here is a screen shot of the crash on the Precision 390. http://users.centtech.com/~kramer/broadcom/bge_prec390.jpg ------------------------------ Kevin Kramer Sr. Systems Administrator 512.418.5725 Centaur Technology, Inc. www.centtech.com Eric Anderson wrote the following on 11/08/06 10:17: > We've been trying to get FreeBSD (-CURRENT and -STABLE) booted on > these new Dells (as others have too it seems). We have both a > Precision 390 and an OptiPlex 745 system. Both boot, but neither one > has a supported NIC - maybe just PCI ID's? > > The OptiPlex 745 system has this broadcom chip (from the physical > markings on the chip): > BCM5754KMLG > UA0620 P12 > 782801 2 > > pciconf -lv says: > bge0_at_pci3:0:0: class=0x020000 card=0x01da1028 chip=0x167a14e4 > rev=0x02 hdr=0x00 > vendor = 'Broadcom Corporation' > class = network > subclass = ethernet > > Snippet from dmesg shows: > pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0 > pcib3: secondary bus 3 > pcib3: subordinate bus 3 > pcib3: I/O decode 0xf000-0xfff > pcib3: memory decode 0xdfa00000-0xdfafffff > pcib3: prefetched decode 0xfff00000-0xfffff > pci3: <ACPI PCI bus> on pcib3 > pci3: physical bus=3 > found-> vendor=0x14e4, dev=0x167a, revid=0x02 > bus=3, slot=0, func=0 > class=02-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > powerspec 3 supports D0 D3 current D0 > MSI supports 1 message, 64 bit > map[10]: type 1, range 64, base dfaf0000, size 16, enabled > pcib3: (null) requested memory range 0xdfaf0000-0xdfafffff: good > pcib3: matched entry for 3.0.INTA > pcib3: slot 0 INTA hardwired to IRQ 16 > bge0: <Broadcom unknown BCM5787, ASIC rev. 0xb002> mem > 0xdfaf0000-0xdfafffff irq 16 at device 0.0 on pci3 > bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xdfaf0000 > bge0: firmware handshake timed out > bge0: RX CPU self-diagnostics failed! > bge0: chip initialization failed > device_attach: bge0 attach returned 6 > > I've attached the full dmesg output for this system. > > What are the next steps in figuring out support for this chip? > > > Now, on the Precision 390, the kernel panics when detecting the NIC - > NMI memory issue, but I can't recall the error. The physical chip in > this system looks like: > > BCM5754KMLG > UA0617 P12 > 780856 2 > > I can provide any additional information needed if someone would like > to look into it. > > > Eric > > > > > ------------------------------------------------------------------------ > > Copyright (c) 1992-2006 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 6.2-BETA3 #0: Mon Oct 30 22:03:42 UTC 2006 > root_at_meyers.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP > Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80a67000. > INTR: Adding local APIC 0 as a target > ACPI APIC Table: <DELL B8K > > Calibrating clock(s) ... i8254 clock: 1193189 Hz > CLK_USE_I8254_CALIBRATION not specified - using default frequency > Timecounter "i8254" frequency 1193182 Hz quality 0 > Calibrating TSC clock ... TSC clock: 2660011320 Hz > CPU: Intel(R) Core(TM)2 CPU 6700 _at_ 2.66GHz (2660.01-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6 > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>> > AMD Features=0x20000800<SYSCALL,LM> > AMD Features2=0x1<LAHF> > Cores per package: 2 > real memory = 2137190400 (2038 MB) > Physical memory chunk(s): > 0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages) > 0x0000000000b64000 - 0x000000007ba28fff, 2062307328 bytes (503493 pages) > avail memory = 2052075520 (1957 MB) > INTR: Adding local APIC 1 as a target > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 1 > APIC: CPU 0 has ACPI ID 1 > APIC: CPU 1 has ACPI ID 2 > MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000 > ioapic0: Changing APIC ID to 8 > ioapic0: Routing external 8259A's -> intpin 0 > ioapic0: intpin 0 -> ExtINT (edge, high) > ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) > ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) > ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) > ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) > ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) > ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) > ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) > ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) > ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) > ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) > ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) > ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) > ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) > ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) > ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) > ioapic0: intpin 16 -> PCI IRQ 16 (level, low) > ioapic0: intpin 17 -> PCI IRQ 17 (level, low) > ioapic0: intpin 18 -> PCI IRQ 18 (level, low) > ioapic0: intpin 19 -> PCI IRQ 19 (level, low) > ioapic0: intpin 20 -> PCI IRQ 20 (level, low) > ioapic0: intpin 21 -> PCI IRQ 21 (level, low) > ioapic0: intpin 22 -> PCI IRQ 22 (level, low) > ioapic0: intpin 23 -> PCI IRQ 23 (level, low) > MADT: Interrupt override: source 0, irq 2 > ioapic0: Routing IRQ 0 -> intpin 2 > ioapic0: intpin 2 trigger: edge > ioapic0: intpin 2 polarity: high > MADT: Interrupt override: source 9, irq 9 > ioapic0: intpin 9 trigger: level > ioapic0: intpin 9 polarity: high > lapic: Routing NMI -> LINT1 > lapic: LINT1 trigger: level > lapic: LINT1 polarity: high > ioapic0 <Version 2.0> irqs 0-23 on motherboard > lapic0: Forcing LINT1 to edge trigger > cpu0 BSP: > ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff > lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff > timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 > wlan: <802.11 Link Layer> > ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> > null: <null device, zero device> > random: <entropy source, Software, Yarrow> > nfslock: pseudo-device > kbd: new array size 4 > kbd1 at kbdmux0 > mem: <memory> > io: <I/O> > ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > rr232x: RocketRAID 232x controller driver v1.02 (Oct 30 2006 22:03:31) > acpi0: <DELL B8K > on motherboard > ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 > acpi0: [MPSAFE] > pci_open(1): mode 1 addr port (0x0cf8) is 0x80001020 > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=29908086) > acpi_bus_number: root bus has no _BBN, assuming 0 > AcpiOsDerivePciId: bus 0 dev 31 func 0 > acpi_bus_number: root bus has no _BBN, assuming 0 > AcpiOsDerivePciId: bus 0 dev 31 func 0 > acpi0: Power Button (fixed) > ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > pci_link0: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 11 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link0: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 11 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link0: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link1: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 10 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link1: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 10 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link1: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link2: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 3 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link2: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 3 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link2: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link3: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link3: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link3: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link4: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 9 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link4: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 9 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link4: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link5: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link5: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link5: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link6: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 9 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link6: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 9 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link6: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link7: Links after initial probe: > Index IRQ Rtd Ref IRQs > 0 5 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link7: Links after initial validation: > Index IRQ Rtd Ref IRQs > 0 5 N 0 3 4 5 6 7 9 10 11 12 15 > pci_link7: Links after disable: > Index IRQ Rtd Ref IRQs > 0 255 N 0 3 4 5 6 7 9 10 11 12 15 > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: physical bus=0 > found-> vendor=0x8086, dev=0x2990, revid=0x02 > bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x8086, dev=0x2991, revid=0x02 > bus=0, slot=1, func=0 > class=06-04-00, hdrtype=0x01, mfdev=0 > cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) > lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > pcib0: matched entry for 0.1.INTA > pcib0: slot 1 INTA hardwired to IRQ 16 > found-> vendor=0x8086, dev=0x2992, revid=0x02 > bus=0, slot=2, func=0 > class=03-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0003, statreg=0x0090, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > powerspec 2 supports D0 D3 current D0 > MSI supports 1 message > map[10]: type 1, range 32, base dfe00000, size 20, enabled > map[18]: type 3, range 64, base c0000000, size 28, enabled > map[20]: type 4, range 32, base 0000ecb8, size 3, enabled > pcib0: matched entry for 0.2.INTA > pcib0: slot 2 INTA hardwired to IRQ 16 > found-> vendor=0x8086, dev=0x2993, revid=0x02 > bus=0, slot=2, func=1 > class=03-80-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > powerspec 2 supports D0 D3 current D0 > map[10]: type 1, range 32, base dff00000, size 20, enabled > found-> vendor=0x8086, dev=0x2834, revid=0x02 > bus=0, slot=26, func=0 > class=0c-03-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > map[20]: type 4, range 32, base 0000ff20, size 5, enabled > pcib0: matched entry for 0.26.INTA > pcib0: slot 26 INTA hardwired to IRQ 16 > found-> vendor=0x8086, dev=0x2835, revid=0x02 > bus=0, slot=26, func=1 > class=0c-03-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=b, irq=10 > map[20]: type 4, range 32, base 0000ff00, size 5, enabled > pcib0: matched entry for 0.26.INTB > pcib0: slot 26 INTB hardwired to IRQ 17 > found-> vendor=0x8086, dev=0x283a, revid=0x02 > bus=0, slot=26, func=7 > class=0c-03-20, hdrtype=0x00, mfdev=0 > cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=c, irq=9 > powerspec 2 supports D0 D3 current D0 > map[10]: type 1, range 32, base dfdfbc00, size 10, enabled > pcib0: matched entry for 0.26.INTC > pcib0: slot 26 INTC hardwired to IRQ 22 > found-> vendor=0x8086, dev=0x284b, revid=0x02 > bus=0, slot=27, func=0 > class=04-03-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > powerspec 2 supports D0 D3 current D0 > MSI supports 1 message, 64 bit > map[10]: type 1, range 64, base dfdfc000, size 14, enabled > pcib0: matched entry for 0.27.INTA > pcib0: slot 27 INTA hardwired to IRQ 16 > found-> vendor=0x8086, dev=0x283f, revid=0x02 > bus=0, slot=28, func=0 > class=06-04-00, hdrtype=0x01, mfdev=1 > cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) > lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > pcib0: matched entry for 0.28.INTA > pcib0: slot 28 INTA hardwired to IRQ 16 > found-> vendor=0x8086, dev=0x2847, revid=0x02 > bus=0, slot=28, func=4 > class=06-04-00, hdrtype=0x01, mfdev=1 > cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) > lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > pcib0: matched entry for 0.28.INTA > pcib0: slot 28 INTA hardwired to IRQ 16 > found-> vendor=0x8086, dev=0x2830, revid=0x02 > bus=0, slot=29, func=0 > class=0c-03-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=5 > map[20]: type 4, range 32, base 0000ff80, size 5, enabled > pcib0: matched entry for 0.29.INTA > pcib0: slot 29 INTA hardwired to IRQ 23 > found-> vendor=0x8086, dev=0x2831, revid=0x02 > bus=0, slot=29, func=1 > class=0c-03-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=b, irq=10 > map[20]: type 4, range 32, base 0000ff60, size 5, enabled > pcib0: matched entry for 0.29.INTB > pcib0: slot 29 INTB hardwired to IRQ 17 > found-> vendor=0x8086, dev=0x2832, revid=0x02 > bus=0, slot=29, func=2 > class=0c-03-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=c, irq=3 > map[20]: type 4, range 32, base 0000ff40, size 5, enabled > pcib0: matched entry for 0.29.INTC > pcib0: slot 29 INTC hardwired to IRQ 18 > found-> vendor=0x8086, dev=0x2836, revid=0x02 > bus=0, slot=29, func=7 > class=0c-03-20, hdrtype=0x00, mfdev=0 > cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=5 > powerspec 2 supports D0 D3 current D0 > map[10]: type 1, range 32, base ff980800, size 10, enabled > pcib0: matched entry for 0.29.INTA > pcib0: slot 29 INTA hardwired to IRQ 23 > found-> vendor=0x8086, dev=0x244e, revid=0xf2 > bus=0, slot=30, func=0 > class=06-04-01, hdrtype=0x01, mfdev=0 > cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) > found-> vendor=0x8086, dev=0x2810, revid=0x02 > bus=0, slot=31, func=0 > class=06-01-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x8086, dev=0x2820, revid=0x02 > bus=0, slot=31, func=2 > class=01-01-8f, hdrtype=0x00, mfdev=0 > cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=c, irq=9 > powerspec 3 supports D0 D3 current D0 > map[10]: type 4, range 32, base 0000fe00, size 3, enabled > map[14]: type 4, range 32, base 0000fe10, size 2, enabled > map[18]: type 4, range 32, base 0000fe20, size 3, enabled > map[1c]: type 4, range 32, base 0000fe30, size 2, enabled > map[20]: type 4, range 32, base 0000fec0, size 4, enabled > map[24]: type 4, range 32, base 0000ecc0, size 4, enabled > pcib0: matched entry for 0.31.INTC > pcib0: slot 31 INTC hardwired to IRQ 20 > found-> vendor=0x8086, dev=0x283e, revid=0x02 > bus=0, slot=31, func=3 > class=0c-05-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0103, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=c, irq=9 > map[10]: type 1, range 32, base dfdfbb00, size 8, enabled > map[20]: type 4, range 32, base 0000ece0, size 5, enabled > pcib0: matched entry for 0.31.INTC > pcib0: slot 31 INTC hardwired to IRQ 20 > found-> vendor=0x8086, dev=0x2825, revid=0x02 > bus=0, slot=31, func=5 > class=01-01-85, hdrtype=0x00, mfdev=0 > cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=c, irq=9 > powerspec 3 supports D0 D3 current D0 > map[10]: type 4, range 32, base 0000fe40, size 3, enabled > map[14]: type 4, range 32, base 0000fe50, size 2, enabled > map[18]: type 4, range 32, base 0000fe60, size 3, enabled > map[1c]: type 4, range 32, base 0000fe70, size 2, enabled > map[20]: type 4, range 32, base 0000fed0, size 4, enabled > map[24]: type 4, range 32, base 0000ecd0, size 4, enabled > pcib0: matched entry for 0.31.INTC > pcib0: slot 31 INTC hardwired to IRQ 20 > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 > pcib1: secondary bus 1 > pcib1: subordinate bus 1 > pcib1: I/O decode 0xf000-0xfff > pcib1: memory decode 0xdfc00000-0xdfcfffff > pcib1: prefetched decode 0xfff00000-0xfffff > pci1: <ACPI PCI bus> on pcib1 > pci1: physical bus=1 > pci0: <display, VGA> at device 2.0 (no driver attached) > pci0: <display> at device 2.1 (no driver attached) > uhci0: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 16 at device 26.0 on pci0 > uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff20 > ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49 > uhci0: [GIANT-LOCKED] > usb0: <UHCI (generic) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <UHCI (generic) USB controller> port 0xff00-0xff1f irq 17 at device 26.1 on pci0 > uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff00 > ioapic0: routing intpin 17 (PCI IRQ 17) to vector 50 > uhci1: [GIANT-LOCKED] > usb1: <UHCI (generic) USB controller> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdfdfbc00-0xdfdfbfff irq 22 at device 26.7 on pci0 > ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdfdfbc00 > ioapic0: routing intpin 22 (PCI IRQ 22) to vector 51 > ehci0: [GIANT-LOCKED] > usb2: waiting for BIOS to give up control > usb2: EHCI version 1.0 > usb2: companion controllers, 2 ports each: usb0 usb1 > usb2: <EHCI (generic) USB 2.0 controller> on ehci0 > usb2: USB revision 2.0 > uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub2: 4 ports with 4 removable, self powered > pci0: <multimedia> at device 27.0 (no driver attached) > pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pcib2: secondary bus 2 > pcib2: subordinate bus 2 > pcib2: I/O decode 0xf000-0xfff > pcib2: memory decode 0xdfb00000-0xdfbfffff > pcib2: prefetched decode 0xfff00000-0xfffff > pci2: <ACPI PCI bus> on pcib2 > pci2: physical bus=2 > pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0 > pcib3: secondary bus 3 > pcib3: subordinate bus 3 > pcib3: I/O decode 0xf000-0xfff > pcib3: memory decode 0xdfa00000-0xdfafffff > pcib3: prefetched decode 0xfff00000-0xfffff > pci3: <ACPI PCI bus> on pcib3 > pci3: physical bus=3 > found-> vendor=0x14e4, dev=0x167a, revid=0x02 > bus=3, slot=0, func=0 > class=02-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > powerspec 3 supports D0 D3 current D0 > MSI supports 1 message, 64 bit > map[10]: type 1, range 64, base dfaf0000, size 16, enabled > pcib3: (null) requested memory range 0xdfaf0000-0xdfafffff: good > pcib3: matched entry for 3.0.INTA > pcib3: slot 0 INTA hardwired to IRQ 16 > bge0: <Broadcom unknown BCM5787, ASIC rev. 0xb002> mem 0xdfaf0000-0xdfafffff irq 16 at device 0.0 on pci3 > bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xdfaf0000 > bge0: firmware handshake timed out > bge0: RX CPU self-diagnostics failed! > bge0: chip initialization failed > device_attach: bge0 attach returned 6 > uhci2: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 23 at device 29.0 on pci0 > uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff80 > ioapic0: routing intpin 23 (PCI IRQ 23) to vector 52 > uhci2: [GIANT-LOCKED] > usb3: <UHCI (generic) USB controller> on uhci2 > usb3: USB revision 1.0 > uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub3: 2 ports with 2 removable, self powered > uhci3: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 17 at device 29.1 on pci0 > uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff60 > uhci3: [GIANT-LOCKED] > usb4: <UHCI (generic) USB controller> on uhci3 > usb4: USB revision 1.0 > uhub4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub4: 2 ports with 2 removable, self powered > uhci4: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0 > uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff40 > ioapic0: routing intpin 18 (PCI IRQ 18) to vector 53 > uhci4: [GIANT-LOCKED] > usb5: <UHCI (generic) USB controller> on uhci4 > usb5: USB revision 1.0 > uhub5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub5: 2 ports with 2 removable, self powered > ehci1: <EHCI (generic) USB 2.0 controller> mem 0xff980800-0xff980bff irq 23 at device 29.7 on pci0 > ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0xff980800 > ehci1: [GIANT-LOCKED] > usb6: EHCI version 1.0 > usb6: companion controllers, 2 ports each: usb3 usb4 usb5 > usb6: <EHCI (generic) USB 2.0 controller> on ehci1 > usb6: USB revision 2.0 > uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub6: 6 ports with 6 removable, self powered > pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pcib4: secondary bus 4 > pcib4: subordinate bus 4 > pcib4: I/O decode 0xf000-0xfff > pcib4: memory decode 0xfff00000-0xfffff > pcib4: prefetched decode 0xfff00000-0xfffff > pcib4: Subtractively decoded bridge. > pci4: <ACPI PCI bus> on pcib4 > pci4: physical bus=4 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH8 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf,0xecc0-0xeccf irq 20 at device 31.2 on pci0 > atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfec0 > ioapic0: routing intpin 20 (PCI IRQ 20) to vector 54 > atapci0: [MPSAFE] > ata2: <ATA channel 0> on atapci0 > atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe00 > atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe10 > ata2: reset tp1 mask=03 ostat0=50 ostat1=00 > ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 > ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 > ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> > ata2: [MPSAFE] > ata3: <ATA channel 1> on atapci0 > atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe20 > atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe30 > ata3: reset tp1 mask=03 ostat0=00 ostat1=00 > ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb > ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb > ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> > ata3: [MPSAFE] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > atapci1: <Intel ICH8 SATA300 controller> port 0xfe40-0xfe47,0xfe50-0xfe53,0xfe60-0xfe67,0xfe70-0xfe73,0xfed0-0xfedf,0xecd0-0xecdf irq 20 at device 31.5 on pci0 > atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfed0 > atapci1: [MPSAFE] > ata4: <ATA channel 0> on atapci1 > atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe40 > atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe50 > ata4: reset tp1 mask=00 ostat0=ff ostat1=ff > ata4: [MPSAFE] > ata5: <ATA channel 1> on atapci1 > atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe60 > atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe70 > ata5: reset tp1 mask=00 ostat0=ff ostat1=ff > ata5: [MPSAFE] > ppc0: using extended I/O port range > ppc0: ECP SPP ECP+EPP SPP > ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > plip0: bpf attached > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > ioapic0: routing intpin 7 (ISA IRQ 7) to vector 55 > sio0: irq maps: 0xca9 0xcb9 0xca9 0xca9 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > sio0: type 16550A > ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56 > ahc_isa_probe 0: ioport 0xc00 alloc failed > ahc_isa_probe 2: ioport 0x2c00 alloc failed > ahc_isa_probe 5: ioport 0x5c00 alloc failed > ahc_isa_probe 6: ioport 0x6c00 alloc failed > ahc_isa_probe 10: ioport 0xac00 alloc failed > ahc_isa_probe 14: ioport 0xec00 alloc failed > ex_isa_identify() > ppc: ppc0 already exists; skipping it > sio: sio0 already exists; skipping it > pnp_identify: Trying Read_Port at 203 > pnp_identify: Trying Read_Port at 243 > pnp_identify: Trying Read_Port at 283 > pnp_identify: Trying Read_Port at 2c3 > pnp_identify: Trying Read_Port at 303 > pnp_identify: Trying Read_Port at 343 > pnp_identify: Trying Read_Port at 383 > pnp_identify: Trying Read_Port at 3c3 > PNP Identify complete > sc: sc0 already exists; skipping it > vga: vga0 already exists; skipping it > isa_probe_children: disabling PnP devices > isa_probe_children: probing non-PnP devices > orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xccfff,0xcd000-0xcefff,0xcf000-0xcffff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > atkbd: the current kbd controller command byte 0045 > atkbd: keyboard ID 0xffffffff (1) > atkbd: failed to reset the keyboard. > kbd0 at atkbd0 > kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000 > ioapic0: routing intpin 1 (ISA IRQ 1) to vector 57 > atkbd0: [GIANT-LOCKED] > psm0: current command byte:0045 > psm0: failed to reset the aux device. > fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > sio1: irq maps: 0xca9 0xca9 0xca9 0xca9 > sio1: probe failed test(s): 0 1 2 4 6 7 9 > sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 > sio2: not probed (disabled) > sio3: not probed (disabled) > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > isa_probe_children: probing PnP devices > ukbd0: DELL DELL USB Keyboard, rev 1.10/1.05, addr 2, iclass 3/1 > kbd2 at ukbd0 > kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000 > Device configuration finished. > Reducing kern.maxvnodes 132076 -> 100000 > linprocfs registered > procfs registered > lapic: Divisor 2, Frequency 133000364 hz > Timecounter "TSC" frequency 2660011320 Hz quality -100 > Timecounters tick every 1.000 msec > Linux ELF exec handler installed > lo0: bpf attached > rr232x: no controller detected. > usb1: host controller halted > ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire > ad4: 76293MB <WDC WD800JD-75MSA3 10.01E04> at ata2-master SATA150 > ad4: 156250000 sectors [155009C/16H/63S] 16 sectors/interrupt 1 depth queue > GEOM: new disk ad4 > ad4: Intel check1 failed > ad4: Adaptec check1 failed > ad4: LSI (v3) check1 failed > ad4: LSI (v2) check1 failed > ad4: FreeBSD check1 failed > ata3: reiniting channel .. > ata3: reset tp1 mask=03 ostat0=00 ostat1=00 > ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb > ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb > ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> > ata3: reinit done .. > ata3: reiniting channel .. > ata3: reset tp1 mask=03 ostat0=00 ostat1=00 > ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb > ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb > ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> > ata3: reinit done .. > ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire > acd0: <TSSTcorpCD-ROM TS-L162C/DE00> CDROM drive at ata3 as master > acd0: read 4134KB/s (4134KB/s), 96KB buffer, UDMA33 > acd0: Reads: CDR, CDRW, CDDA stream, packet > acd0: Writes: > acd0: Audio: play, 255 volume levels > acd0: Mechanism: ejectable tray, unlocked > acd0: Medium: no/blank disc > ATA PseudoRAID loaded > lapic1: Forcing LINT1 to edge trigger > SMP: AP CPU #1 Launched! > cpu1 AP: > ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff > lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff > timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 > INTR: Assigning IRQ 1 to local APIC 0 > ioapic0: Assigning ISA IRQ 1 to local APIC 0 > INTR: Assigning IRQ 4 to local APIC 1 > ioapic0: Assigning ISA IRQ 4 to local APIC 1 > INTR: Assigning IRQ 7 to local APIC 0 > ioapic0: Assigning ISA IRQ 7 to local APIC 0 > INTR: Assigning IRQ 9 to local APIC 1 > ioapic0: Assigning ISA IRQ 9 to local APIC 1 > INTR: Assigning IRQ 16 to local APIC 0 > ioapic0: Assigning PCI IRQ 16 to local APIC 0 > INTR: Assigning IRQ 17 to local APIC 1 > ioapic0: Assigning PCI IRQ 17 to local APIC 1 > INTR: Assigning IRQ 18 to local APIC 0 > ioapic0: Assigning PCI IRQ 18 to local APIC 0 > INTR: Assigning IRQ 20 to local APIC 1 > ioapic0: Assigning PCI IRQ 20 to local APIC 1 > INTR: Assigning IRQ 22 to local APIC 0 > ioapic0: Assigning PCI IRQ 22 to local APIC 0 > INTR: Assigning IRQ 23 to local APIC 1 > ioapic0: Assigning PCI IRQ 23 to local APIC 1 > Trying to mount root from ufs:/dev/ad4s1a > start_init: trying /sbin/init > umass0: Seagate USB Mass Storage, rev 2.00/0.01, addr 2 > umass0: Get Max Lun not supported (STALLED) > umass0:0:0:-1: Attached to scbus0 > pass0 at umass-sim0 bus 0 target 0 lun 0 > pass0: <ST940811 4A \\0000\\0000> Fixed Direct Access SCSI-0 device > pass0: 40.000MB/s transfers > GEOM: new disk da0 > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <ST940811 4A \\0000\\0000> Fixed Direct Access SCSI-0 device > da0: 40.000MB/s transfers > da0: 38154MB (78140160 512 byte sectors: 255H 63S/T 4864C) >Received on Wed Nov 08 2006 - 15:26:28 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:02 UTC
