Re: wireless access point is don`t scaning

Vladimir Ermakov wrote:
> Hello
> 
> after creation access point, she is don`t scaning
> 
> outputs:
> =============================================================
> # ifconfig -a
> re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
>         options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
>         ether 00:1e:90:88:92:85
>         inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
>         media: Ethernet autoselect (100baseTX <full-duplex>)
>         status: active
> ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
>         ether 00:11:6b:63:47:12
>         media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
>         status: running
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
>         inet 127.0.0.1 netmask 0xff000000
> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
>         ether 00:11:6b:63:47:12
>         inet 192.168.5.1 netmask 0xffffff00 broadcast 192.168.5.255
>         media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
>         status: running
>         ssid ora channel 6 (2437 Mhz 11g) bssid 00:11:6b:63:47:12
>         country US ecm authmode WPA privacy MIXED deftxkey 2 TKIP 2:128-bit
>         TKIP 3:128-bit txpower 18.5 scanvalid 60 protmode CTS wme burst ff
>         dturbo dtimperiod 1 -dfs
> 
> # ifconfig wlan0 up scan
> #
> # uname -a
> FreeBSD  8.0-CURRENT FreeBSD 8.0-CURRENT #3: Fri Jul  4 20:01:51 MSD
> 2008     root_at_:/usr/obj/usr/src/sys/GRAVICAPA  i386
> =============================================================
> 
> messages output:
> =============================================================
> Jul  5 13:02:05  kernel: wlan0: ieee80211_ioctl_scanreq: flags 0x13
> duration 0x7fffffff mindwell 0 maxdwell 0 nssid 0
> Jul  5 13:02:05  kernel: wlan0: start_scan_locked: active scan,
> duration 2147483647 mindwell 0 maxdwell 0, desired mode auto, append,
> nopick, once
> Jul  5 13:02:05  kernel: wlan0: scan set 6g dwell min 200 max 200
> Jul  5 13:02:05  kernel: wlan0: scan_next: chan   6g ->   6g [active,
> dwell min 200 max 200]
> Jul  5 13:02:05  kernel: wlan0: send probe req on channel 6 bssid
> ff:ff:ff:ff:ff:ff ssid ""
> Jul  5 13:02:05  kernel: wlan0: scan_next: done, [ticks 5242290, dwell
> min 200 scanend 2152725736]
> Jul  5 13:02:05  kernel: wlan0: notify scan done
> =============================================================
> 
> please, any solution?

The "scan set" lists only channel 6.  Looks like you locked down the 
channel.

	Sam