On Aug 23, 2009, at 23:18, Carl Chave wrote: > Did you try booting with the keyboard disconnected from the FreeBSD > machine? Perhaps the vidconsole is favored when a keyboard is > detected? > > On a linux box I had, I would get serial output from Grub, lose it > during kernel load and then get a login once the OS was up, much like > what you describe. I had to add a kernel argument to my Grub config > so the kernel would output to the serial port. > > Did you look here: > http://www.freebsd.org/doc/en/articles/console-server/freebsd.html > > I think 7.2 might be what you are missing but I can't check it myself. > > On Sun, Aug 23, 2009 at 3:13 PM, Thomas > Backman<serenity_at_exscape.org> wrote: >> >> On Aug 23, 2009, at 20:25, Tim Judd wrote: >> >>> On 8/23/09, Thomas Backman <serenity_at_exscape.org> wrote: >>>> >>>> First off: Not subscribed to this list, please make sure to Cc me >>>> if >>>> you don't reply directly. :) >>>> >>>> Anyway, I finally got my null modem cable, and plugged in in >>>> between a >>>> machine running 8.0-BETA2 and one running WinXP using >>>> Hyperterminal. >>>> >>>> My settings: >>>> >>>> /boot/loader.conf: >>>> boot_multicons="YES" >>>> boot_serial="YES" >>>> comconsole_speed="115200" >>>> console="comconsole,vidconsole" >>>> >>>> /etc/ttys: >>>> # Serial terminals >>>> # The 'dialup' keyword identifies dialin lines to login, fingerd >>>> etc. >>>> ttyu0 "/usr/libexec/getty std.115200" vt100 on secure >>>> >>>> /boot.config (which is read properly): >>>> -Dh -S115200 >>>> >>>> Anything wrong in the above? >>>> Hyperterminal is set to 115200 bps, 8 bits, no parity, 1 stop >>>> bit, and >>>> no flow control (if that's the correct translation to English). >>>> >>>> On the serial console, I go from the screen with the FreeBSD logo, >>>> with single-user options etc. (which works fine), and then nothing, >>>> until a login tty pops up (which also works fine). The main, if not >>>> only, reason I want a serial console is to be able to use it for >>>> single user mode, DDB, and so on. >>>> All kernel messages, and all rc messages are seen only on the >>>> graphics >>>> card; the serial console receives nothing but the "/boot.config: - >>>> Dh ...", the logo screen, and then the login screen, during startup >>>> and *nothing* at all during shutdown. Also, I'm able to login and >>>> use >>>> the system both via the serial console and via the graphics card/ >>>> keyboard... Is this supposed to be? I'm not complaining, I just got >>>> the impression it was one or the other. >>>> >>>> Any advice on how to get the kernel/rc messages etc. to the serial >>>> console (only or as well)? >>>> >>>> Regards, >>>> Thomas >>> >>> >>> Do you use the VGA/vidconsole at all? >>> >>> A serial-only device (think soekris, ALIX/WRAP boards) that has no >>> VGA >>> will have different requirements than a serial-only device will. >>> >>> Your loader.conf statements are different than mine in the >>> definition >>> that you have more than I do to enable serial. >>> >>> My loader.conf just has one statement: >>> console="comconsole" - to feed ALL bootloaders, kernel probing, rc >>> startup on the serial device. /etc/ttys defines the login lines. >>> >>> Though trial and error, I found when you use a dual-setup: >>> "comconsole,vidconsole", the first one (comconsole) will get rc >>> output, and vidconsole won't. >>> >>> Of course, you're on 8.0 and I don't run BETAs. So the 8.0 BETA >>> might >>> still be having com port oddities, plus I noticed your ttys line is >>> ttyu0, not ttyd0. Did 8.0 change the serial line device? >>> >>> >>> >>> To enable a serial-only device in my setups: >>> /boot/loader.conf: >>> console="comconsole" >>> >>> /boot.config: >>> -D >>> >>> /etc/ttys: >>> # enable serial line, cons25 or vt100, depending if I'm originating >>> from a bsd or windows box. >>> >>> >>> >>> Enabling dual-setups should be just the loader.conf change to dual >>> console. >>> >>> >>> HTH >> >> >> (Sorry for the lack of inline replies.) >> >> I do have a graphics card, and ideally I'd like to be able to use >> both, but >> serial has higher priority (with serial access, I can use minicom >> on another >> *nix box and essentially ssh into DDB, and stuff like that - right >> now I >> have to borrow a monitor, and write info down manually if needed, >> turning my >> head back and forth). >> >> I've tried lots of combinations of console=, including simply >> 'console="comconsole"' and/or combinations of that and -D, -h- -Dh >> and -P in >> /boot.config. >> The extra lines in loader.conf are from the handbook, which says >> they're >> needed to use comconsole_speed. It seems they do the same thing as - >> D and >> -h, though. >> >> Oh, and re: /etc/ttys: Yup, it's ttyuX when using uart(4) which >> seems to be >> the default now. Actually, since my last buildworld half an hour >> ago I'm on >> 9.0-CURRENT. ;) >> Also, I made sure to set flags to 0x10 for the serial port as per the >> handbook (although I did it using loader.conf, not the kernel >> config); >> before the change, dmesg didn't mention any flags, but it now does. >> Didn't >> help squat, though. >> >> "Though trial and error, I found when you use a dual-setup: >> "comconsole,vidconsole", the first one (comconsole) will get rc >> output, and vidconsole won't." >> This doesn't mirror my experience; comconsole and >> comconsole,vidconsole >> appears to be just the same for me. I've never gotten anything >> except the >> boot loader and a login prompt over to the serial line - at least >> not at >> speed/settings that the client is set up to receive. >> >> I'm gonna try 9600 bps soon just to be sure it isn't that, but >> seeing how >> many others have mentioned using "-S115200" I doubt it'll help. >> >> Thanks/regards, >> Thomas >> _______________________________________________ >> freebsd-questions_at_freebsd.org mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-questions >> To unsubscribe, send any mail to "freebsd-questions-unsubscribe_at_freebsd.org >> " >> Yes, I tried without the keyboard (with -P in boot.config), but apparently it detects the keyboard no matter what (it prints out "Keyboard: yes" even though I yanked the power, then the keyboard, and then started it up again). The article appears to be (even according to itself ;) a shortened version of the handbook ( http://www.freebsd.org/doc/en/books/handbook/serialconsole-setup.html ), which doesn't work out for me, I'm afraid. I'm Cc:ing this to the -CURRENT list in case it's something related to new changes. BTW, 9600 bps didn't help. Same thing, only slower. Regards, ThomasReceived on Mon Aug 24 2009 - 06:17:14 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:54 UTC