Re: CFT: vr(4)

From: Pyun YongHyeon <pyunyh_at_gmail.com>
Date: Tue, 26 Feb 2008 14:34:23 +0900
On Tue, Feb 26, 2008 at 12:03:29AM -0500, Mike Tancsa wrote:
 > At 12:43 AM 2/22/2008, Pyun YongHyeon wrote:
 > > >
 > > > I've put up a new version under the old URL.
 > > > It's not tested in sparc64 but it seems to work on i386.
 > > > Would you give it spin?
 > > >
 > >
 > >Any progress here? Does the updated one works on your box?
 > 
 > 
 > So far so good on my Soekris hardware. I will try some vlan tests tomorrow.
 > 
 > pci0: <encrypt/decrypt, entertainment crypto> at device 1.2 (no 
 > driver attached)
 > vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe100-0xe1ff mem 
 > 0xa0004000-0xa00040ff irq 11 at device 6.0 on pci0
 > vr0: Quirks: 0x6
 > vr0: Revision: 0x96
 > miibus0: <MII bus> on vr0
 > ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
 > ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 > vr0: Ethernet address: 00:00:24:c9:34:88
 > vr0: [ITHREAD]
 > vr1: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe200-0xe2ff mem 
 > 0xa0004100-0xa00041ff irq 5 at device 7.0 on pci0
 > vr1: Quirks: 0x6
 > vr1: Revision: 0x96
 > miibus1: <MII bus> on vr1
 > ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
 > ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 > vr1: Ethernet address: 00:00:24:c9:34:89
 > vr1: [ITHREAD]
 > vr2: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe300-0xe3ff mem 
 > 0xa0004200-0xa00042ff irq 9 at device 8.0 on pci0
 > vr2: Quirks: 0x6
 > vr2: Revision: 0x96
 > miibus2: <MII bus> on vr2
 > ukphy2: <Generic IEEE 802.3u media interface> PHY 1 on miibus2
 > ukphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 > vr2: Ethernet address: 00:00:24:c9:34:8a
 > vr2: [ITHREAD]
 > vr3: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe400-0xe4ff mem 
 > 0xa0004300-0xa00043ff irq 12 at device 9.0 on pci0
 > vr3: Quirks: 0x6
 > vr3: Revision: 0x96
 > miibus3: <MII bus> on vr3
 > ukphy3: <Generic IEEE 802.3u media interface> PHY 1 on miibus3
 > ukphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 > vr3: Ethernet address: 00:00:24:c9:34:8b
 > vr3: [ITHREAD]
 > 
 > This is 7.0-PRERELEASE #0: Mon Feb 25 11:25:31 EST 2008
 > 
 >         ---Mike 
 > 

Thanks again for your testing!
An unresolved issue for Milan Obuch's router board still prevent me
from committing the overhauled one. Unfortunately I still have no
clue why his hardware does not work even though it has the same
hardware revision(0x96).

-- 
Regards,
Pyun YongHyeon
Received on Tue Feb 26 2008 - 04:34:30 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:28 UTC