OK, I'll try to locate a semilar promise controller or one of the same generation at least and see what gives. It will be a couple of days though before I can get to look into it, time is in short supply currently. -Søren On 31May, 2008, at 23:10 , Sam Leffler wrote: > I understand. Unfortunately this machine wasn't turned on > frequently so it was running an old kernel and pinpointing the > commit is time consuming. > > Sam > > Søren Schmidt wrote: >> HI >> >> There havn't been any changes (AFAIK) to the ATA subsystem lately, >> so it would help if I could get a pointer to when more precisely it >> stopped working ? >> >> -Søren >> >> On 31May, 2008, at 22:13 , Sam Leffler wrote: >> >>> Joe Marcus Clarke wrote: >>>> I have a Dell Precision 360 workstation (i386) with an ATA DVD-RW >>>> drive >>>> and an SATA Seagate drive. After a long time (Feb 14, 2008), I >>>> supped >>>> -CURRENT, and rebooted. Now the box hangs in what appears to be >>>> a probe >>>> of the ATA devices. Here are the last few lines of the verbose >>>> boot >>>> (copied from screen): >>>> >>>> ata0: identify ch->devices=00000000 >>>> ata1: identify ch->devices=00010000 >>>> The GEOM class LABEL is already loaded. >>>> ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire >>>> acd0: setting PIO4 on ICH5 chip >>>> acd0: setting UDMA33 on ICH5 chip >>>> acd0: <HL-DT-ST DVD+RW GRA-4120B/F114> CDRW driver at ata1 as >>>> master >>>> acd0: read 6890KB/s (6890KB/s) write 6890KB/s (6890KB/s), 2048KB >>>> buffer, >>>> UDMA33 >>>> acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet >>>> acd0: Writes: CD, CDRW, test write, burnproof >>>> acd0: Audio: play, 256 volume levels >>>> acd0: Mechanism: ejectable tray, unlocked >>>> acd0: Medium: no/blank disc >>>> ata2: identify ch->devices=00000000 >>>> ata3: identify ch->devices=00000001 >>>> >>>> That's it. After the DVD drive, the only other ATA device is the >>>> SATA-attached Seagate disk which is master on ata3. The previous >>>> kernel's verbose boot reported: >>>> >>>> ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire >>>> ad6: 152627MB <Seagate ST3160815AS 3.AAD> at ata3-master SATA150 >>>> ad6: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 >>>> depth >>>> queue >>>> >>>> This drive is located on a Promise controller: >>>> >>>> atapci0: <Promise PDC20375 SATA150 controller> port 0xcc00-0xcc3f, >>>> 0xcbf0-0xcbff,0xcc80-0xccff mem 0xfe73f000-0xfe73ffff, >>>> 0xfe740000-0xfe75ffff irq 22 at device 1.0 on pci2 >>>> ... >>>> ata3: <ATA channel 1> on atapci0 >>>> >>>> Any ideas? Thanks. >>>> >>>> >>> >>> Not really, just "me too". I updated a machine w/ the same >>> controller and hit the same issue. >>> >>> Sam >>> >>> >>> _______________________________________________ >>> freebsd-current_at_freebsd.org mailing list >>> http://lists.freebsd.org/mailman/listinfo/freebsd-current >>> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org >>> " >>> >> >> >> > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org > " >Received on Sat May 31 2008 - 19:27:22 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:31 UTC