Re: Any successful installs on a Broadcom HT1000 chipset?

From: Mike Tancsa <mike_at_sentex.net>
Date: Thu, 29 Nov 2007 07:35:45 -0500
At 02:26 AM 11/29/2007, Andrey V. Elsukov wrote:

>May be here is different HW revisions? You have an old revision and 
>now people with this bug have a new revision?
>I don't see in the this thread any verbose dmesg or pciconf outputs.
>So, people, who have problems and who don't have it, can you show
>your `pciconf -l`?

My board works well and has since the 6.1 days

# pciconf -lvc
pcib1_at_pci0:1:0: class=0x060400 card=0x00000000 chip=0x00361166 
rev=0x00 hdr=0x01
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = bridge
     subclass   = PCI-PCI
     cap 07[90] = PCI-X bridge supports
     cap 08[a0] = HT MSI address window enabled at 0xfee00000
     cap 08[b0] = HT slave
hostb0_at_pci0:2:0:        class=0x060000 card=0x02011166 
chip=0x02051166 rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = bridge
     subclass   = HOST-PCI
atapci1_at_pci0:2:1:       class=0x01018a card=0x02141166 
chip=0x02141166 rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = mass storage
     subclass   = ATA
isab0_at_pci0:2:2: class=0x060100 card=0x02301166 chip=0x02341166 
rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = bridge
     subclass   = PCI-ISA
ohci0_at_pci0:3:0: class=0x0c0310 card=0x02231166 chip=0x02231166 
rev=0x01 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = serial bus
     subclass   = USB
     cap 01[dc] = powerspec 2  supports D0 D3  current D0
ohci1_at_pci0:3:1: class=0x0c0310 card=0x02231166 chip=0x02231166 
rev=0x01 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = serial bus
     subclass   = USB
     cap 01[dc] = powerspec 2  supports D0 D3  current D0
ehci0_at_pci0:3:2: class=0x0c0320 card=0x02231166 chip=0x02231166 
rev=0x01 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = serial bus
     subclass   = USB
     cap 01[dc] = powerspec 2  supports D0 D1 D2 D3  current D0
em2_at_pci0:4:0:   class=0x020000 card=0x387010f1 chip=0x10768086 
rev=0x05 hdr=0x00
     vendor     = 'Intel Corporation'
     device     = '82547EI Gigabit Ethernet Controller'
     class      = network
     subclass   = ethernet
     cap 01[dc] = powerspec 2  supports D0 D3  current D0
     cap 07[e4] = PCI-X supports 2048 burst read, 1 split transaction
em3_at_pci0:5:0:   class=0x020000 card=0x387010f1 chip=0x10768086 
rev=0x05 hdr=0x00
     vendor     = 'Intel Corporation'
     device     = '82547EI Gigabit Ethernet Controller'
     class      = network
     subclass   = ethernet
     cap 01[dc] = powerspec 2  supports D0 D3  current D0
     cap 07[e4] = PCI-X supports 2048 burst read, 1 split transaction
none0_at_pci0:6:0: class=0x030000 card=0x002018ca chip=0x002018ca 
rev=0x00 hdr=0x00
     vendor     = 'XGI Technology Inc'
     class      = display
     subclass   = VGA
     cap 01[40] = powerspec 2  supports D0 D1 D2 D3  current D0
rl0_at_pci0:7:0:   class=0x020000 card=0x813910ec chip=0x813910ec 
rev=0x10 hdr=0x00
     vendor     = 'Realtek Semiconductor'
     device     = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
     class      = network
     subclass   = ethernet
     cap 01[50] = powerspec 2  supports D0 D1 D2 D3  current D0
hostb1_at_pci0:24:0:       class=0x060000 card=0x00000000 
chip=0x11001022 rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = 'Athlon 64 / Opteron HyperTransport Technology Configuration'
     class      = bridge
     subclass   = HOST-PCI
     cap 08[80] = HT host
hostb2_at_pci0:24:1:       class=0x060000 card=0x00000000 
chip=0x11011022 rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = 'Athlon 64 / Opteron Address Map'
     class      = bridge
     subclass   = HOST-PCI
hostb3_at_pci0:24:2:       class=0x060000 card=0x00000000 
chip=0x11021022 rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = 'Athlon 64 / Opteron DRAM Controller'
     class      = bridge
     subclass   = HOST-PCI
hostb4_at_pci0:24:3:       class=0x060000 card=0x00000000 
chip=0x11031022 rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = 'Athlon 64 / Opteron Miscellaneous Control'
     class      = bridge
     subclass   = HOST-PCI
     cap 0f[f0] = unknown
pcib2_at_pci1:13:0:        class=0x060400 card=0x00000000 
chip=0x01041166 rev=0xb2 hdr=0x01
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = bridge
     subclass   = PCI-PCI
     cap 07[90] = PCI-X 64-bit bridge supports 133MHz
atapci0_at_pci1:14:0:      class=0x010405 card=0x024a1166 
chip=0x024a1166 rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     class      = mass storage
     subclass   = RAID
     cap 07[60] = PCI-X 64-bit supports 133MHz, 512 burst read, 8 
split transactions
     cap 01[90] = powerspec 2  supports D0 D3  current D0
     cap 05[a0] = MSI supports 1 message
em0_at_pci2:3:0:   class=0x020000 card=0x117a8086 chip=0x10798086 
rev=0x03 hdr=0x00
     vendor     = 'Intel Corporation'
     device     = '82546EB Dual Port Gigabit Ethernet Controller'
     class      = network
     subclass   = ethernet
     cap 01[dc] = powerspec 2  supports D0 D3  current D0
     cap 07[e4] = PCI-X 64-bit supports 133MHz, 2048 burst read, 1 
split transaction
     cap 05[f0] = MSI supports 1 message, 64 bit
em1_at_pci2:3:1:   class=0x020000 card=0x117a8086 chip=0x10798086 
rev=0x03 hdr=0x00
     vendor     = 'Intel Corporation'
     device     = '82546EB Dual Port Gigabit Ethernet Controller'
     class      = network
     subclass   = ethernet
     cap 01[dc] = powerspec 2  supports D0 D3  current D0
     cap 07[e4] = PCI-X 64-bit supports 133MHz, 2048 burst read, 1 
split transaction
     cap 05[f0] = MSI supports 1 message, 64 bit

# cat /var/run/dmesg.boot
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-PRERELEASE #1: Thu Oct 25 21:54:13 EDT 2007
     mdtancsa_at_iolite2.sentex.ca:/usr/obj/usr/src/sys/iolite
ACPI APIC Table: <A M I  OEMAPIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3800+ (2413.18-MHz 686-class CPU)
   Origin = "AuthenticAMD"  Id = 0x40ff2  Stepping = 2
   Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
   Features2=0x2001<SSE3,CX16>
   AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
   AMD Features2=0x1d<LAHF,SVM,ExtAPIC,CR8>
real memory  = 1073676288 (1023 MB)
avail memory = 1041670144 (993 MB)
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
kbd1 at kbdmux0
acpi0: <A M I OEMXSDT> on motherboard
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 13.0 on pci1
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection Version - 6.6.6> port 
0xa880-0xa8bf mem 0xff2c0000-0xff2dffff,0xff280000-0xff2bffff irq 16 
at device 3.0 on pci2
em0: Ethernet address: 00:0e:0c:81:14:d4
em1: <Intel(R) PRO/1000 Network Connection Version - 6.6.6> port 
0xac00-0xac3f mem 0xff2e0000-0xff2fffff irq 17 at device 3.1 on pci2
em1: Ethernet address: 00:0e:0c:81:14:d5
atapci0: <ServerWorks HT1000 SATA150 controller> port 
0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb81f 
mem 0xff3fe000-0xff3fffff irq 11 at device 14.0 on pci1
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
ata4: <ATA channel 2> on atapci0
ata5: <ATA channel 3> on atapci0
atapci1: <ServerWorks HT1000 UDMA100 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 2.1 on pci0
ata0: <ATA channel 0> on atapci1
ata1: <ATA channel 1> on atapci1
isab0: <PCI-ISA bridge> at device 2.2 on pci0
isa0: <ISA bus> on isab0
ohci0: <OHCI (generic) USB controller> port 0xe000-0xe0ff mem 
0xff6b4000-0xff6b4fff irq 10 at device 3.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1: <OHCI (generic) USB controller> port 0xe400-0xe4ff mem 
0xff6b5000-0xff6b5fff irq 10 at device 3.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> port 0xe800-0xe8ff mem 
0xff6b6000-0xff6b6fff irq 10 at device 3.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
em2: <Intel(R) PRO/1000 Network Connection Version - 6.6.6> port 
0xdc00-0xdc3f mem 0xff680000-0xff69ffff,0xff660000-0xff67ffff irq 24 
at device 4.0 on pci0
em2: Ethernet address: 00:e0:81:5e:be:3c
em3: <Intel(R) PRO/1000 Network Connection Version - 6.6.6> port 
0xd880-0xd8bf mem 0xff620000-0xff63ffff,0xff600000-0xff61ffff irq 25 
at device 5.0 on pci0
em3: Ethernet address: 00:e0:81:5e:be:3d
pci0: <display, VGA> at device 6.0 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0xd400-0xd4ff mem 
0xff6b3c00-0xff6b3cff irq 27 at device 7.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:50:fc:a7:9d:04
acpi_button0: <Power Button> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 
0xc0000-0xc7fff,0xc8000-0xc9fff,0xca000-0xcafff,0xcb000-0xcbfff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 2413179713 Hz quality 800
Timecounters tick every 1.000 msec
ad4: 76319MB <Seagate ST380811AS 3.AAE> at ata2-master SATA150
Trying to mount root from ufs:/dev/ad4s1a

         ---Mike 
Received on Thu Nov 29 2007 - 11:37:48 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:23 UTC