We've been trying to get FreeBSD (-CURRENT and -STABLE) booted on these new Dells (as others have too it seems). We have both a Precision 390 and an OptiPlex 745 system. Both boot, but neither one has a supported NIC - maybe just PCI ID's? The OptiPlex 745 system has this broadcom chip (from the physical markings on the chip): BCM5754KMLG UA0620 P12 782801 2 pciconf -lv says: bge0_at_pci3:0:0: class=0x020000 card=0x01da1028 chip=0x167a14e4 rev=0x02 hdr=0x00 vendor = 'Broadcom Corporation' class = network subclass = ethernet Snippet from dmesg shows: pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xf000-0xfff pcib3: memory decode 0xdfa00000-0xdfafffff pcib3: prefetched decode 0xfff00000-0xfffff pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 found-> vendor=0x14e4, dev=0x167a, revid=0x02 bus=3, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 3 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base dfaf0000, size 16, enabled pcib3: (null) requested memory range 0xdfaf0000-0xdfafffff: good pcib3: matched entry for 3.0.INTA pcib3: slot 0 INTA hardwired to IRQ 16 bge0: <Broadcom unknown BCM5787, ASIC rev. 0xb002> mem 0xdfaf0000-0xdfafffff irq 16 at device 0.0 on pci3 bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xdfaf0000 bge0: firmware handshake timed out bge0: RX CPU self-diagnostics failed! bge0: chip initialization failed device_attach: bge0 attach returned 6 I've attached the full dmesg output for this system. What are the next steps in figuring out support for this chip? Now, on the Precision 390, the kernel panics when detecting the NIC - NMI memory issue, but I can't recall the error. The physical chip in this system looks like: BCM5754KMLG UA0617 P12 780856 2 I can provide any additional information needed if someone would like to look into it. Eric -- ------------------------------------------------------------------------ Eric Anderson Sr. Systems Administrator Centaur Technology Anything that works is better than anything that doesn't. ------------------------------------------------------------------------ Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.2-BETA3 #0: Mon Oct 30 22:03:42 UTC 2006 root_at_meyers.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80a67000. INTR: Adding local APIC 0 as a target ACPI APIC Table: <DELL B8K > Calibrating clock(s) ... i8254 clock: 1193189 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2660011320 Hz CPU: Intel(R) Core(TM)2 CPU 6700 _at_ 2.66GHz (2660.01-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>> AMD Features=0x20000800<SYSCALL,LM> AMD Features2=0x1<LAHF> Cores per package: 2 real memory = 2137190400 (2038 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages) 0x0000000000b64000 - 0x000000007ba28fff, 2062307328 bytes (503493 pages) avail memory = 2052075520 (1957 MB) INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000 ioapic0: Changing APIC ID to 8 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: high lapic: Routing NMI -> LINT1 lapic: LINT1 trigger: level lapic: LINT1 polarity: high ioapic0 <Version 2.0> irqs 0-23 on motherboard lapic0: Forcing LINT1 to edge trigger cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 wlan: <802.11 Link Layer> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> null: <null device, zero device> random: <entropy source, Software, Yarrow> nfslock: pseudo-device kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> io: <I/O> ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Oct 30 2006 22:03:31) acpi0: <DELL B8K > on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80001020 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=29908086) acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 9 10 11 12 15 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 9 10 11 12 15 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 9 10 11 12 15 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 9 10 11 12 15 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 3 N 0 3 4 5 6 7 9 10 11 12 15 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 3 N 0 3 4 5 6 7 9 10 11 12 15 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link4: Links after initial probe: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 9 10 11 12 15 pci_link4: Links after initial validation: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 9 10 11 12 15 pci_link4: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link5: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link5: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link5: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link6: Links after initial probe: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 9 10 11 12 15 pci_link6: Links after initial validation: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 9 10 11 12 15 pci_link6: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 pci_link7: Links after initial probe: Index IRQ Rtd Ref IRQs 0 5 N 0 3 4 5 6 7 9 10 11 12 15 pci_link7: Links after initial validation: Index IRQ Rtd Ref IRQs 0 5 N 0 3 4 5 6 7 9 10 11 12 15 pci_link7: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 15 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x2990, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2991, revid=0x02 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 pcib0: matched entry for 0.1.INTA pcib0: slot 1 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x2992, revid=0x02 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0003, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message map[10]: type 1, range 32, base dfe00000, size 20, enabled map[18]: type 3, range 64, base c0000000, size 28, enabled map[20]: type 4, range 32, base 0000ecb8, size 3, enabled pcib0: matched entry for 0.2.INTA pcib0: slot 2 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x2993, revid=0x02 bus=0, slot=2, func=1 class=03-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base dff00000, size 20, enabled found-> vendor=0x8086, dev=0x2834, revid=0x02 bus=0, slot=26, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[20]: type 4, range 32, base 0000ff20, size 5, enabled pcib0: matched entry for 0.26.INTA pcib0: slot 26 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x2835, revid=0x02 bus=0, slot=26, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 map[20]: type 4, range 32, base 0000ff00, size 5, enabled pcib0: matched entry for 0.26.INTB pcib0: slot 26 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x283a, revid=0x02 bus=0, slot=26, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=9 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base dfdfbc00, size 10, enabled pcib0: matched entry for 0.26.INTC pcib0: slot 26 INTC hardwired to IRQ 22 found-> vendor=0x8086, dev=0x284b, revid=0x02 bus=0, slot=27, func=0 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base dfdfc000, size 14, enabled pcib0: matched entry for 0.27.INTA pcib0: slot 27 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x283f, revid=0x02 bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 pcib0: matched entry for 0.28.INTA pcib0: slot 28 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x2847, revid=0x02 bus=0, slot=28, func=4 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 pcib0: matched entry for 0.28.INTA pcib0: slot 28 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x2830, revid=0x02 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 map[20]: type 4, range 32, base 0000ff80, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 23 found-> vendor=0x8086, dev=0x2831, revid=0x02 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 map[20]: type 4, range 32, base 0000ff60, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x2832, revid=0x02 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=3 map[20]: type 4, range 32, base 0000ff40, size 5, enabled pcib0: matched entry for 0.29.INTC pcib0: slot 29 INTC hardwired to IRQ 18 found-> vendor=0x8086, dev=0x2836, revid=0x02 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base ff980800, size 10, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 23 found-> vendor=0x8086, dev=0x244e, revid=0xf2 bus=0, slot=30, func=0 class=06-04-01, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2810, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2820, revid=0x02 bus=0, slot=31, func=2 class=01-01-8f, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=9 powerspec 3 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000fe00, size 3, enabled map[14]: type 4, range 32, base 0000fe10, size 2, enabled map[18]: type 4, range 32, base 0000fe20, size 3, enabled map[1c]: type 4, range 32, base 0000fe30, size 2, enabled map[20]: type 4, range 32, base 0000fec0, size 4, enabled map[24]: type 4, range 32, base 0000ecc0, size 4, enabled pcib0: matched entry for 0.31.INTC pcib0: slot 31 INTC hardwired to IRQ 20 found-> vendor=0x8086, dev=0x283e, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0103, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=9 map[10]: type 1, range 32, base dfdfbb00, size 8, enabled map[20]: type 4, range 32, base 0000ece0, size 5, enabled pcib0: matched entry for 0.31.INTC pcib0: slot 31 INTC hardwired to IRQ 20 found-> vendor=0x8086, dev=0x2825, revid=0x02 bus=0, slot=31, func=5 class=01-01-85, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=9 powerspec 3 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000fe40, size 3, enabled map[14]: type 4, range 32, base 0000fe50, size 2, enabled map[18]: type 4, range 32, base 0000fe60, size 3, enabled map[1c]: type 4, range 32, base 0000fe70, size 2, enabled map[20]: type 4, range 32, base 0000fed0, size 4, enabled map[24]: type 4, range 32, base 0000ecd0, size 4, enabled pcib0: matched entry for 0.31.INTC pcib0: slot 31 INTC hardwired to IRQ 20 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xdfc00000-0xdfcfffff pcib1: prefetched decode 0xfff00000-0xfffff pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 pci0: <display, VGA> at device 2.0 (no driver attached) pci0: <display> at device 2.1 (no driver attached) uhci0: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 16 at device 26.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff20 ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49 uhci0: [GIANT-LOCKED] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xff00-0xff1f irq 17 at device 26.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff00 ioapic0: routing intpin 17 (PCI IRQ 17) to vector 50 uhci1: [GIANT-LOCKED] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdfdfbc00-0xdfdfbfff irq 22 at device 26.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdfdfbc00 ioapic0: routing intpin 22 (PCI IRQ 22) to vector 51 ehci0: [GIANT-LOCKED] usb2: waiting for BIOS to give up control usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <EHCI (generic) USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 4 ports with 4 removable, self powered pci0: <multimedia> at device 27.0 (no driver attached) pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xf000-0xfff pcib2: memory decode 0xdfb00000-0xdfbfffff pcib2: prefetched decode 0xfff00000-0xfffff pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xf000-0xfff pcib3: memory decode 0xdfa00000-0xdfafffff pcib3: prefetched decode 0xfff00000-0xfffff pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 found-> vendor=0x14e4, dev=0x167a, revid=0x02 bus=3, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 3 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base dfaf0000, size 16, enabled pcib3: (null) requested memory range 0xdfaf0000-0xdfafffff: good pcib3: matched entry for 3.0.INTA pcib3: slot 0 INTA hardwired to IRQ 16 bge0: <Broadcom unknown BCM5787, ASIC rev. 0xb002> mem 0xdfaf0000-0xdfafffff irq 16 at device 0.0 on pci3 bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xdfaf0000 bge0: firmware handshake timed out bge0: RX CPU self-diagnostics failed! bge0: chip initialization failed device_attach: bge0 attach returned 6 uhci2: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 23 at device 29.0 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff80 ioapic0: routing intpin 23 (PCI IRQ 23) to vector 52 uhci2: [GIANT-LOCKED] usb3: <UHCI (generic) USB controller> on uhci2 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered uhci3: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 17 at device 29.1 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff60 uhci3: [GIANT-LOCKED] usb4: <UHCI (generic) USB controller> on uhci3 usb4: USB revision 1.0 uhub4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub4: 2 ports with 2 removable, self powered uhci4: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0 uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff40 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 53 uhci4: [GIANT-LOCKED] usb5: <UHCI (generic) USB controller> on uhci4 usb5: USB revision 1.0 uhub5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub5: 2 ports with 2 removable, self powered ehci1: <EHCI (generic) USB 2.0 controller> mem 0xff980800-0xff980bff irq 23 at device 29.7 on pci0 ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0xff980800 ehci1: [GIANT-LOCKED] usb6: EHCI version 1.0 usb6: companion controllers, 2 ports each: usb3 usb4 usb5 usb6: <EHCI (generic) USB 2.0 controller> on ehci1 usb6: USB revision 2.0 uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub6: 6 ports with 6 removable, self powered pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib4: secondary bus 4 pcib4: subordinate bus 4 pcib4: I/O decode 0xf000-0xfff pcib4: memory decode 0xfff00000-0xfffff pcib4: prefetched decode 0xfff00000-0xfffff pcib4: Subtractively decoded bridge. pci4: <ACPI PCI bus> on pcib4 pci4: physical bus=4 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH8 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf,0xecc0-0xeccf irq 20 at device 31.2 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfec0 ioapic0: routing intpin 20 (PCI IRQ 20) to vector 54 atapci0: [MPSAFE] ata2: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe00 atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe10 ata2: reset tp1 mask=03 ostat0=50 ostat1=00 ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata3: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe20 atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe30 ata3: reset tp1 mask=03 ostat0=00 ostat1=00 ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> ata3: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) atapci1: <Intel ICH8 SATA300 controller> port 0xfe40-0xfe47,0xfe50-0xfe53,0xfe60-0xfe67,0xfe70-0xfe73,0xfed0-0xfedf,0xecd0-0xecdf irq 20 at device 31.5 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfed0 atapci1: [MPSAFE] ata4: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe40 atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe50 ata4: reset tp1 mask=00 ostat0=ff ostat1=ff ata4: [MPSAFE] ata5: <ATA channel 1> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe60 atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe70 ata5: reset tp1 mask=00 ostat0=ff ostat1=ff ata5: [MPSAFE] ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ioapic0: routing intpin 7 (ISA IRQ 7) to vector 55 sio0: irq maps: 0xca9 0xcb9 0xca9 0xca9 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56 ahc_isa_probe 0: ioport 0xc00 alloc failed ahc_isa_probe 2: ioport 0x2c00 alloc failed ahc_isa_probe 5: ioport 0x5c00 alloc failed ahc_isa_probe 6: ioport 0x6c00 alloc failed ahc_isa_probe 10: ioport 0xac00 alloc failed ahc_isa_probe 14: ioport 0xec00 alloc failed ex_isa_identify() ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xccfff,0xcd000-0xcefff,0xcf000-0xcffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0045 atkbd: keyboard ID 0xffffffff (1) atkbd: failed to reset the keyboard. kbd0 at atkbd0 kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 57 atkbd0: [GIANT-LOCKED] psm0: current command byte:0045 psm0: failed to reset the aux device. fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0xca9 0xca9 0xca9 0xca9 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 isa_probe_children: probing PnP devices ukbd0: DELL DELL USB Keyboard, rev 1.10/1.05, addr 2, iclass 3/1 kbd2 at ukbd0 kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000 Device configuration finished. Reducing kern.maxvnodes 132076 -> 100000 linprocfs registered procfs registered lapic: Divisor 2, Frequency 133000364 hz Timecounter "TSC" frequency 2660011320 Hz quality -100 Timecounters tick every 1.000 msec Linux ELF exec handler installed lo0: bpf attached rr232x: no controller detected. usb1: host controller halted ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad4: 76293MB <WDC WD800JD-75MSA3 10.01E04> at ata2-master SATA150 ad4: 156250000 sectors [155009C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 ad4: Intel check1 failed ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed ata3: reiniting channel .. ata3: reset tp1 mask=03 ostat0=00 ostat1=00 ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> ata3: reinit done .. ata3: reiniting channel .. ata3: reset tp1 mask=03 ostat0=00 ostat1=00 ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> ata3: reinit done .. ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire acd0: <TSSTcorpCD-ROM TS-L162C/DE00> CDROM drive at ata3 as master acd0: read 4134KB/s (4134KB/s), 96KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc ATA PseudoRAID loaded lapic1: Forcing LINT1 to edge trigger SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 INTR: Assigning IRQ 1 to local APIC 0 ioapic0: Assigning ISA IRQ 1 to local APIC 0 INTR: Assigning IRQ 4 to local APIC 1 ioapic0: Assigning ISA IRQ 4 to local APIC 1 INTR: Assigning IRQ 7 to local APIC 0 ioapic0: Assigning ISA IRQ 7 to local APIC 0 INTR: Assigning IRQ 9 to local APIC 1 ioapic0: Assigning ISA IRQ 9 to local APIC 1 INTR: Assigning IRQ 16 to local APIC 0 ioapic0: Assigning PCI IRQ 16 to local APIC 0 INTR: Assigning IRQ 17 to local APIC 1 ioapic0: Assigning PCI IRQ 17 to local APIC 1 INTR: Assigning IRQ 18 to local APIC 0 ioapic0: Assigning PCI IRQ 18 to local APIC 0 INTR: Assigning IRQ 20 to local APIC 1 ioapic0: Assigning PCI IRQ 20 to local APIC 1 INTR: Assigning IRQ 22 to local APIC 0 ioapic0: Assigning PCI IRQ 22 to local APIC 0 INTR: Assigning IRQ 23 to local APIC 1 ioapic0: Assigning PCI IRQ 23 to local APIC 1 Trying to mount root from ufs:/dev/ad4s1a start_init: trying /sbin/init umass0: Seagate USB Mass Storage, rev 2.00/0.01, addr 2 umass0: Get Max Lun not supported (STALLED) umass0:0:0:-1: Attached to scbus0 pass0 at umass-sim0 bus 0 target 0 lun 0 pass0: <ST940811 4A \\0000\\0000> Fixed Direct Access SCSI-0 device pass0: 40.000MB/s transfers GEOM: new disk da0 da0 at umass-sim0 bus 0 target 0 lun 0 da0: <ST940811 4A \\0000\\0000> Fixed Direct Access SCSI-0 device da0: 40.000MB/s transfers da0: 38154MB (78140160 512 byte sectors: 255H 63S/T 4864C)Received on Wed Nov 08 2006 - 15:18:44 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:02 UTC