Re: Problems with mouse

From: Paul Kuntke <paul_at_kuntke.de>
Date: Thu, 27 Aug 2009 15:14:05 +0200
When I plug in the mouse after booting dmesg says:
ugen0.2: <Microsoft> at usbus0
ums0: <Microsoft Basic Optical Mouse, class 0/0, rev 1.10/0.00, addr 2> on usbus0
ums0: 3 buttons and [XYZ] coordinates ID=0

The output of usbconfig is:
ugen0.1: <OHCI root HUB ATI> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen1.1: <OHCI root HUB ATI> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen2.1: <OHCI root HUB ATI> at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen3.1: <OHCI root HUB ATI> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen4.1: <OHCI root HUB ATI> at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen5.1: <EHCI root HUB ATI> at usbus5, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen5.2: <USB2.0-CRW Generic> at usbus5, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen0.2: <Basic Optical Mouse Microsoft> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON


When the mouse is at boottime plugged in the output of dmesg is:
usb_alloc_device:1588: set address 2 failed (USB_ERR_TIMEOUT, ignored)
usb_alloc_device:1626: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
usbd_req_re_enumerate:1539: addr=2, set address failed! (USB_ERR_TIMEOUT, ignored)
usbd_req_re_enumerate:1553: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
usbd_req_re_enumerate:1539: addr=2, set address failed! (USB_ERR_TIMEOUT, ignored)
usbd_req_re_enumerate:1553: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
ugen2.2: <(null)> at usbus2 (disconnected)
uhub_reattach_port:435: could not allocate new device!

There is no device entry by usbconfig for the mouse:
ugen0.1: <OHCI root HUB ATI> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen1.1: <OHCI root HUB ATI> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen2.1: <OHCI root HUB ATI> at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen3.1: <OHCI root HUB ATI> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen4.1: <OHCI root HUB ATI> at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen5.1: <EHCI root HUB ATI> at usbus5, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen5.2: <USB2.0-CRW Generic> at usbus5, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

-- 
Paul Kuntke <paul_at_kuntke.de>
Jabber-ID: paul_at_42degreesoffreedom.com




Received on Thu Aug 27 2009 - 11:14:57 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:54 UTC