Re: wireless access point is don`t scaning

On Sat, Jul 5, 2008 at 7:22 PM, Sam Leffler <sam_at_freebsd.org> wrote:
> Vladimir Ermakov wrote:
>>
>> Hello
>>
>> after creation access point, she is don`t scaning
>>
>> outputs:
>> =============================================================
>> # ifconfig -a
>> re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
>>
>>  options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
>>        ether 00:1e:90:88:92:85
>>        inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
>>        media: Ethernet autoselect (100baseTX <full-duplex>)
>>        status: active
>> ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
>>        ether 00:11:6b:63:47:12
>>        media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
>>        status: running
>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
>>        inet 127.0.0.1 netmask 0xff000000
>> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
>> 2290
>>        ether 00:11:6b:63:47:12
>>        inet 192.168.5.1 netmask 0xffffff00 broadcast 192.168.5.255
>>        media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
>>        status: running
>>        ssid ora channel 6 (2437 Mhz 11g) bssid 00:11:6b:63:47:12
>>        country US ecm authmode WPA privacy MIXED deftxkey 2 TKIP 2:128-bit
>>        TKIP 3:128-bit txpower 18.5 scanvalid 60 protmode CTS wme burst ff
>>        dturbo dtimperiod 1 -dfs
>>
>> # ifconfig wlan0 up scan
>> #
>> # uname -a
>> FreeBSD  8.0-CURRENT FreeBSD 8.0-CURRENT #3: Fri Jul  4 20:01:51 MSD
>> 2008     root_at_:/usr/obj/usr/src/sys/GRAVICAPA  i386
>> =============================================================
>>
>> messages output:
>> =============================================================
>> Jul  5 13:02:05  kernel: wlan0: ieee80211_ioctl_scanreq: flags 0x13
>> duration 0x7fffffff mindwell 0 maxdwell 0 nssid 0
>> Jul  5 13:02:05  kernel: wlan0: start_scan_locked: active scan,
>> duration 2147483647 mindwell 0 maxdwell 0, desired mode auto, append,
>> nopick, once
>> Jul  5 13:02:05  kernel: wlan0: scan set 6g dwell min 200 max 200
>> Jul  5 13:02:05  kernel: wlan0: scan_next: chan   6g ->   6g [active,
>> dwell min 200 max 200]
>> Jul  5 13:02:05  kernel: wlan0: send probe req on channel 6 bssid
>> ff:ff:ff:ff:ff:ff ssid ""
>> Jul  5 13:02:05  kernel: wlan0: scan_next: done, [ticks 5242290, dwell
>> min 200 scanend 2152725736]
>> Jul  5 13:02:05  kernel: wlan0: notify scan done
>> =============================================================
>>
>> please, any solution?
>
> The "scan set" lists only channel 6.  Looks like you locked down the
> channel.
>
>        Sam
>

thx
this my mistake
hostap is working and scanning from remote system

P.S. - (ath0 & wlan0) both interfaces have status `running`

/Vladimir Ermakov