I've had similar issues with SCSI on the s2895, but with Adaptec PCI-X raid instead of the onboard LSI raid. If I put the card in the PCI-X 133Mhz slot, then it fails to see the OptionROM on boot, however if I put it in the second from last slot with an Audigy 2 in the last slot... it freezes in the exact point you describe. However if I put it in the third from last and the Audigy in the second from last then it runs like a charm! I think there are some serious issues with this mainboard in regard to these PCI-X slots. I've seen nothing but strangeness with them since I got this mainboard. On a related note, I have a GeForce 7900 and a Radeon X1800XT in my two PCIe slots. If the GeForce is in PCIe PCIe slot1 and the Radeon in PCIe slot2 while using the Adaptec SCSI, it hardlocks in the area you described. However once I swapped those two graphics cards it booted fine... maybe it's some kind of crazy resource mapping issue? Have you tried running the latest BIOS version on the board? I think it's up to 1.3l now, with tons of bug fixes. -- Regards, Chris Gilbert On Wednesday 23 August 2006 00:39, Michael Sinatra wrote: > Hi, > > In the past FreeBSD 6-CURRENT and RELENG_6 would (and still do) hang > when booting on a Tyan Thunder s2895 mobo with integrated LSI 1030 SCSI > controller, just after resetting the scsi bus and scanning for disks. > One workaround was to not use SCSI disks, and instead use SATA. Another > workaround was to go into the BIOS config and do the following: > > o disable Slave MAC (second nVidia ethernet) > o disable IEEE 1394 > o enable bus master on the SCSI controller > > In this configuration, RELENG_6/amd64 runs like a champ on this mobo. > > Unfortunately, my attempts to boot with 7-CURRENT, either the snapshot > 8/06 CD or a version build from source supped as of 8/15/06, have met > with complete failure. A complete dmesg is included below. > > The only way I can get 7-CURRENT to boot is by disabling the SCSI > controller. However, this box has a nice SCSI backplane and plenty of > SCSI disks, and no room for SATA. > > o The same configuration that works for RELENG_6 doesn't work for > CURRENT. I have gone even further and disabled just about everything > that the system needs to boot except for the SCSI controller and it > still hangs. > o The SCSI controller is running the latest BIOS and firmware. > o The problem occurs regardless of the version of BIOS that is on this > mobo (including beta versions)--I have tested several versions. > o I have tried both an amd64 kernel and an i386 kernel, both with the > same result. > o I built a custom, minimal kernel (using a non-mpt amd64 build > machine), that also failed on the s2895. > > Any ideas? It appears that the driver either isn't understanding this > card's handshake registers or it's not able to read the responses to > SCSI commands. > > Here's the dmesg. Let me know if there is other information that I can > provide. I'd like to test the nfe driver on the nVidia ethernet > interfaces on this box, but I can't boot it under these circumstances. > > michael > > Hit [Enter] to boot immediately, or any other key for command prompt. > Booting [/boot/kernel/kernel]... > GDB: no debug ports present > KDB: debugger backends: ddb > KDB: current backend: ddb > Copyright (c) 1992-2006 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 7.0-CURRENT #2: Fri Aug 18 23:19:57 PDT 2006 > michael_at_ncs-211.net.berkeley.edu:/usr/obj/usr/src/sys/GENERIC > WARNING: WITNESS option enabled, expect reduced performance. > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: AMD Opteron(tm) Processor 250 (2411.12-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10 > > Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA >,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD > Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow!+,3DNow!> > usable memory = 3208052736 (3059 MB) > avail memory = 3102224384 (2958 MB) > ACPI APIC Table: <PTLTD APIC > > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 1 > ioapic0 <Version 1.1> irqs 0-23 on motherboard > ioapic1 <Version 1.1> irqs 24-27 on motherboard > ioapic2 <Version 1.1> irqs 28-31 on motherboard > kbd0 at kbdmux0 > ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > acpi0: <PTLTD RSDT> on motherboard > acpi0: Power Button (fixed) > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: <memory> at device 0.0 (no driver attached) > isab0: <PCI-ISA bridge> at device 1.0 on pci0 > isa0: <ISA bus> on isab0 > pci0: <serial bus, SMBus> at device 1.1 (no driver attached) > ohci0: <OHCI (generic) USB controller> mem 0xc8000000-0xc8000fff irq 20 > at device 2.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 > uhub0: 10 ports with 10 removable, self powered > atapci0: <nVidia nForce CK804 UDMA133 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1400-0x140f at device 6.0 on pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > nve0: <NVIDIA nForce MCP8 Networking Adapter> port 0x1410-0x1417 mem > 0xc8001000-0xc8001fff irq 21 at device 10.0 on pci0 > nve0: Ethernet address 00:e0:81:54:a9:26 > miibus0: <MII bus> on nve0 > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > nve0: Ethernet address: 00:e0:81:54:a9:26 > pcib2: <ACPI PCI-PCI bridge> at device 14.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > vgapci0: <VGA-compatible display> port 0x2000-0x20ff mem > 0xd0000000-0xd7ffffff,0xc8200000-0xc820ffff irq 16 at device 0.0 on pci2 > vgapci1: <VGA-compatible display> mem 0xc8210000-0xc821ffff at device > 0.1 on pci2 > pcib3: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci8: <ACPI PCI bus> on pcib3 > pcib4: <ACPI PCI-PCI bridge> at device 10.0 on pci8 > pci9: <ACPI PCI bus> on pcib4 > em0: <Intel(R) PRO/1000 Network Connection Version - 6.1.4> port > 0x3000-0x303f mem 0xd8140000-0xd815ffff,0xd8100000-0xd813ffff irq 24 at > device 4.0 on pci9 > em0: Ethernet address: 00:04:23:b5:d8:7a > em0: [FAST] > em1: <Intel(R) PRO/1000 Network Connection Version - 6.1.4> port > 0x3040-0x307f mem 0xd8160000-0xd817ffff,0xd8180000-0xd81bffff irq 25 at > device 4.1 on pci9 > em1: Ethernet address: 00:04:23:b5:d8:7b > em1: [FAST] > pci8: <base peripheral, interrupt controller> at device 10.1 (no driver > attached) > pcib5: <ACPI PCI-PCI bridge> at device 11.0 on pci8 > pci10: <ACPI PCI bus> on pcib5 > em2: <Intel(R) PRO/1000 Network Connection Version - 6.1.4> port > 0x4800-0x483f mem 0xd8240000-0xd825ffff,0xd8200000-0xd823ffff irq 28 at > device 4.0 on pci10 > em2: Ethernet address: 00:04:23:b6:2c:c4 > em2: [FAST] > em3: <Intel(R) PRO/1000 Network Connection Version - 6.1.4> port > 0x4840-0x487f mem 0xd8260000-0xd827ffff,0xd8280000-0xd82bffff irq 29 at > device 4.1 on pci10 > em3: Ethernet address: 00:04:23:b6:2c:c5 > em3: [FAST] > mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x4000-0x40ff mem > 0xd8400000-0xd84fffff,0xd8300000-0xd83fffff irq 30 at device 6.0 on pci10 > mpt0: [GIANT-LOCKED] > mpt0: MPI Version=1.2.14.0 > mpt1: <LSILogic 1030 Ultra4 Adapter> port 0x4400-0x44ff mem > 0xd8600000-0xd86fffff,0xd8500000-0xd85fffff irq 31 at device 6.1 on pci10 > mpt1: [GIANT-LOCKED] > mpt1: MPI Version=1.2.14.0 > mpt1: mpt_wait_req(4) timed out > mpt1: read_cfg_header timed out > mpt1: mpt_wait_req(6) timed out > mpt1: port 0 enable timed out > mpt1: failed to enable port 0 > mpt1: personality mpt_core attached but would not enable (6) > pci8: <base peripheral, interrupt controller> at device 11.1 (no driver > attached) > pcib6: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci128: <ACPI PCI bus> on pcib6 > pci128: <memory> at device 0.0 (no driver attached) > pci128: <memory> at device 1.0 (no driver attached) > pcib7: <ACPI PCI-PCI bridge> at device 14.0 on pci128 > pci129: <ACPI PCI bus> on pcib7 > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on > acpi0 > sio0: type 16550A, console > sio0: [FAST] > fdc0: <floppy drive controller> port 0-0x5,0 on acpi0 > fdc0: cannot reserve interrupt line > device_attach: fdc0 attach returned 6 > fdc0: <floppy drive controller> port 0-0x5,0 on acpi0 > fdc0: cannot reserve interrupt line > device_attach: fdc0 attach returned 6 > ppc0: <Parallel port> port 0-0x7 on acpi0 > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > ppbus0: <Parallel port bus> on ppc0 > plip0: cannot reserve interrupt, failed. > lpt0: <Printer> on ppbus0 > lpt0: Polled port > ppi0: <Parallel I/O> on ppbus0 > orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xd0fff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounters tick every 1.000 msec > mpt0: Default Handler Called: req=0xffffffff80e48ff8:94 > reply_descriptor=dc913900 frame=0xffffffffacc7a200 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a200 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003005d > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49050:95 > reply_descriptor=dc913980 frame=0xffffffffacc7a300 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a300 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003005e > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e490a8:96 > reply_descriptor=dc913a00 frame=0xffffffffacc7a400 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a400 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003005f > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49100:97 > reply_descriptor=dc913a80 frame=0xffffffffacc7a500 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a500 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030060 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49158:98 > reply_descriptor=dc913b00 frame=0xffffffffacc7a600 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a600 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030061 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e491b0:99 > reply_descriptor=dc913b80 frame=0xffffffffacc7a700 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a700 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030062 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49208:100 > reply_descriptor=dc913c00 frame=0xffffffffacc7a800 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a800 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030063 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49260:101 > reply_descriptor=dc913c80 frame=0xffffffffacc7a900 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a900 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030064 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e492b8:102 > reply_descriptor=dc913d00 frame=0xffffffffacc7aa00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7aa00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030065 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49310:103 > reply_descriptor=dc913d80 frame=0xffffffffacc7ab00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ab00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030066 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49368:104 > reply_descriptor=dc913e00 frame=0xffffffffacc7ac00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ac00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030067 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e493c0:105 > reply_descriptor=dc913e80 frame=0xffffffffacc7ad00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ad00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030068 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49418:106 > reply_descriptor=dc913f00 frame=0xffffffffacc7ae00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ae00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030069 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49470:107 > reply_descriptor=dc913800 frame=0xffffffffacc7a000 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a000 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003006a > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e494c8:108 > reply_descriptor=dc913880 frame=0xffffffffacc7a100 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a100 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003006b > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49520:109 > reply_descriptor=dc913900 frame=0xffffffffacc7a200 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a200 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003006c > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49578:110 > reply_descriptor=dc913980 frame=0xffffffffacc7a300 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a300 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003006d > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e495d0:111 > reply_descriptor=dc913a00 frame=0xffffffffacc7a400 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a400 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003006e > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49628:112 > reply_descriptor=dc913a80 frame=0xffffffffacc7a500 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a500 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003006f > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49680:113 > reply_descriptor=dc913b00 frame=0xffffffffacc7a600 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a600 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030070 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e496d8:114 > reply_descriptor=dc913b80 frame=0xffffffffacc7a700 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a700 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030071 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49730:115 > reply_descriptor=dc913c00 frame=0xffffffffacc7a800 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a800 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030072 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49788:116 > reply_descriptor=dc913c80 frame=0xffffffffacc7a900 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a900 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030073 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e497e0:117 > reply_descriptor=dc913d00 frame=0xffffffffacc7aa00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7aa00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030074 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49838:118 > reply_descriptor=dc913d80 frame=0xffffffffacc7ab00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ab00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030075 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49890:119 > reply_descriptor=dc913e00 frame=0xffffffffacc7ac00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ac00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030076 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e498e8:120 > reply_descriptor=dc913e80 frame=0xffffffffacc7ad00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ad00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030077 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49940:121 > reply_descriptor=dc913f00 frame=0xffffffffacc7ae00 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7ae00 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030078 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49998:122 > reply_descriptor=dc913800 frame=0xffffffffacc7a000 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a000 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x00030079 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e499f0:123 > reply_descriptor=dc913880 frame=0xffffffffacc7a100 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a100 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003007a > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49a48:124 > reply_descriptor=dc913900 frame=0xffffffffacc7a200 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a200 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003007b > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49aa0:125 > reply_descriptor=dc913980 frame=0xffffffffacc7a300 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffffacc7a300 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x05 > MsgFlags 0x00 > MsgContext 0x0003007c > mpt0: Reply Frame Ignored > em1: link state changed to UP > em2: link state changed to UP > em3: link state changed to UP > acd0: CDROM <SR244W/T01A> at ata0-master UDMA33 > Waiting 5 seconds for SCSI devices to settle > mpt0: Default Handler Called: req=0xffffffff80e47160:126 > reply_descriptor=dc913a00 frame=0xffffffffacc7a400 > mpt0: Address Reply: > SCSI Task Management Reply _at_ 0xffffffffacc7a400 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x06 > MsgFlags 0x00 > MsgContext 0x00020004 > mpt0: Reply Frame Ignored > mpt0: mpt_wait_req(1) timed out > mpt0: mpt_bus_reset: Reset timed-out. Resetting controller. > mpt0: Default Handler Called: req=0xffffffff80e47160:126 > reply_descriptor=20004 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Task Management Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00020004 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49aa0:125 > reply_descriptor=3007c frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003007c > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49a48:124 > reply_descriptor=3007b frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003007b > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e499f0:123 > reply_descriptor=3007a frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003007a > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49998:122 > reply_descriptor=30079 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030079 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49940:121 > reply_descriptor=30078 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030078 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e498e8:120 > reply_descriptor=30077 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030077 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49890:119 > reply_descriptor=30076 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030076 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49838:118 > reply_descriptor=30075 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030075 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e497e0:117 > reply_descriptor=30074 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030074 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49788:116 > reply_descriptor=30073 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030073 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49730:115 > reply_descriptor=30072 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030072 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e496d8:114 > reply_descriptor=30071 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030071 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49680:113 > reply_descriptor=30070 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030070 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49628:112 > reply_descriptor=3006f frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003006f > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e495d0:111 > reply_descriptor=3006e frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003006e > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49578:110 > reply_descriptor=3006d frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003006d > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49520:109 > reply_descriptor=3006c frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003006c > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e494c8:108 > reply_descriptor=3006b frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003006b > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49470:107 > reply_descriptor=3006a frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003006a > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49418:106 > reply_descriptor=30069 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030069 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e493c0:105 > reply_descriptor=30068 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030068 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49368:104 > reply_descriptor=30067 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030067 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49310:103 > reply_descriptor=30066 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030066 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e492b8:102 > reply_descriptor=30065 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030065 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49260:101 > reply_descriptor=30064 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030064 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49208:100 > reply_descriptor=30063 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030063 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e491b0:99 > reply_descriptor=30062 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030062 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49158:98 > reply_descriptor=30061 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030061 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49100:97 > reply_descriptor=30060 frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00030060 > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e490a8:96 > reply_descriptor=3005f frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003005f > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e49050:95 > reply_descriptor=3005e frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003005e > mpt0: Reply Frame Ignored > mpt0: Default Handler Called: req=0xffffffff80e48ff8:94 > reply_descriptor=3005d frame=0xffffffff80b49b10 > mpt0: Address Reply: > SCSI Target Command Buffer Reply _at_ 0xffffffff80b49b10 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0003005d > mpt0: Reply Frame Ignored > mpt0: mpt_cam_event: 0x0 > mpt0: Default Handler Called: req=0xffffffff80e49ba8:129 > reply_descriptor=1007f frame=0 > mpt0: Reply Frame Ignored > mpt0: request 0xffffffff80e49ba8:129 timed out for ccb > 0xffffff00b7d81800 (req->ccb 0xffffff00b7d81800) > mpt0: attempting to abort req 0xffffffff80e49ba8:129 function 0 > mpt0: Default Handler Called: req=0xffffffff80e47160:130 > reply_descriptor=dc913900 frame=0xffffffffacc7a200 > mpt0: Address Reply: > SCSI Task Management Reply _at_ 0xffffffffacc7a200 > IOC Status Success > IOCLogInfo 0x00000000 > MsgLength 0x06 > MsgFlags 0x00 > MsgContext 0x00020004 > mpt0: Reply Frame Ignored > mpt0: mpt_wait_req(1) timed out > mpt0: mpt_recover_commands: abort timed-out. Resetting controller > mpt0: Default Handler Called: req=0xffffffff80e47160:130 > reply_descriptor=20004 frame=0xffffffffac25db90 > mpt0: Address Reply: > SCSI Task Management Reply _at_ 0xffffffffac25db90 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x00020004 > mpt0: Reply Frame Ignored > mpt0: mpt_cam_event: 0x0 > mpt0: Default Handler Called: req=0xffffffff80e49ba8:129 > reply_descriptor=1007f frame=0xffffffffac25db70 > mpt0: Address Reply: > SCSI IO Request Reply _at_ 0xffffffffac25db70 > IOC Status IOC: Invalid State > IOCLogInfo 0x00000000 > MsgLength 0x14 > MsgFlags 0x00 > MsgContext 0x0001007f > Bus: 0 > TargetID 0 > CDBLength 0 > SCSI Status: OK > SCSI State: (0x00000000) > TransferCnt 0xffffffff > SenseCnt 0x803104e7 > ResponseInfo 0xffffffff > mpt0: Reply Frame Ignored > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"Received on Tue Aug 22 2006 - 21:04:53 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:59 UTC