: could not get PCI interrupt routing table for \_SB_.PCI0.P0P1 - AE_NOT_FOUND pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 fxp0: <Intel 82559 Pro/100 Ethernet> port 0xc400-0xc43f mem 0xfbb00000-0xfbb00fff,0xfba00000-0xfbafffff irq 10 at device 12.0 on pci0 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfbb00000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1229 1014 105c 0008 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:04:ac:a3:70:3d fxp0: [MPSAFE] twe0: <3ware Storage Controller. Driver version 1.50.01.002> port 0xc800-0xc80f mem 0xfb000000-0xfb7fffff irq 5 at device 13.0 on pci0 twe0: Reserved 0x10 bytes for rid 0x10 type 4 at 0xc800 twe0: [GIANT-LOCKED] twe0: AEN: <soft reset> twe0: 2 ports, Firmware FE7X 1.05.00.063, BIOS BE7X 1.08.00.048 twe0: Monitor ME7X 1.01.00.038, PCB Rev4 , Achip 3.20 , Pchip 1.30-66 twe0: port 0: Maxtor 6Y080L0 78167MB twe0: port 1: ST380011A 76319MB pci0: <display, VGA> at device 14.0 (no driver attached) atapci0: <VIA 6420 SATA150 controller> port 0xe800-0xe807,0xe400- 0xe403,0xe000-0xe007,0xd800-0xd803,0xd400-0xd40f,0xd000-0xd0ff irq 10 at device 15.0 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xd400 atapci0: [MPSAFE] atapci0: Reserved 0x100 bytes for rid 0x24 type 4 at 0xd000 ata2: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xe800 atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xe400 ata2: SATA connect status=00000000 ata2: [MPSAFE] ata3: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xe000 atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xd800 ata3: SATA connect status=00000000 ata3: [MPSAFE] atapci1: <VIA 8237 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170- 0x177,0x376,0xfc00-0xfc0f at device 15.1 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfc00 ata0: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=60 ostat1=70 ata0: stat0=0x20 err=0x20 lsb=0x20 msb=0x20 ata0: stat1=0x30 err=0x30 lsb=0x30 msb=0x30 ata0: reset tp2 stat0=20 stat1=30 devices=0x0 ata0: [MPSAFE] ata1: <ATA channel 1> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=60 ostat1=50 ata1: stat0=0x20 err=0x20 lsb=0x20 msb=0x20 ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb ata1: reset tp2 stat0=20 stat1=00 devices=0x8<ATAPI_SLAVE> ata1: [MPSAFE] isab0: <PCI-ISA bridge> at device 17.0 on pci0 isa0: <ISA bus> on isab0 acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 80 fdc0: [MPSAFE] fdc0: [FAST] sio0: irq maps: 0x8001 0x8009 0x8001 0x8001 sio0: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 on acpi0 sio0: type 16550A, console sio1: irq maps: 0x8001 0x8011 0x8001 0x8001 sio1: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 sio1: type 16550A ex_isa_identify() ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered lapic: Divisor 2, Frequency 100128250 hz Timecounter "TSC" frequency 1802311343 Hz quality 800 Timecounters tick every 1.000 msec lo0: bpf attached ata1-slave: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire acd0: setting PIO4 on VIA 8237 chip acd0: <HL-DT-ST CD-ROM GCR-8520B/1.00> CDROM drive at ata1 as slave acd0: read 8937KB/s (8937KB/s), 128KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked, lock protected acd0: Medium: no/blank disc twed0: <Unit 0, TwinStor, Normal> on twe0 twed0: 76318MB (156299440 sectors) ATA PseudoRAID loaded ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0 ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0 ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0 ioapic0: routing intpin 5 (ISA IRQ 5) to cluster 0 ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0 ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0 ioapic0: routing intpin 10 (ISA IRQ 10) to cluster 0 ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0 ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0 ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0 GEOM: new disk twed0 -- Dan Langille : http://www.langille.org/ BSDCan - The Technical BSD Conference - http://www.bsdcan.org/Received on Mon Oct 17 2005 - 19:51:37 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:45 UTC
