Patrick Bowen wrote: > Just upgraded from 6.1 RELEASE to -current, and a previously working > D-Link DWL-G630 AirPlus G wireless notebook adapter no longer works. > > H/W ver.: C2 F/W ver.: 3.01 > > This from dmesg; > > cbb alloc res fail > cbb alloc res fail > cardbus0: <network, ethernet> at device 0.0 (no driver attached) > > and this from dumpcis on Linux; > > Socket 0: > manfid 0x0271, 0x0012 > config_cb base 0x0000 last_index 0x01 > cftable_entry_cb 0x01 [default] > [master] [parity] [serr] [fast back] > Vcc Vnom 3300mV Istatic 25mA Iavg 450mA Ipeak 500mA > irq mask 0xffff [level] > mem_base 1 > BAR 1 size 64kb [mem] > vers_1 7.1, "Atheros Communications, Inc.", "AR5001-0000-0000", > "Wireless LAN Reference Card", "00" > funcid network_adapter [post] > lan_speed 6 mb/sec > lan_speed 9 mb/sec > lan_speed 12 mb/sec > lan_speed 18 mb/sec > lan_speed 24 mb/sec > lan_speed 36 mb/sec > lan_speed 48 mb/sec > lan_speed 54 mb/sec > lan_speed 72 mb/sec > lan_media 5.4_GHz > lan_node_id 00 03 2f 55 55 55 > lan_connector Closed connector standard > > Ialso snagged this from Linux's dmesg; > > [17179589.744000] pccard: CardBus card inserted into slot 0 > [17179589.776000] ath_hal: module license 'Proprietary' taints kernel. > [17179589.776000] ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, > RF5112, RF2 > 413) > [17179589.796000] cs: IO port probe 0x100-0x3af: clean. > [17179589.800000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 > [17179589.800000] cs: IO port probe 0x820-0x8ff: clean. > [17179589.800000] cs: IO port probe 0xc00-0xcf7: clean. > [17179589.800000] cs: IO port probe 0xa00-0xaff: clean. > [17179589.824000] wlan: 0.8.6.0 (EXPERIMENTAL) > [17179589.824000] ath_rate_sample: 1.2 > [17179589.832000] ath_pci: 0.9.6.0 (EXPERIMENTAL) > [17179589.832000] PCI: Enabling device 0000:07:00.0 (0000 -> 0002) > [17179589.832000] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 > (level, low) -> > IRQ 177 > [17179590.416000] Build date: Jul 10 2006 > [17179590.416000] Debugging version (IEEE80211) > [17179590.416000] ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > [17179590.416000] ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps > 9Mbps 12Mbps > 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > [17179590.416000] ath0: H/W encryption support: WEP AES AES_CCM TKIP > [17179590.416000] ath0: mac 7.8 phy 4.5 radio 5.6 > [17179590.416000] ath0: Use hw queue 1 for WME_AC_BE traffic > [17179590.416000] ath0: Use hw queue 0 for WME_AC_BK traffic > [17179590.416000] ath0: Use hw queue 2 for WME_AC_VI traffic > [17179590.416000] ath0: Use hw queue 3 for WME_AC_VO traffic > [17179590.416000] ath0: Use hw queue 8 for CAB traffic > [17179590.416000] ath0: Use hw queue 9 for beacons > [17179590.416000] Debugging version (ATH) > [17179590.416000] ath0: Atheros 5212: mem=0x24000000, irq=177 > > If I can provide any more info, please let me know. > > Thanks, > Patrick > > > > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to > "freebsd-current-unsubscribe_at_freebsd.org" > I put this up on the list a couple of weeks ago, and haven't seen anything come back in the way of a dialog, so I figured I'd re-post it to see if I get any nibbles. The only thing I have to add is the following from a verbose dmesg. Complete verbose dmesg attached; > map[10]: type 1, range 64, base b4000000, size 14, enabled > pcib2: (null) requested memory range 0xb4000000-0xb4003fff: good > cbb alloc res fail > map[18]: type 4, range 32, base 00003000, size 8, enabled > cbb alloc res fail > found-> vendor=0x11ab, dev=0x4351, revid=0x10 > bus=2, slot=0, func=0 > class=02-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0007, statreg=0x4010, cachelnsz=8 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=255 > powerspec 2 supports D0 D1 D2 D3 current D0 > MSI supports 2 messages, 64 bit > cardbus0: <network, ethernet> at device 0.0 (no driver attached) Thanks, Patrick AMD Features=0x100000<NX> Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries Data TLB: 4 KB Pages, 4-way set associative, 128 entries Instruction TLB: 4 MB pages, fully associative, 2 entries 2nd-level cache: 1 MB, 4-way set associative, 64-byte line size 1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size Data TLB: 4 MB Pages, 4-way set associative, 8 entries 1st-level data cache: 32 KB, 8-way set associative, 64 byte line size L2 cache: 1024 kbytes, 4-way associative, 64 bytes/line real memory = 258867200 (246 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001028000 - 0x000000000f24efff, 237137920 bytes (57895 pages) avail memory = 239394816 (228 MB) Table 'APIC' at 0xf6e9e88 MADT: Found table at 0xf6e9e88 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 0: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 1: disabled INTR: Adding local APIC 0 as a target ACPI APIC Table: <GATEWA M365 > bios32: Found BIOS32 Service Directory header at 0xc00f6810 bios32: Entry = 0xfd700 (c00fd700) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xfd700+0x244 pnpbios: Found PnP BIOS data at 0xc00f6860 pnpbios: Entry = f0000:aee2 Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 0 MADT: Found IO APIC ID 1, Interrupt 0 at 0xfec00000 ioapic0: Changing APIC ID to 1 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: high lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high MADT: Ignoring local NMI routed to ACPI CPU 1 ioapic0 <Version 2.0> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 wlan: <802.11 Link Layer> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> random: <entropy source, Software, Yarrow> nfslock: pseudo-device io: <I/O> kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Jul 29 2006 17:35:51) npx0: INT 16 interface acpi0: <GATEWA M365> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x8000f920 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25908086) pcibios: BIOS version 2.10 acpi_bus_number: root bus has no _BBN, assuming 0 acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) acpi0: wakeup code va 0xc6a74000 pa 0x9e000 acpi_bus_number: root bus has no _BBN, assuming 0 acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR AcpiOsDerivePciId: bus 0 dev 0 func 0 ACPI timer: 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x62,0x66 on acpi0 pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 11 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 11 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 11 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link4: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 11 pci_link4: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link4: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link5: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 10 pci_link5: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 10 pci_link5: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 pci_link6: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 11 pci_link6: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link6: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 11 pci_link7: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 pci_link7: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 pci_link7: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 cpu0: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 acpi_acad0: <AC Adapter> on acpi0 battery0: <ACPI Control Method Battery> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x2590, revid=0x04 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2592, revid=0x04 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0003, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base b0080000, size 19, enabled map[14]: type 4, range 32, base 00001800, size 3, enabled map[18]: type 3, range 32, base c0000000, size 28, enabled map[1c]: type 1, range 32, base b0000000, size 18, enabled pcib0: matched entry for 0.2.INTA pcib0: slot 2 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x2792, revid=0x04 bus=0, slot=2, func=1 class=03-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base 00000000, size 19, memory disabled found-> vendor=0x8086, dev=0x2660, revid=0x04 bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 pcib0: matched entry for 0.28.INTA pcib0: slot 28 INTA hardwired to IRQ 17 found-> vendor=0x8086, dev=0x2658, revid=0x04 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[20]: type 4, range 32, base 00001820, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 19 found-> vendor=0x8086, dev=0x2659, revid=0x04 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 map[20]: type 4, range 32, base 00001840, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 23 found-> vendor=0x8086, dev=0x265a, revid=0x04 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=10 map[20]: type 4, range 32, base 00001860, size 5, enabled pcib0: matched entry for 0.29.INTC pcib0: slot 29 INTC hardwired to IRQ 22 found-> vendor=0x8086, dev=0x265b, revid=0x04 bus=0, slot=29, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=10 map[20]: type 4, range 32, base 00001880, size 5, enabled pcib0: matched entry for 0.29.INTD pcib0: slot 29 INTD hardwired to IRQ 22 found-> vendor=0x8086, dev=0x265c, revid=0x04 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base b0040000, size 10, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 19 found-> vendor=0x8086, dev=0x2448, revid=0xd4 bus=0, slot=30, func=0 class=06-04-01, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x266e, revid=0x04 bus=0, slot=30, func=2 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 00001c00, size 8, enabled map[14]: type 4, range 32, base 000018c0, size 6, enabled map[18]: type 1, range 32, base b0040800, size 9, enabled map[1c]: type 1, range 32, base b0040400, size 8, enabled pcib0: matched entry for 0.30.INTA pcib0: slot 30 INTA hardwired to IRQ 21 found-> vendor=0x8086, dev=0x266d, revid=0x04 bus=0, slot=30, func=3 class=07-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 00002400, size 8, enabled map[14]: type 4, range 32, base 00002000, size 7, enabled pcib0: matched entry for 0.30.INTB pcib0: slot 30 INTB hardwired to IRQ 20 found-> vendor=0x8086, dev=0x2641, revid=0x04 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x266f, revid=0x04 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[20]: type 4, range 32, base 00001810, size 4, enabled found-> vendor=0x8086, dev=0x266a, revid=0x04 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type 4, range 32, base 000020a0, size 5, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 19 vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0xb0080000-0xb00fffff,0xc0000000-0xcfffffff,0xb0000000-0xb003ffff irq 16 at device 2.0 on pci0 agp0: <Intel 82915GM (915GM GMCH) SVGA controller> on vgapci0 vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xb0080000 vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xb0080000 vgapci0: Reserved 0x40000 bytes for rid 0x1c type 3 at 0xb0000000 agp0: detected 7932k stolen memory agp0: aperture size is 256M vgapci1: <VGA-compatible display> at device 2.1 on pci0 pcib1: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 pcib1: secondary bus 2 pcib1: subordinate bus 2 pcib1: I/O decode 0x3000-0x3fff pcib1: memory decode 0xb4000000-0xb7ffffff pcib1: prefetched decode 0xd0000000-0xd3ffffff pci2: <ACPI PCI bus> on pcib1 pci2: physical bus=2 found-> vendor=0x11ab, dev=0x4351, revid=0x10 bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x4010, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 2 messages, 64 bit map[10]: type 1, range 64, base b4000000, size 14, enabled pcib1: (null) requested memory range 0xb4000000-0xb4003fff: good map[18]: type 4, range 32, base 00003000, size 8, enabled pcib1: (null) requested I/O range 0x3000-0x30ff: in range pcib1: matched entry for 2.0.INTA pcib1: slot 0 INTA hardwired to IRQ 16 pci2: <network, ethernet> at device 0.0 (no driver attached) uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0x1820-0x183f irq 19 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1820 ioapic0: routing intpin 19 (PCI IRQ 19) to vector 49 uhci0: [GIANT-LOCKED] usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0x1840-0x185f irq 23 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1840 ioapic0: routing intpin 23 (PCI IRQ 23) to vector 50 uhci1: [GIANT-LOCKED] usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0x1860-0x187f irq 22 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1860 ioapic0: routing intpin 22 (PCI IRQ 22) to vector 51 uhci2: [GIANT-LOCKED] usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 uhub2: 2 ports with 2 removable, self powered uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0x1880-0x189f irq 22 at device 29.3 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1880 uhci3: [GIANT-LOCKED] usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3 usb3: USB revision 1.0 uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 uhub3: 2 ports with 2 removable, self powered ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem 0xb0040000-0xb00403ff irq 19 at device 29.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xb0040000 ehci0: [GIANT-LOCKED] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 uhub4: 8 ports with 8 removable, self powered pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib2: secondary bus 6 pcib2: subordinate bus 7 pcib2: I/O decode 0xf000-0xfff pcib2: memory decode 0xb8000000-0xb80fffff pcib2: prefetched decode 0xfff00000-0xfffff pcib2: Subtractively decoded bridge. pci6: <ACPI PCI bus> on pcib2 pci6: physical bus=6 found-> vendor=0x14e4, dev=0x4318, revid=0x02 bus=6, slot=4, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 map[10]: type 1, range 32, base b8004000, size 13, enabled pcib2: (null) requested memory range 0xb8004000-0xb8005fff: good pcib2: matched entry for 6.4.INTA pcib2: slot 4 INTA hardwired to IRQ 17 found-> vendor=0x104c, dev=0x8031, revid=0x00 bus=6, slot=9, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x32 (1500 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base 00000000, size 12, enabled found-> vendor=0x104c, dev=0x8032, revid=0x00 bus=6, slot=9, func=2 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0016, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x04 (1000 ns) intpin=c, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base b8008000, size 11, enabled pcib2: (null) requested memory range 0xb8008000-0xb80087ff: good map[14]: type 1, range 32, base b8000000, size 14, enabled pcib2: (null) requested memory range 0xb8000000-0xb8003fff: good pcib2: matched entry for 6.9.INTC pcib2: slot 9 INTC hardwired to IRQ 18 found-> vendor=0x104c, dev=0x8033, revid=0x00 bus=6, slot=9, func=3 class=01-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x39 (1710 ns), mingnt=0x07 (1750 ns), maxlat=0x04 (1000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base b8006000, size 13, enabled pcib2: (null) requested memory range 0xb8006000-0xb8007fff: good pcib2: matched entry for 6.9.INTA pcib2: slot 9 INTA hardwired to IRQ 16 found-> vendor=0x104c, dev=0x8034, revid=0x00 bus=6, slot=9, func=4 class=08-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x39 (1710 ns), mingnt=0x07 (1750 ns), maxlat=0x04 (1000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base b8009000, size 8, enabled pcib2: (null) requested memory range 0xb8009000-0xb80090ff: good map[14]: type 1, range 32, base b8008c00, size 8, enabled pcib2: (null) requested memory range 0xb8008c00-0xb8008cff: good map[18]: type 1, range 32, base b8008800, size 8, enabled pcib2: (null) requested memory range 0xb8008800-0xb80088ff: good pcib2: matched entry for 6.9.INTA pcib2: slot 9 INTA hardwired to IRQ 16 ndis0: <Dell TrueMobile 1300 WLAN Mini-PCI Card> mem 0xb8004000-0xb8005fff irq 17 at device 4.0 on pci6 ndis0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0xb8004000 ioapic0: routing intpin 17 (PCI IRQ 17) to vector 52 ndis0: [MPSAFE] ndis0: NDIS API version: 5.1 ndis0: bpf attached ndis0: Ethernet address: 00:14:a5:80:f5:c9 ndis0: bpf attached cbb0: <TI6411 PCI-CardBus Bridge> at device 9.0 on pci6 pcib2: cbb0 requested memory range 0xb8000000-0xb80fffff: good cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xb800a000 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 pcib2: matched entry for 6.9.INTA pcib2: slot 9 INTA hardwired to IRQ 16 ioapic0: routing intpin 16 (PCI IRQ 16) to vector 53 cbb0: [MPSAFE] cbb0: PCI Configuration space: 0x00: 0x8031104c 0x02100007 0x06070000 0x00823200 0x10: 0xb800a000 0x020000a0 0x20030200 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x07400110 0x40: 0x0365107b 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x0844d061 0x00000000 0x000f0000 0x01ac1b22 0x90: 0x606482c0 0x00000000 0x00000000 0x00000000 0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000 0xb0: 0x08000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 fwohci0: vendor=104c, dev=8032 fwohci0: vendor=104c, dev=8032 fwohci0: <1394 Open Host Controller Interface> mem 0xb8008000-0xb80087ff,0xb8000000-0xb8003fff irq 18 at device 9.2 on pci6 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xb8008000 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 54 fwohci0: [MPSAFE] fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:e0:b8:03:65:02:20:31 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:e0:b8:02:20:31 fwe0: bpf attached fwe0: Ethernet address: 02:e0:b8:02:20:31 fwe0: if_start running deferred for Giant sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc000ffc0, gen=2, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) fwohci0: phy int pci6: <mass storage> at device 9.3 (no driver attached) pci6: <base peripheral> at device 9.4 (no driver attached) pcm0: <Intel ICH6 (82801FB)> port 0x1c00-0x1cff,0x18c0-0x18ff mem 0xb0040800-0xb00409ff,0xb0040400-0xb00404ff irq 21 at device 30.2 on pci0 pcm0: Reserved 0x200 bytes for rid 0x18 type 3 at 0xb0040800 pcm0: Reserved 0x100 bytes for rid 0x1c type 3 at 0xb0040400 ioapic0: routing intpin 21 (PCI IRQ 21) to vector 55 pcm0: [MPSAFE] pcm0: <Conexant CX20468-21 AC97 Codec (id = 0x43585430)> pcm0: Codec features reserved, headphone, 18 bit DAC, 18 bit ADC, 5 bit master volume, no 3D Stereo Enhancement pcm0: Primary codec extended features reserved 1, AMAP, reserved 5 pcm0: ac97 codec dac ready count: 0 pcm0: sndbuf_setmap efc6000, 4000; 0xcc2a0000 -> efc6000 pcm0: sndbuf_setmap efbc000, 4000; 0xcc2a4000 -> efbc000 pci0: <simple comms, generic modem> at device 30.3 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1810-0x181f at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1810 ata0: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=50 ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80 ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata0: stat1=0x50 err=0x01 lsb=0x14 msb=0xeb ata0: reset tp2 stat0=50 stat1=50 devices=0x9<ATAPI_SLAVE,ATA_MASTER> ioapic0: routing intpin 14 (ISA IRQ 14) to vector 56 ata0: [MPSAFE] ata1: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=00 ostat0=ff ostat1=ff ioapic0: routing intpin 15 (ISA IRQ 15) to vector 57 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_tz0: <Thermal Zone> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 58 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0047 psm0: <PS/2 Mouse> irq 12 on atkbdc0 ioapic0: routing intpin 12 (ISA IRQ 12) to vector 59 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete ex_isa_identify() unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ahc_isa_probe 1: ioport 0x1c00 alloc failed sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xcf800-0xd0fff,0xdc000-0xdffff,0xe0000-0xe07ff pnpid ORM0000 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x4e01 0x4e01 0x4e01 0x4e01 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x4e01 0x4e01 0x4e01 0x4e01 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding ioapic0: routing intpin 4 (ISA IRQ 4) to vector 60 sio0: [FAST] sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x4e01 0x4e01 0x4e01 0x4e01 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered lapic: Divisor 2, Frequency 50488942 hz Timecounter "TSC" frequency 1514668172 Hz quality 800 Timecounters tick every 1.000 msec lo0: bpf attached rr232x: no controller detected. acpi_acad0: acline initialization start battery0: battery initialization start ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire ad0: setting PIO4 on ICH6 chip ad0: setting UDMA100 on ICH6 chip ad0: 57231MB <HTS541060G9AT00 MB3VA60A> at ata0-master UDMA100 ad0: 117210240 sectors [116280C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad0 acpi_acad0: On Line acpi_acad0: acline initialization done, tried 1 times battery0: battery initialization done, tried 1 times ad0: Intel check1 failed ad0: Adaptec check1 failed ad0: LSI (v3) check1 failed ad0: LSI (v2) check1 failed ad0: FreeBSD check1 failed acd0: setting PIO4 on ICH6 chip acd0: setting UDMA33 on ICH6 chip acd0: <PHILIPS CD-RW/DVD-ROM SCB5265/TX09> CDRW drive at ata0 as slave acd0: read 689KB/s (4126KB/s) write 4126KB/s (4126KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc pcm0: measured ac97 link rate at 48012 Hz, will use 48000 Hz (probe0:sbp0:0:0:0): error 22 (probe0:sbp0:0:0:0): Unretryable Error (probe3:sbp0:0:3:0): error 22 (probe3:sbp0:0:3:0): Unretryable Error (probe4:sbp0:0:4:0): error 22 (probe4:sbp0:0:4:0): Unretryable Error (probe1:sbp0:0:1:0): error 22 (probe1:sbp0:0:1:0): Unretryable Error (probe2:sbp0:0:2:0): error 22 (probe2:sbp0:0:2:0): Unretryable Error (probe5:sbp0:0:5:0): error 22 (probe5:sbp0:0:5:0): Unretryable Error (probe6:sbp0:0:6:0): error 22 (probe6:sbp0:0:6:0): Unretryable Error ATA PseudoRAID loaded Trying to mount root from ufs:/dev/ad0s3a start_init: trying /sbin/init Linux ELF exec handler installed map[10]: type 1, range 64, base b4000000, size 14, enabled pcib2: (null) requested memory range 0xb4000000-0xb4003fff: good cbb alloc res fail map[18]: type 4, range 32, base 00003000, size 8, enabled cbb alloc res fail found-> vendor=0x11ab, dev=0x4351, revid=0x10 bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x4010, cachelnsz=8 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 2 messages, 64 bit cardbus0: <network, ethernet> at device 0.0 (no driver attached)Received on Sat Aug 05 2006 - 19:22:21 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:58 UTC